Cuestiones
ayuda
option
Mi Daypo

TEST BORRADO, QUIZÁS LE INTERESENose

COMENTARIOS ESTADÍSTICAS RÉCORDS
REALIZAR TEST
Título del test:
Nose

Descripción:
Alma Cano Merrosas

Autor:
Elber Galarga
(Otros tests del mismo autor)

Fecha de Creación:
20/03/2017

Categoría:
Arte

Número preguntas: 115
Comparte el test:
Facebook
Twitter
Whatsapp
Comparte el test:
Facebook
Twitter
Whatsapp
Últimos Comentarios
No hay ningún comentario sobre este test.
Temario:
Which method of link aggregation do both HP ProVision and Comware switches support? Static LACP Fast Ethernet Dynamic LACP Distributed Trunking.
A company needs a two-member Intelligent Resilient Framework (IRF) virtual switch. The network administrator is configuring IRF member 2 that will connect to port 1/1 on IRF member 1. What is the correct IRF port ID for member 2? 1/2 2/2 1/1 2/1.
A network administrator wants an HP switch to use an IP address that is always up for its Open Shortest Path First (OSPF) router ID. Which address meets this requirement? An IP address configured as the global management address An IP address on the interface for the default VLAN, which is typically VLAN An IP address on the VLAN 1 interface An IP address on a loopback interface.
Refer to the exhibit. The network administrator has configured this port to permit all VLANs. The output in the exhibit indicates that the port is only passing VLANs 1 and 11. The administrator wants the port to pass VLAN 12 as well. What should the administrator do to accomplish this? Enable IP routing. Add VLAN 12 to the switch. Change the port link-type to hybrid. Change the port link-type to access.
Refer to the exhibit. Switch-1 is an HP ProVision switch. A network administrator wants Switch-1 to run Open Shortest Path First (OSPF) and create neighbor relationship on Links 1 and 2. What should the administrator do to accomplish this? Access the VLAN context for the VLANs assigned to Links 1 and 2, and enable OSPF. Access the global configuration context, and create OSPF routes to 10.0.1.0/24 and 10.0.2.0/24. Access the physical interface context for the Link 1 and 2 ports, and enable OSPF. Access the OSPF area 0 context and specify the networks on Links 1 and 2 (10.0.1.0 0.0.0.255 and 10.0.2.0 0.0.0.255).
Which HP software platform provides centralized network management, monitoring, and configuration of wired and wireless network infrastructure devices, as well as traffic monitoring, user management, and other capabilities? HP IntelligentManagement Center (IMC) HP Intelligent Resilient Framework (IRF) HP Virtual Cloud Networking (VCN) HP Virtual Connect FlexFabric.
The exhibit shows partial output of the HP Comwaredisplay ip routing-table command. Note the Preorpreferencecolumn. On an HP ProVision switch, what is the corresponding term used for the Pre column in the Comware output shown in the exhibit? protocol ranking administrative distance cost metric.
An administrator is configuring OSPF on an HP ProVision switch. What is one of the steps that the administrator must take? The administrator must create an OSPF area before assigning a VLAN interface to that area. The administrator must set a global router ID before enabling OSPF. The administrator must set an OSPF router ID before enabling OSPF. The administrator must assign a VLAN interface its IP address before specifying the corresponding network in an OSPF area.
Which endpoint or endpoints receive broadcast ARP requests sent by EndpointA? EndpointB, EndpointC, and EndpointD EndpointB only EendpointB and EndpointC only EndpointC only.
A tagged frame arrives on a switch port that is not a tagged member of the VLAN indicated by the frame ID. What do fundamental VLAN operating rules require the switch to do with that frame? Ignore the VLAN tag and forward the frame, based on destination MAC address. Forward a copy of the frame to the default gateway. Attempt best effort delivery by flooding a copy of the frame to all other VLANs. Drop the frame.
How does Open Shortest Path First (OSPF) help enterprises meet their high availability requirements, compared to RIP? OSPF is usually easier to troubleshoot if problems occur. OSPF has a resilient, non-hierarchical design. OSPF provides faster convergence. OSPF uses less CPU during routing updates.
A customer has an HP ProVision switch capable of Layer 3 forwarding: however, Layer 3 forwarding is disabled. The switch has an IP address in the management VLAN, where the default gateway is 10.1.1.1, which ProVision command should the network administrator use so the ProVision switch can access the Intelligent Management Center (IMC) server in a different VLAN? IP default-gateway 10.1.1.1 IP route 0.0.0.0 255.255.255.255 10.1.1.1 Default-route 10.1.1.1 IP route 0.0.0.0.0.0.0.0 10.1.1.1.
Refer to the exhibit. A network administrator has implemented link aggregation on an HP Comware switch using LACP. The two ports are functioning at the data link layer between the Comware switch and its neighboring switch. The administrator executes the display link-aggregation verbose command and notices the flags shown in the exhibit. What does this indicate? The links are up, but both links are blocked by LACP. The links are up, but are blocked because they are using duplicate operational keys. The links are up, but LACP negotiation has failed on them. The links are up, but LACP is not configured on this link aggregation.
What is the maximum number of active links supported between a device and HP ProVision switches when distributed trunking is used to connect the device to the ProVision switches? Two Four Six Eight.
All of the switches in Exhibit 1 are routing switches. Exhibit 2 shows the routes configured on these switches. The direct (connected) routes are not shown, but assume that links are configured with the IP addresses shown in Exhibit 1. The network administrator wants to protect communications between clients and servers in case Link 1 fails. What should the administrator do to protect these communications in this failover situation? Add a redundant route to 10.1.10.0/24 on Switch-4 and a redundant route to 10.1.20.0/24 on Switch-1. Add a redundant route to 10.1.20.0/24 on Switch-1 and a redundant route to 10.1.20.0/24 on Switch-2. Add a redundant route to 10.1.10.0/24 on Switch-1 and a redundant route to 10.1.20.0/24 on Switch-4. Add a redundant route to 10.1.20.0/24 on Switch-1 and a redundant route to 10.1.10.0/24 on Switch-2.
Which credential is required to validate SNMPv2c write requests? Community string Scheme MD5 authkey AAA authentication.
A customer is implementing an access layer solution with four HP Comware switches in an Intelligent Resilient Framework (IRF) virtual device or domain. The customer expects to add two additional switches of the same model and would like to add them to the existing IRF virtual device. What must the customer verify? that the IRF virtual device has spanning tree enabled on it that the new switches are both assigned the same member ID as the master of the existing IRF virtual device that the IRF virtual device is using a daisy chain topology to provide better resilience that the switch model supports at least six switches in an IRF virtual device.
Which term refers to aggregated links on HP ProVision switches? smart linking meshing EtherChannels trunking.
Which ProVision configuration includes 10.0.3.0/24, which represents VLAN 30 in OSPF area 0? vlan 30 ip ospf area 0 vlan 30 area 0 interface vlan 30 ip ospf area 0 router ospf area 0 vlan 30.
Refer to Exhibit. The server shown in the exhibit requires redundant links, and The link aggregation should use LACP. What should the administrator configure on the IRF virtual switch? a bridge aggregation interface that uses static link aggregation mode a bridge aggregation interface that uses dynamic link aggregation mode two interfaces that are set to trunk for the port-link type two interfaces that are set to hybrid for the port-link type.
Two switches are members in an active Intelligent Resilient Framework (IRF) virtual device. A network administrator joins a third switch to the IRF virtual device. Which switch is now the master? The current master of the IRF virtual device always remains the master. The switch with the lowest member ID always becomes the master. The switch with the lowest priority value always becomes the master. The switch with the highest priority value always becomes the master.
Which command can a network administrator execute on an HP Comware switch to manage configuration files? delete startup-default write file write memory.
Which statement is true about wireless technologies? 802.11b/g uses an 802.11a-compatible frequency. 802.11a has higher data rates than 802.11g does. 802.11n users MIMO technology to improve throughput. 802.11a uses the less crowded 2.4 GHz range.
On an HP Comware switch, which view must an administrator access in order to execute the debug command? Manager Operator System User.
Hotspot Question Match the description with the 802.11 standard. (Each option may be used only once.) Supports channel bonding Supports data rates up to 54 Mbps and operates in the 2.4 GHz band Supports data rates up to 54 Mbps and operates in the 5 GHz band Supports only data rates up to 11 Mbps.
A network administrator configures this command on an HP ProVision switch: vlan 30 ip helper-address 10.0.3.253 The switch is able to ping 10.0.3.253. After the administrator configures the command, users in VLAN 30 report that their PCs fall to acquire addresses using DHCP. What should the administrator ensure? that the switch is configured with a dynamic IP routing protocol that the switch has DHCP relay functions enabled that the switch has DHCP server functions enabled that the switch has an IP address on VLAN 30.
What is the purpose of a management VLAN on an HP Provision switch? To prevent IP addresses from being configured on any VLANs other than the management VLAN To provide an administrative-only marker, label, or alias for the VLAN where IMC is installed To identify a specific VLAN as the only VLAN from which users can connect to the switch management interface To limit remote access connections by specifying the IP addresses that can establish connections.
A network administrator needs to configure DHCP on SwitchA. Assume that SwitchA is an HPE Comware switch and is using the default settings for DHCP. The administrator configures the following information: The administrator then has the DHCP client try to acquire addressing information, but the process fails. What should the administrator do to solve this problem? Execute the routing command on SwitchA. Execute the dhcp enable command on SwitchA. Configure DHCP relay on SwitchB. Enable DHCP Snooping on SwitchA.
Refer to the Exhibit. Exhibit: HP Comware switch configuration. [Comware] vlan 100 [Comware-vlan100] quit [Comware] vlan 200 [Comware-vlan200] quit [Comware] interface g1/0/22 [Comware-GigabitEthernet1/0/22] port link-type trunk [Comware-GigabitEthernet1/0/22] port trunk permit vlan 100 200 [Comware-GigabitEthernet1/0/22] quit A network administrator configures the Comware switch, as shown in the exhibit. The network administrator then connects a cable from the Comware's g1/0/22 interface to port 5 on an HP ProVision switch. Which configuration will successfully establish connection for VLAN 1, 100, and 200 between the two switches? ProVision (config) # vlan 100 ProVision (config) # vlan 200 ProVision (config) # vlan 100 tagged 5 ProVision (config) # vlan 200 tagged 5 ProVision (config) # vlan 100 ProVision (config) # vlan 200 ProVision (config) # interface 5 tagged 100 200 ProVision (config) # vlan 100 ProVision (config) # vlan 200 ProVision (config) # interface 5 tagged 100 ProVision (config) # interface 5 tagged 200 ProVision (config) # vlan 100 200 ProVision (config) # vlan 100 200 tagged 5.
An HP Provision switch has port A1 connected to port g1/0/1 of an HP Comware switch. The ProVision port has the following configuration: vlan 1 untag A1 vlan 10 tag A1 vlan 20 tag A1. Which Comware configuration will allow the three VLANs to successfully pass traffic between the two switches? interface g1/0/1 port link-type trunk port trunk permit vlan 1 10 20 interface g1/0/1 port trunk encapsulation dot1q port trunk native vlan 1 port trunk permit vlan 1 10 20 interface g1/0/1 port trunk port trunk permit auto-vlan interface g1/0/1 port trunk port trunk permit auto-vlan.
Refer to the Exhibit. Originally, all four switches had the same region configuration. VLAN 14 was added to Switch_D and then mapped to instance 2. How does this affect the Multiple Spanning Tree Protocol (MSTP) topology? Load sharing is lost; one of the uplinks is blocked for all traffic on Switch_D. All connectivity is lost; both uplinks are blocked on Switch_D. A Layer 2 loop exists and will cause sporadic connectivity issues. Load sharing is lost; one of the uplinks is blocked for all traffic on Switch_C and Switch_D.
A network administrator enters this command on an HP Comware switch: <Comware> save In interactive mode, the administrator is prompted to save to a file named config.cfg and confirms the save. What is the effect of these actions? The current configuration is saved to config.cfg on a TFTP server but is not used for the startup-config. The startup-config, rather than the correct configuration, is saved to config.cfg on a TFTP server. The current configuration is saved to config.cfg in the flash but is not used for the startup-config. The current configuration is saved to config.cfg in the flash and is used for the startup- config.
An HP ProVision switch is operating at its factory default settings. A network administrator connects the switch to a VLAN with a DHCP server. The switch-to-switch connection is carrying untagged traffic. The administrator wants to log in to the switch CLI using Telnet. How should the administrator contact the switch and log in? Contact the switch at its DHCP-assigned IP address and log in with the default passwordhp. Contact the switch at its default IP address 192.168.1.1/24 and log in without entering a password. Contact the switch at its DHCP-assigned IP address and log in without entering a password. Contact the switch at its default IP address 192.168.1.1/24 and log in with the default passwordhp.
A network administrator is upgrading the operating system on an HP Comware switch. When copying the new image from a TFTP server to the flash of the switch, the process fails because there is not enough flash to store the new operating system. The new operating system is 3.2MB in size. The administrator then executes the commands shown in the exhibit above. Which action should the administrator perform to solve this problem? Execute the reset recycle-bin command, and perform the TFTP transfer again. Execute the clear flash command, and perform the TFTP transfer again. Reformat flash, and perform the TFTP transfer again. Execute the delete old.app command, and perform the TFTP transfer again.
Which HP device or port type can modify, read, and respond with frames that include 802.1Q VLAN tags? Comware trunk ports Comware route-mode ports ProVision loopback ports ProVision untagged ports.
Refer to the exhibit. What can a network administrator determine from the output in the exhibit? The switch will boot the primary software on its next boot. The switch has no software stored in the secondary slot. The switch is using the config file in the primary slot for its startup-config. The switch booted the primary software on its previous boot.
A company wants a modular switch for the access layer at its main campus and for several branch offices. Which HP Switch Series is best suited for this role? HP 11900 HP 12900 HP 5900 HP 5400R.
A server connects to a port on an HP Comware switch. The network administrator wants to ensure that: - The port remains forwarding during Multiple Spanning Tree Protocol (MSTP) topology changes, and - Changes in the port status do not cause MSTP topology changes Which statement describes how the administrator can accomplish this? The administrator must manually configure the port as an STP edge port. The administrator can lower the port's root path cost to zero. The administrator can accept the default behavior of auto-edge. The administrator can configure the port as an MSTP master port.
Which HP solution delivers automated virtual machine orchestrator, automatic synchronization of network connectivity information, and visibility to performance of wired and wireless users? Unified Wired-WLAN modules and switches Intelligent Management Center (IMC) Virtual Connect FlexFabric Intelligent Resilient Framework.
Which statement is true concerning spanning tree protocols and HP switches? ProVision switches use non-standard default cost values Comware switches have spanning tree enabled, by default ProVision switches, by default, auto-sense edge ports Comware switches use their serial number as the switch identifier in the bridge ID.
A network administrator enters this command on an HP ProVision switch with IP routing enabled: ip route 0.0.0.0/0 10.1.1.1 metric 10 distance 10 This is the only IP route to 0.0.0.0/0 on the switch. What is the effect? The switch uses this route for all traffic that does not match a specific route in its routing table. The switch uses this route for all traffic unless the traffic matches a route with a lower administrative distance than 10. The switch uses this route to route all traffic from 10.1.1.1. The switch uses this route for all traffic unless the traffic matches a route with a lower cost than 10.
Refer to the exhibit. Assume that Student A's ARP table is empty. Student A is preparing to send an FTP packet to FTP Server B and needs to discover the proper destination MAC address. For which IP address does Student A send an ARP request? 10.1.10.1 10.1.10.87 10.1.2.2 10.1.20.1.
Refer to the exhibit. A network administrator enters the command shown in the exhibit to check the VLANs on an HP ProVision switch interface. The administrator wants to discover which VLANs are tagged and untagged on the port. What can the administrator do to accomplish this? Enter the show vlans ports 1 command but add detail at the end of the command. View all VLANs on the switch by entering the show vlans command without a VLAN ID. View the physical interface by entering the show interface brief command. Enter the show interfaces all command.
A customer is implementing a network using HP ProVision switches. Which default setting applies to the ProVision switches? All ports are disabled. Routing is enabled. Telnet is enabled. A static IP address is assigned to VLAN 1.
An HP Comware switch should send messages to an SNMP server when various events occur. What is one step in the configuration of this feature? Enable SSH on the switch, and create a user account to match settings on the SNMP server. Set the SNMPv2 read-write community string to match the string on the SNMP server. Enable logging to the console globally. Specify an SNMP trap server with the SNMP server IP address and community string.
An HP switch learns identical valid routes with different protocols. How does the switch choose which route to add to its IP routing table? It adds the route with the highest administrative distance, or route preference. It adds the route with the highest cost. It adds the route with the lowest cost. It adds the route with the lowest administrative distance, or route preference.
What is one difference between Network Segment-based discovery and ARP-based discovery on HP Intelligent Management Center (IMC)? With Network Segment-based discovery, IMC can discover multiple devices. With ARP- based discovery, IMC can only discover one device; the administrator must re-run ARP- based discovery to discover a second device. With Network Segment-based discovery, network device login settings must match login settings on IMC. With ARP-based discovery, only ARP settings must match. With Network Segment-based discovery, network device SNMP settings must match SNMP settings on IMC. With ARP-based discovery, only ARP settings must match. With Network Segment-based discovery, the administrator enters a range of IP addresses to discover. With ARP-based discovery, the administrator enters one seed IP address, and IMC dynamically learns more IP addresses to discover.
A network administrator wants to disable physical interfaces 13-24 on an HP ProVision switch. How can the administrator do this? Create a named port group for interfaces 13-24. Then disable the named port group. Use the interface <ID> disable command. Specify 13-24 for the ID. Assign the range of interfaces to a VLAN. Then, disable the VLAN. Create a named range for interfaces 13-24. Then, disable the named range.
What is a valid reason to choose an 802.11a wireless implementation? It supports a large range (distance) from the AP at a given data speed It has fewer available channels than 802.11b/g, enabling easier deployment It has transmission speed higher than 802.11n It will not interface with an 802.11b/g installation.
Which statement correctly defines the management capabilities of an HP Multi Service Mobility (MSM) access point (AP)? The AP only supports controlled mode. The AP operates in autonomous mode by default, but can be changed to controlled mode. The AP operates in controlled mode by default, but can be changed to autonomous mode. The AP only supports autonomous mode.
When adding a new member to an existing IRF domain, which of the following must you perform first? Define the IRF priority. Create the IRF logical port. Define the IRF domain name. Define the IRF member number.
A network administrator needs to restrict access to the console port of an HPE Comware switch. When a user connects to the console port and opens a terminal session, the switch should prompt the user for a password. How should the administrator configure user interfaces on the Comware switch? Set the authentication mode to password on the VTY 0 15 interfaces and then set the password on the VTY 0 15 interfaces. Set the authentication mode to scheme on the VTY 0 15 interfaces and then set the password globally. Set the authentication mode to password on the AUX 0 interface and then set the password on the AUX 0 interface. Set the authentication mode to scheme on the AUX 0 interface and then set the password globally.
PC1 cannot reach PC2. Based on the exhibits, what could be causing this error? PC1 has the wrong IP address for its default gateway setting. Router A has a direct route, instead of a static route, to 10.1.10.0/24. The next hop address for the 10.1.20.0/24 route is incorrect. Router A has an invalid subnet mask for the VLAN 1 subnet.
A customer wants to implement multiple links between a server and a single HP Comware switch in order to increase the amount of bandwidth for more throughput. Which feature should the network administrator implement to accomplish this? MSTP IRF link aggregation MIMO.
Refer to the exhibit. The switches in the exhibit are all HP Comware switches that run Multiple Spanning Tree Protocol (MSTP). The network administrator wants to ensure that each switch-to-switch link is in its own subnet. The administrator also wants to make sure that all of the links are available for routing during normal operation. How should the administrator configure the physical switch-to-switch interfaces to accomplish these goals? Configure them as trunk ports that permit VLANs 10 and 20. Configure them as any type of port, and make sure spanning tree is enabled on them. Configure them as route-mode ports. Configure them as hybrid ports that carry VLAN 10 and 20 as untagged.
A network administrator is managing an HP Comware switch from the CLI. Which action can the administrator only perform in User view? verifying connectivity with traceroute or ping tools creating a VLAN and assigning ports to it executing display commands viewing files located in flash memory.
An HP Comware switch is using its default user-interface settings. The network administrator then enters the commands shown in the exhibit. What correctly describes how an admin user must now log in? When the admin user logs in to the console port, the admin user must enter either a password of password1 or password2. When the admin user logs in using Telnet, the admin user must enter either a password of password1 or password2. When the admin logs in using Telnet, the admin user must enter a password of password1 and is given level 1 privileges. When the admin user logs in to the console port, the admin user must enter a password of password1 and is given level 3 privileges.
What is one difference between the 802.11g and 802.11n standards? 802.11g can operate on the 5GHz band. 802.11n can operate on the 2.4GHz band. 802.11n supports multiple spatial streams with MIMO. 802.11g supports channel bonding of multiple channels.
What is one reason to access the extended boot menu on an HP Cornware switch? To access the switch CLI when you have forgotten the password To set up the switch to be managed by HP Intelligent Management Center (IMC) To configure the switch initial IP address settings To configure the switch to implement Intelligent Resilient Framework (IRF).
Why does traffic from PC1 fail to reach PC2? Only static routes have been enabled The subnet mask is incorrect on the routers There is no route back from router B A default gateway setting is incorrect.
The topology shown in this exhibit implements Multiple Spanning Tree Protocol (MSTP), where all the switches are in the same region. How many MSTP instances, besides the Internal Spanning Tree (IST) or instance 0, does this network need in order to have effective load sharing on the uplinks from the access switches? two three four five.
A network administrator wants to create a backup IP route to 10.1.20.0/24 on Switch-1. The backup route should use Link 2, and it should only be used if Link 1 is down. What is the correct setup to accomplish this? an IP route through 10.0.2.2 with administrative distance 1 an IP route through 10.1.20.1 with administrative distance 1 an IP route through 10.0.2.2 with administrative distance 10 an IP route through 10.1.20.1 with administrative distance 10.
The network administrator is setting up Multiple Spanning Tree Protocol (MSTP) with the settings shown in the exhibit. All the switches are in the same region. The administrator has requested help determining which VLANs each switch-to-switch link should carry. What is a recommendation for this topology? To prevent disruptions during link failure, Links 1-4 should carry VLANs 10-13. To optimize forwarding, Links 1 and 2 should only carry VLANs 10 and 12, and Links 3 and 4 should only carry VLANs 11 and 13. To ensure compatibility with MSTP, Links 1-4 should be untagged in VLAN 1 and have no tagged VLAN assignments. To optimize forwarding, Links 1 and 3 should only carry VLANs 10 and 11, and Links 2 and 4 should only carry VLANs 12 and 13.
A network administrator has configured an HP Comware switch to act as the DHCP server for VLAN 12, but the switch is not responding to clients' DHCPDISCOVER messages. Based on the exhibit, what is the problem with the DHCP configuration? DHCP is not enabled globally on the switch. DHCP relay is not enabled on VLAN 12. DHCP server is not enabled on VLAN 12. DHCP server ping timeout setting is set too high.
Which methods can a network administrator use to upgrade the operating system of an HP ProVision switch? (Select two) USB FTP SCP SFTP.
What does the traceroute command identify on an HP ProVision switch? each Layer 3 device between the switch and a destination. the path to each router connected to the switch. debug output tracing entries to the routing table. each physical device between the switch and a destination.
A network administrator establishes an aggregated link between an HP Comware and ProVision switch. VLAN 1 is untagged and VLAN 2 and 3 are tagged. The administrator configures these commands on the Comware switch: The administrator configures theses commands on the ProVision switch: Some of the links in the aggregated link become blocked. Which Comware configuration should the administrator apply to the Comware switch to resolve this issues? interface bridge-aggregation 1 link-aggregation mode dynamic interface bridge-aggregation 1 link-aggregation type lacp dynamic interface bridge-aggregation 1 link-aggregation mode static interface bridge-aggregation 1 link-mode type lacp.
Which security benefit does SNMPv3 offer that SNMPv2 does not offer? Data integrity SSL encryption RADIUS groups Scopes.
A network administrator deletes old files in the flash file system of an HP Comware switch. The administrator then notices that the amount of free space available has not changed. Which command must the administrator execute to free up the space from deleted files? reset recycle-bin recycle-bin cleanup cleanup recycle-bin recycle-bon empty.
In the HP Software-defined Networking (SDN) architecture, what connects the Application layer to the physical device or infrastructure layer? HP Network Automation HP SDN Controller HP IMC Virtual Network Manager (VNM) HP IMC SDN Manager.
Which HP solution provides network optimization and automated network provisioning to its customers? Intelligent Management Center NTA FlexNetwork Architecture Intelligent Resilient Framework Software-defined Networking.
Where is priority information stored in an Ethernet frame? 802.1Q VLAN tag IP Precedence field DSCP field TOS tag.
Base on the topology shown in the exhibit, which symptom does a network administrator see if the HP switches are in their factory default states? Mislearned MAC address Unicast storms Multiple ARP requests Layer 3 loop.
Examine the partial HP switch in the exhibit. Based on this output, if the switch receives a packet with a destination IP address of 10.2.90.87, which entry in the routing table would the switch use to forward the packet? 10.2.128.0/17 10.2.0.0/17 10.2.64.0/19 10.2.64.0/18.
A network administrator executes the show vlan commands and see the output shown in the exhibits. How must the administrator configure a connected port on an HP Comware switch? as a trunk port as an access port as an untagged port as a mixed port.
A network administrator configure several HP Comware switches to be part of a single Intelligent Resilient Framework (IRF) virtual device. What is correct about the domain and member IDs in this configuration? The switches have different domain IDs an different member IDs. The switches have the same domain IDs an same member IDs. The switches have the same domain ID and different member IDs The switches have different domain IDs an same member IDs.
The physical interfaces for Comware-1 and Comware-2 switches in the exhibit are configured in routed mode and OSPF. Both switches have three subnets in their routing tables. The administrator wants to use DHCP to assign addressing information to the users, Based on the exhibit, where should the administrator configure DHCP relay? Comware-1. G1/0/2 Comware-1. G1/0/1 Comware-2. G1/0/2 Comware-2. G1/0/1.
Which HP Comware term defines the untagged VLAN on trunk port that is commonly used for network management traffic? default VLAN port VLAN identifier management VLAN access VLAN tag.
The switches in the exhibit are all HP ProVision switches that run Multiple Spanning Tree Protocol (MSTP). The network administrator wants all of the switch-to-switch links shown in the exhibit to be available for forwarding routed traffic. What should the administrator do to accomplish this? Configure the switch-to-switch ports as MSTP auto-edge ports. Configure link-keepalive on the switch-to-switch ports. Configure BPDU filters on the switch-to-switch ports. Configure links on a switch as a standard link aggregation.
80. A network administrator adds a new VLAN in a campus network, VI.AN 120. The administrator needs to set up a DHCP scope for this VLAN. The scope will include an IP address for DHCP clients and a default gateway address. An HP Comware aggregation layer switch acts as a DHCP server for this VLANs at the access layer. The administrator configures this on the Comware switch for the new DCHP scope: Based on this configuration, what else must the administrator configure to make the pool available to DHCP clients that send request in VLAN 120? dhcp vlan 120 dhcp server ip pool qwo Vlan 120 dhcp enable dhcp server vlan 120.
A company requires switches to use Multiple Spanning Tree Protocol (MSTP) instead of Rapid Spanning Tree Protocol (RSTP), so that the switches can forward traffic on more than one switch-to-switch link. How does the administrator ser up the solution to meet this requirement? Configure every switch with a unique bridge priority in the IST, which is also called spanning tree instance 0. Ensure that switches use the 802.3t standard costs instead of the legacy costs. Set the same spanning tree cost on all redundant links on a switch. Map different VLANs to different instances, and make a different switch root bridge in each instance.
A network administrator configures OSPF in an HP ProVision based network. The administrator is concerned that a rogue device might connect to an access layer switch and introduce OSPF routes to the company´s routing topology. The access VLANs do not contain additional routes. Which configuration should the administrator apply for these access VLANs to prevent them from forming an adjacency with rogue devices? router ospf no vlan <VLAN-ID> neighbor -adjacency router ospf ip silent-vlan <VLAN-ID> router ospf passive-vlan <VLAN-ID> vlan <VLAN-ID> ip ospf passive.
All four switches run MSTP. Switch_A, Switch_B, and Switch_C are configured with this MSTP information: - Config name="Region 1" - Revision number=1 - Instance 1= VLANs 10, 12 - Instance 2= VLANs 11, 13 - IST instance= VLANs 1-9, 14-4094 Switch_D is configured with this MSTP information: - Config name="Region 1" - Revision number=1 - Instance 1= VLANs 10, 12 - Instance 2= VLANs 11, 13,14,15 - IST instance= VLANs 1-9, 16-4094 Based on this information, what is the result of this MSTP configuration? Switch_D load balances VLAN traffic to Switch_A and Switch_B. Switch_D disables the links to Switch_A and Switch_B. Switch_D becomes a root switch. Switch_D causes a loop.
A network administrator wants to create a routed topology that ensures redundant connections between User Group 1 and User Group 2. Based on this information, how many broadcast domains should the administrator create? Two Three Four Seven.
What is one feature that MSTP has that RSTP does not have? load-sharing on redundant links alternate root ports multiple designated ports per segment one set of BPDUs per VLAN.
A mid-size company purchases HP Intelligent Management (IMC) to manage 500 nodes. In addition to the base platform, the company purchases the UAM, WSM, and NTA modules. Which deployment method should this use to install their IMC base platform and modules? Stand-alone Distributed Centralized Hierarchical.
Which FlexNetwork architecture component provides high performance and low-latency for virtual and physical servers that provide services to the users in a company? FlexFabric FlexDataCenter FlexNet FlexArchitecture.
A network administrator sets up OSPF in part of the network topology shown in the exhibit. The Comware-1 switch is already configured. The administrator needs to configure ProVision-1 so that: -OSPF includes VLANs 10 and 20 in the routing process. -The router ID of 1.1.1.1 is assigned to the switch. -The ProVision-1 switch can successfully build a neighbor adjacency with the Comware-1 switch. Which configuration should the administrator apply to the ProVision-1 switch to meet these requirements? ip ospf area 0 vlan 20 ip ospf area 0 router ospf router -id 1.1.1.1 area 0 vlan 10 area 0 vlan 20 enable router ospf router -id 1.1.1.1 area 0 vlan 10 area 0 vlan 20 ip router -id 1.1.1.1 router ospf area 0 enable vlan 10 ip ospf area 0 vlan 20 ip ospf area 0.
An endpoint device requests an address by using DHCP. What is the first message the client sends to initiate this process? DHCPPREQUEST DHCPQUERY DHCPDISCOVER DHCPOFFER.
A company wants to implement HP Intelligent Resilient Framework (IRF) at the access layer. Which switches could they use? two HP 5500 HI Series switches one HP 5412R zl2 Series switch and one HP 5800 Series switch one HP 5800 Series switch and one HP 5500 Series switch two HP 5406R zl2 Series switches.
Exhibit: HP Comware switch configuration Based on the exhibit output, which type of link aggregation is this? dynamic trunk protocol static trunking dynamic port group static LACP.
A network administrator has copied new software to an HP ProVision switch and placed this software in the secondary flash location. The switch is currently booting from the primary flash location. The administrator wants the switch to start using the new software. What should the administrator do to accomplish this? Execute the command to boot the system from the secondary flash. Reboot the switch, which automatically causes the switch to use the newer software. Copy the secondary software to the primary software slot. Rename the secondary software as the primary software.
When configuring Multiple Spanning Tree Protocol (MSTP), how should VLANs be separated to perform load balancing? placed into separate instances configures with different priority values never configured with more than one VLAN per instance placed into separate regions.
Based on the output shown in this exhibit, which statement is true about the 10.0.0.2 neighbor? The neighbor is communicating with this switch, but it cannot hold any more routes in its database. The neighbor is communicating with this switch, and they have exchanged all topology information. The neighbor has mismatched setting and cannot exchange information with this switch. The neighbor is rejecting communications because it already has its maximum number of neighbors.
How does a switch treat a link aggregation? The switch treats each interface within the interface as a separate entity for MAC address learning; it also assigns an individual spanning tree port role to each interface. The switch treats the link aggregation as one logical link for spanning tree, but it learns MAC addresses separately on each individual interface within the aggregation. The switch treats the link aggregation as one logical link. It assigns one spanning tree port role to the link aggregation, and it learns MAC address on the aggregation. The switch treats the link aggregation as one logical link for MAC learning, but it assigns an individual spanning tree port role to each interface within the aggregation.
Based on the output in the exhibit, which statement is correct about the spanning tree protocol running in this network? Switch-C is a root switch. Port 2 is a designated port. Port 3 is a root port. Port 4 is a designated port.
What does the output indicate about GE1/0/1? The interface accepts untagged traffic, which it assigns to VLAN 1. It drops traffic that is tagged for VLANs 1, 10, and 20. The interface accepts untagged traffic, which it assigns to VLAN 1. It also accepts traffic that is tagged for VLANs 10 and 20. The interface accepts untagged traffic, which it assigns to VLAN 1. It accepts traffic that is tagged for any VLAN between 10 and 20. The interface does not accept untagged traffic. It accepts traffic that is tagged for VLANs 1, 10, and 20.
A network administrator executes these commands on an HP ProVision switch: ProVision (config) # ip route 10.1.100.0/24 10.1.1.1 ProVision (config) # ip route 10.1.200.0/24 10.1.1.1 The administrator attempts to ping a device in the 10.1.100.0/24 network from a client attached to the switch and is unable to ping it. Assume there are no firewalls and all other settings are correct. What must the administrator configure on the ProVision switch to get a response? ProVision (config) # ip routing ProVision (config) # spanning-tree disable ProVision (config) # routing enable ProVision (config) # routing ProVision (config-router) # ip enable.
The topology shown on the left of the exhibit illustrates a traditional three-tier architecture. Which technology allows a company to simplify their network with a two-tier topology as illustrated on the exhibit. Intelligent Resilient Framework Software-defined Networking Multiple Spanning Tree Protocol Equal Cost Muti-Pathing.
What is true the community string used for SNMPv1 and SNMPv2c? The community string encrypts the SNMP message, but does not hash it, providing for data privacy. The community string hashes the SNMP message, but does not encrypt it, providing for data privacy. The community string encrypts and hashes the SNMP message, providing for data integrity and privacy. The community string is like a password transmitted in clear text, providing no data integrity or privacy.
A network administrator wants to join a switch to an Intelligent Resilient Framework (IRF) virtual device. The administrator changes the switch member ID from 1 to 2. What must the administrator do before configuring the IRF port on this switch? Physically connect the switch to the IRF master device. Reboot the switch. Disable IP routing. Enable the physical interfaces that will be assigned to the IRF port.
A network administrator wants to establish an LACP link aggregation between an HP Comware switch and an HP ProVision switch. Which settings should the administrator configure? The link aggregation mode should be set to static on the Comware bridge interface, and the ProVision trunk should be set to lacp. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to trunk. The link aggregation mode should be set to static on the Comware bridge interface, and the ProVision trunk should be set to trunk. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to lacp.
A network administrator examines an HP Comware switch that is configured to route packets between VLANs. The switch is configured with multiple routing protocols. All routing protocols have of the same destination network. All routing protocols use the default administrative distances. Which routing protocol does the switch select for the destination network? EIGRP Indirect OSPF Static route.
MSTP is configured on all switches shown in the exhibit. The Comware-1, Comware-3, and Comware-4 switches are set up for OSPF. Comware-1 and Comware-4 switches fail to achieve neighbor adjacency. The network administrator analyzes the issue and determines that MSTP is blocking on port gigabitethernet 1/0/2 on Comware-1. Which configuration should the administrator configure on ports g1/0/1 and g1/0/2 to allow Comware-1 to form the correct OSPF adjacencies with Comware-3 and Comware-4? interface g1/0/1 spanning ing-tree bpdu-filter quit interface g1/0/2 spanning ing-tree bpdu-filter quit interface g1/0/1 undo stp enable quit interface g1/0/2 undo stp enable quit interface g1/0/1 stp link-mode route quit interface g1/0/2 stp link-mode route quit interface g1/0/1 stp bpdu-filter quit interface g1/0/2 stp bpdu-filter.
A network administrator plans to execute show commands as well as make conjuration changes. Which HP ProVision privilege role must be assigned to an account for the administrator to do this? Operator Administrator Superuser Manager.
A customer purchases HP Intelligent Management Center (IMC) to help manage their network. The customer needs access to real-time and historical data about user and applications that consume bandwidth. Which IMC module should the customer purchase? NTA WSM UAM EAD.
Which statement is true about the default configuration on an HP ProVision switch? Spanning tree is disabled. LACP is used when a BAGG interface is created. IRF is enabled. RSTP is the default spanning tree mode.
A company has a network comprised of HP Comware and ProVision switches. A network administrator purchases HP Intellingent Management Center (IMC) to manage the switches in this network. Which step must the administrator perform on the Comware switches but on the ProVision switches? Configure SNMP traps. Configure VTY interface authentication. Define SNMPv2c community strings or SNMPv3 groups and users. Configure telnet or SSH.
Examine the HP Comware switch output show in the exhibit. Based on this output, what is a correct description of the IRF topology with which this switch is associated? This is a failed IRF daisy chain topology. This is a functioning IRF chain topology. This is a functioning IRF ring topology. This is a failed IRF ring topology.
Which setting enable a network administrator to use terminal emulation software to interface with an HP Comware switch´s auxiliary port? 9600 bps, 7 data bits, stop bit, no parity, flow control 14,200 bps, 8 data bits, 1 stop bit, parity, flow control 9600 bps, 8 data bits, 1 stop bit, no parity, no flow control 9600 bps, 8 data bits, 1 stop bit, parity, no flow control.
A network administrator is configuring a static route. What should the administrator use as the next hop address? the IP address on the local interface that is used to egress traffic towards its destination the lowest IP address on the neighboring router in the path towards its destination the IP address on the connected interface of a neighboring router in the path towards its destination the IP address of the default gateway in the destination subnet.
Which privilege level would a network administrator use to configure an HP ProVision switch? Super User Manager Administrator.
A company has a policy that requires all administrators to use secure access for in-band management. The administrator sets up SSH access on the HP Comware switches in the network to meet this requirement. The administrator enables SSH, and creates SSH keys and administrator accounts on the Comware switches. Every time the administrator attempts to log in the switches the SSH access is denied. The VTYs are configured as: user-interface vty 0 15 authentication-mode password user privilege level 3 quit What is the authentication mode the administrator must configure on the VTYs of the Comware switch so the switch prompts for username and passwords? username aaa scheme local.
This switch currently assigns all VLANs to Multiple Spanning Tree Protocol (MSTP) instance 0 or the Internal Spanning Tree (IST). Which statement correctly describes interface 21? The interface is down at Layer 2; it is not available for sending or receiving any traffic. The interface isan edge port but has received Bridge ProtocolDataUnits (BPDUs), so it is disabled. The interface does not forward or accept data traffic, but it is ready to start forwarding if interface 19 fails. The interface does not support spanning tree; it is possible that it will introduce a loop in the network.
Examine the output from the Comware command shown in the exhibit. Based on the flag of ACDEF, what is the status of the aggregated link? Static LACP link aggregation is configured, and the aggregated link is operational with load sharing not being performed. Static link aggregation is configured, and the aggregated link is operational with load sharing being performed. Static LACP link aggregation is configured, and the aggregated link is operational with load sharing being performed. Static link aggregation is configured, and the aggregated link is operational with load sharing not being performed.
Denunciar test Consentimiento Condiciones de uso