There are three locations in a school district of a large city: ROUTER -M, ROUTER -W and ROUTER -U. The network connection between two of these locations has already functioned. Configure the ROUTER -M router IP addresses on the E0 and S0 interfaces so that the E0 receives the first usable subnet while the S0 receives the second usable subnet from the network 192.168.160.0/28. Both interfaces would receive the last available ip address on the proper subnet. ROUTER-M> enable
Password: Cisco ROUTER-M# config t
ROUTER-M(config)# interface e0 ROUTER-M(config-if)# ip address 192.168.160.14 255.255.255.240
ROUTER-M(config-if)# no shutdown
ROUTER-M(config-if)# exit ROUTER-M(config)# interface s0
ROUTER-M(config-if)# ip address 192.168.160.30 255.255.255.240
ROUTER-M(config-if)# no shutdown ROUTER-M(config-if)# end
ROUTER-M# copy run start.
Which option is a valid hostname for a switch? Switch-Cisco Switch-Cisco! SwitchCisco SwitchCisc0.
Which component of the routing table ranks routing protocols according to their preferences? administrative distance next hop metric routing protocol code.
Which statement about unicast frame forwarding on a switch is true? The TCAM table stores destination MAC addresses If the destination MAC address is unknown, the frame is flooded to every port that is configured in the same VLAN except on the port that it was received on. The CAM table is used to determine whether traffic is permitted or denied on a switch The source address is used to determine the switch port to which a frame is forwarded.
Which statement about native VLAN traffic is true? Cisco Discovery Protocol traffic travels on the native VLAN by default Traffic on the native VLAN is tagged with 1 by default Control plane traffic is blocked on the native VLAN. The native VLAN is typically disabled for security reasons.
Which route source code represents the routing protocol with a default administrative distance of 90 in the routing table? S E D R O.
Refer to the exhibit. Which statement describes the effect of this configuration? The VLAN 10 VTP configuration is displayed. VLAN 10 spanning-tree output is displayed. The VLAN 10 configuration is saved when the router exits VLAN configuration mode. VLAN 10 is added to the VLAN database.
When enabled, which feature prevents routing protocols from sending hello messages on an interface'? virtual links passive-interface directed neighbors OSPF areas.
Which device allows users to connect to the network using a single or double radio? access point B. switch wireless controller firewall.
Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true? IP routing must be enabled to allow the two hosts to communicate. The two hosts are in the same broadcast domain. The switch must be configured with a VLAN to allow the two hosts to communicate. Port security prevents the hosts from connecting to the switch.
Which NTP command configures the local device as an NTP reference clock source? ntp peer ntp broadcast ntp master ntp server.
Which routing protocol has the smallest default administrative distance? IBGP OSPF IS-IS EIGRP RIP.
Which statement about static routes is true? The source interface can be configured to make routing decisions. A subnet mask is entered for the next-hop address. The subnet mask is 255.255 255.0 by default The exit interface can be specified to indicate where the packets will be routed.
By default, how many MAC addresses are permitted to be learned on a switch port with port security enabled? 8 2 1 0.
Which statement about a router on a stick is true? Its date plane router traffic for a single VI AN over two or more switches. It uses multiple subinterfaces of a single interface to encapsulate traffic for different VLANs on the same subnet. It requires the native VLAN to be disabled. It uses multiple subinterfaces of a single interface to encapsulate traffic for different VLANs.
Which network topology allows all traffic to flow through a central hub? bus star mesh ring.
Which NAT type is used to translate a single inside address to a single outside address? dynamic NAT NAT overload PAT static NAT.
What is the default lease time for a DHCP binding? 24 hours 12 hours 48 hours 36 hours.
Which RFC was created to alleviate the depletion of IPv4 public addresses? RFC 4193 RFC 1519 RFC 1518 RFC 1918.
Which method does a connected trunk port use to tag VLAN traffic? IEEE 802 1w IEEE 802 1D IEEE 802 1Q IEEE 802 1p.
Configuration of which option is required on a Cisco switch for the Cisco IP phone to work? PortFast on the interface the interface as an access port to allow the voice VLAN ID a voice VLAN ID in interface and global configuration mode Cisco Discovery Protocol in global configuration mode.
Under which circumstance should a network administrator implement one-way NAT? when the network must route UDP traffic when traffic that originates outside the network must be routed to internal hosts when traffic that originates inside the network must be routed to internal hosts when the network has few public IP addresses and many private IP addresses require outside access.
Which component of a routing table entry represents the subnet mask? routing protocol code prefix metric network mask.
When a router makes a routing decision for a packet that is received from one network and destined to another, which portion of the packet does if replace? Layer 2 frame header and trailer Layer 3 IP address Layer 5 session Layer 4 protocol.
On which type of device is every port in the same collision domain? a router a Layer 2 switch a hub.
Which statement about routing protocols is true? Link-state routing protocols choose a path by the number of hops to the destination. OSPF is a link-state routing protocol. Distance-vector routing protocols use the Shortest Path First algorithm. IS-IS is a distance-vector routing protocol.
Which technology supports the stateless assignment of IPv6 addresses? DNS DHCPv6 DHCP autoconfiguration.
Which feature allows a device to use a switch port that is configured for half-duplex to access the network? CSMA/CD IGMP port security split horizon.
Which function enables an administrator to route multiple VLANs on a router? IEEE 802 1X HSRP port channel router on a stick.
Which dynamic routing protocol uses only the hop count to determine the best path to a destination? IGRP RIP EIGRP OSPF.
What is one requirement for interfaces to run IPv6? An IPv6 address must be configured on the interface. An IPv4 address must be configured. Stateless autoconfiguration must be enabled after enabling IPv6 on the interface. IPv6 must be enabled with the ipv6 enable command in global configuration mode.
Which destination IP address can a host use to send one message to multiple devices across different subnets? 172.20.1.0 B. 127.0.0.1 192.168.0.119 239.255.0.1.
Which MTU size can cause a baby giant error? 1500 9216 1600 1518.
Which entity assigns IPv6 addresses to end users? ICANN APNIC RIR ISPs.
Which option is the default switch port port-security violation mode? shutdown protect shutdown vlan restrict.
Which statement about the inside interface configuration in a NAT deployment is true? It is defined globally It identifies the location of source addresses for outgoing packets to be translated using access or route maps. It must be configured if static NAT is used D. It identifies the public IP address that traffic will use to reach the internet. It must be configured if static NAT is used D. It identifies the public IP address that traffic will use to reach the internet.
Which value is indicated by the next hop in a routing table? preference of the route source IP address of the remote router for forwarding the packets how the route was learned exit interface IP address for forwarding the packets.
|
