option

A320 ENGINES

INFORMACIÓN ESTADÍSTICAS RÉCORDS
REALIZAR TEST
Título del test:
A320 ENGINES

Descripción:
ENGINES

Autor:
Walter Moreira
(Otros tests del mismo autor)

Fecha de Creación:
17/02/2014

Categoría:
Test de conducir

Número preguntas: 65
Comparte el test:
Facebook
Twitter
Whatsapp
REALIZAR TEST
Últimos Comentarios
No hay ningún comentario sobre este test.
Temario:
1.- A few seconds after selecting reverse, the amber REV indication changes to green. What does this mean? A.- The reversers have been re-stowed. B.- The reversers are now fully deployed. C.- The reverse thrust selection has been acknowledged. D.- The reversers are unlocked.
2.- During engine start the amber FAULT light on the ENG MASTER panel illuminates. This indicates: A.- A failure in the automatic start sequence. B.- A failure of the ENG MODE SELECTOR. C.- A failure in the engine fire extinguishing system.
3.- Which steps of a manual start are being taken care of by the FADEC? A.- Starter valve closure and ignition cut off. B.- Starter valve opening and ignition start. C.- Starter valve closure and ignition start. D.- Starter valve opening and ignition cut off.
4.- Can Alpha-floor be disengaged while in Alpha Protection? A.- Yes, by manually disengaging the auto throttles. B.- No, the system is designed to avoid such a disengagement. C.- Yes, by reducing at idle one of the throttles (for more than 5 seconds).
5.- Is it possible to disconnect Alpha floor? A.- No, Alpha floor protection is always available. B.- Yes, by placing the thrust levers to IDLE. C.- Yes, by depressing the autothrottle push button on the FCU.
6.- The FADEC will automatically abort an abnormal start thereby providing engine limit protection, but will the FADEC also automatically dry crank the engine? A.- No, that is why there is a CRANK selection on the ENG MODE selector. B.- Yes, even if the crew interrupts the start by placing the ENG MASTER switch to OFF. C.- Yes, as long as the ENG MASTER switch remains in the ON position.
7.- What would happen in flight if the FADEC's alternator failed? A.- Automatic controlof the engine would be lost. B.- The standby channel of the ECU would take over. C.- The FADEC would now be powered using ship's power. D.- The FADEC would now be powered using ship's battery power.
8.- You are in the middle of a manual engine start. What are you looking for when you select ENG MASTER 2 ON? A.- The fuel used is reset, fuelflow is indicated and IGNITION message on the E/IVD. B.- The fuel flow is reset, an igniter is powered and fuel used is indicated. C.- The fuel used is reset, both igniters are powered and fuelflow is indicated. D.- The fuel used is reset, both igniters are powered and N2 is increasing.
9.- Each FADEC is a dual channel (A&B) computer providing full engine management. A.- True. B.- False.
10.- In addition to when the engine is operating, when else will the FADEC be powered? A.- When the FADEC GND PWR pb on the maintenance panel is depressed, or the ENG MASTER switch is placed to ON. B.- When the FADEC control switch is placed to the IGN/START position. C.- For five minutes after electrical power is applied to the aircraft, when the FADEC GND PWR pb on the maintenance panel is depressed, or when the ENG MODE control switch is placed to IGN/START position. D.- As long as electrical power is established on the aircraft, the FADEC is powered.
11.- During an automatic start, the FADEC controls: A.- The start valves, igniters and fuel flow. B.- The start valves, igniters, HP and LP fuel valves. C.- The igniters and fuel flow. D.- The start valves, igniters, HP and LP fuel valves, and fuel flow.
12.- How is manualarming of the A/THR system accomplished? A.- By pressing the A/THR pb on the FCU confirm the pushbutton illuminates green or confirm an A/THR annunciation is displayed in column 5 of the FMA. B.- By placing the thrust levers into the active range. C.- Advance at least one thrust lever to the TOGA or LX/I CT detent with at least one Flight Director (FD) on.
13.- You are at the start of a descent and a blue N I arc is displayed showing the new thrust demand. When does this happen? A.- Whenever the thrust levers are moved out of the CLIMB position. B.- Whenever there is a power change in manual thrust. C.- Whenever there is a power change with the autopilot engaged. D.- Whenever there is power change with auto thrust engaged.
14.- If a thrust lever is set between two detents, the FADEC selects the rating limit corresponding to the higher limit. A.- True. This limit is displayed on the uppr ECAM. B.- False. For safefy reasons, it always selects the rating limit corresponding to the lower limit.
15.- What would happen during the takeoff roll if the thrust levers were set to the FLXA4CT detent without FLEX temperature being entered? A.- Nothing, the thrust setting would be at FLEX since FADEC automatically calculates a reduced thrust setting. B.- The thrust setting would be MCT and there would be no corresponding warnings. C.- A LEVEL TWO warning would sound along with the appearance of an ECAM messase.
16.- What abnormals would cause the FADEC to automatically abort a start? A.- A hot start, an overtemp, a stalled start or no lightoff. B.- An engine overspeed. C.- A hot start, a stalled start, an overtemp or APU underspeed. D.- A hot start, an overtemp or an engine overspeed.
17.- During an in-flight start or a manual start, will the FADEC auto abort for an abnormal? A.- Yes. It will for an in-flight start (but not for a manual start). B.- Yes. C.- No.
18.- For reverser actuation, the left engine uses _ hydraulic system pressure and the right engine uses - hydraulic system pressure. A.- Green - Yellow. B.- Yellow - Blue. C.- Yellow - Green. D.- Blue - Green.
19.- While flying the airplane with A/THR active, the speed knob is pulled and turned to a selected speed that happens to be slower than Alpha prot. What speed will the airplane slow to? A.- Vls. B.- Green Dot + 5 kts. C.- Green dot. D.- Green dot + l0 kts.
20.- Where is the thrust reduction altitude found and is the number always the same? A.- Column four, row three of the FMA. It willalways be 1500 ft. AGL. B.- TAKE OFF PERF page of the MCDU (it can be modified). C.- PROG page of the MCDU. It can be modified in order to meet constraints. D.- TAKE OFF PERF page of the MCDU. It cannot be modified.
21.- During a manual start, what function does the FADEC perform? A.- Passive monitoring of the start sequence, to close the start valve and cut off the ignition on the ground. B.- To control the start sequence and take corrective action in case of a failure or malfunction. C.- The FADEC does not perform any function during a manual start and all actions have to be carried out by the pilots.
22.- During normal operation, in what detent are the thrust levers positioned once the thrust reduction altitude has been reached? A.- CL. B.- MCT. C.- FLX. D.- CRZ.
23.- After take off the A/THR will not become active until: A.- The thrust levers are placed in the CLIMB position. B.- The thrust levers are moved out of the TO/GA or FLE)IMCT detents. C.- The autopilot is engaged. D.- The A/THR pushbutton is manually selected ON.
24.- Continuous ignition is provided automatically when: A.- ENG ANTI ICE is selected ON and/or engine flameout is detected in flight. B.- ENG ANTI ICE is selected ON. C.- ENG ANTI ICE is selected ON and/or ensine flameout is detected in flight and/or the EIU fails.
25.- How can A/THR be ARMED automatically? A.- Whenever a takeoff or go-around is initiated with at least one flight director ON. B.- When Alpha floor protection is activated. C.- Both are correct.
26.- During a manual start, how is the start valve opened? A.- It is automatic once the ENG MASTER is placed to the ON position. B.- By depressing the ENG MAN START pushbutton's on the overhead panel. C.- By depressing the ENG MAN START pushbutton's on the overhead panel while the ENG MODE selector is out of the NORM position.
27.- When does oil quantity indication begin to pulse? A.- Decreasing below 5 qts. B.- During engine start. C.- Oil quantity detector or pressure fault.
28.- Does the FADEC provide EGT limit protection constantly? A.- Yes, in all phases of flight. B.- No, EGT limit protection is only available during ground auto starts. C.- No, EGT limit protection is only available during ground auto starts and single-engine operations.
29.- No, EGT limit protection is only available during ground auto starts and singleengine operations. A.- Both throttles are above idle but not above the CLB detent when both engines are running. B.- A single throttle of an operating engine is above idle but not above the MCT detent when one engine is running. C.- All of the above.
30.- The idle setting on the aircraft is capable of modulating due to certain conditions. During descent, what might cause the IDLE Nl setting to increase? A.- The slats are extended. B.- For a higher than normal bleed air demand or warrner than normal engine oil temp in flight. C.- Both are correct.
31.- Verification that Autothrust (A/THR) is active can be made by: A.- Watching the automatic movement of the thrust levers. B.- Only when the thrust levers are set at TOGA. C.- Only by looking at column frve of the FMA.
32.- When Alpha floor is activated, what power setting is automatically commanded and what FMA annunciation would appear in Column one? A.- TOGA / A. FLOOR B.- CLB/CLB. C.- MCT / THR LK. D.- THR/LK.
33.- Holding the instinctive disconnect push button's for more than fifteen seconds will: A.- Disengage the A/THR (including Alpha Floor) until below 1000 feet AGL for the remainder of the flight. B.- Disengage the A/THR (including Alpha Floor) until below 500 feet AGL for the remainder of the flight. C.- Disengage the A/THR (excluding Alpha Floor) for the remainder of the flight. D.- Disengage the A/THR (including Alpha Floor) for the remainder of the flight.
34.- During the automatic start sequence of ENG 2,you notice that only igniter B is powered. Is it normal? A.- Yes, igniter A is only used for engine anti-ice. B.- No, normally both igniters are used for all engine starts. C.- Yes, igniter B is always used for ENG 2 start. D.- Yes, igniters are used alternately for engine start.
35.- As far as FMA annunciations are concerned. what would indicate that the A/THR system is active? A.- SPEED appears in green in column one, line one. B.- AITHR changes from blue to white as shown in column five, line three. C.- A/THR changes from white to blue in column five, line one. D.- SPEED appears in amber in column one, line one.
36.- If the thrust levers are set in the idle detent, is Alpha floor protection still available? A.- Yes. Thrust lever position is disregarded. B.- Yes, as long as'A/THR'appears in Column five. C.- No, because the IDLE detent is out of the A/THR active range.
37.- Is there any mechanical linkage between the thrust levers and the engines? A.- There is a fiber optic backup. B.- There is a mechanical linkage in case the ECU fails. C.- No, it is electrically powered and hydraulically actuated. D.- No, it is totally electrical.
38.- What is Alpha floor protection? A.- It helps prevent the aircraft from stalling and protects against windshear encounters during takeoff and approach. B.- It is a function of the flight control laws to prevent the aircraft from stalling. C.- It helps prevent the aircraft from stalling by limiting the angle of bank at low airspeeds. D.- It helps prevent the aircraft from stalling by limiting the angle of climb at high airspeeds.
39.- Alpha floor protection is available: A.- From lift off and down to 100 feet radio altitude in the landing configuration. B.- From lift off and down to 50 feet radio altitude in the landing configuration. C.- From lift off and down to 500 feet radio altitude in the landing configuration. D.- From lift off and down to 750 feet radio altitude in the landing configuration.
40.- How do you arm the A/THR in flight? A.- A/THR switch ON when throttles are in the engagement mode. B.- A/THR switch ON when throttles are not in the engagement mode.
41.- What is the difference between variable thrust and the speed mode? A.- In the fixed thrust mode, thrust is fixed and the elevator controls the speed. B.- In the variable thrust mode, thrust is fixed and speed is controlled by the elevator. C.- In the fixed thrust mode, thrust is variable and speed is controlled by the elevator.
42.- The left column, first line of the FMA is used to indicate: A.- If A/THR is off, armed, or active. B.- The mode of the A/THR in use when A/THR is armed or active. C.- Amber caution messages. D.- The thrust indication.
43.- What are the two basic modes of the A/THR system? A.- Thrust and Mach. B.- Thrust and speed. C.- Variable thrust and fixed speed. D.- Mach and speed.
44.- Is any thrust lever action required if an engine failed at rotation while using FLEX takeoff power? A.- Yes. B.- No.
45.- Can the engines be overboosted in the TOGA position? A.- Yes, if the autothrust function is not active. B.- No, because the ECU provides engine protection limit by monitoring N l, N2, and HMU fuel flow adjustments C.- No, because the EIU is responsible for monitoringNl and N2.
46.- What does the FLEX represent in the FLX/MCT detent? A.- This is a reduced thrust setting used for takeoff. B.- This is the maximum continuous thrust setting for single-engine operations. C.- This is the thrust setting that should be chosen in the case of a single engine goaround. D.- This is a derated thrust according the ground temperature of the day.
47.- How many FADEC's are installed in the aircraft? A.- I Two, one per engine. B.- One, with two Engine Control Units (ECU). C.- Two per engine. D.- Two, one is the active FADEC and the other is a standby.
48.- What is required for the FADEC to compute a reduced thrust setting? A.- A FLEX temperature must be entered on the INIT page of the MCDU. B.- Nothing, it is an automatic function of the FADEC. C.- A FLEX temperature must be entered on the TAKE OFF PERF page of the MCDU.
49.- Using manual thrust, the thrust lever position will determine the thrust setting for the engine. A.- True. They will operate like conventionalthrottles. B.- True, but care must be taken not to overspeed the engines. C.- False. the next hieher detent will be the thrust limit.
50.- What is considered to be the active range of the A/THR system? A.- During single engine operations from just above the IDLE stop to the FLX/MCT detent. B.- During two engine operations from just above the IDLE stop to the CL detent. C.- Both are correct.
51.- During an automatic start sequence; selecting the ENG MASTER switch to on: A.- Closes the pack valves. B.- Initiates the start sequence. C.- Displays the ECAM engine page. D.- First two statements are correct.
52.- The FADEC has control during a manual engine start sequence except for: A.- The high pressure fuel valve. B.- The start valve. C.- An automatic abort.
53.- Continuous ignition is automatically provided during the following: A.- Flex or TO/GA thrust is selected on the ground. B.- ENG ANTICE switch is ON. C.- Engine surge on stall occurs in flight. D.- Any or the above.
54.- The A/THR is armed on the ground provided at least on FD is on by: A.- Setting the throttles to TO/GA. B.- Automatically at engine start. C.- With engines running; pressing the A/THR p/b manually.
55.- If a throttle is set between two detents; the FADEC selects the rating limit. A.- Determined by the throttles position. B.- Corresponding to the higher mode. C.- Corresponding to the lower mode.
56.- When the A/THR system is in use: A.- The throttles move automatically according to FADEC commands. B.- The throttles can only be moved manually. C.- The throttles will move when the A/THR p/b is used.
57.- A/THR engagement is confirmed when 'A/THR' is displayed in _____ in the right column of the FMA. A.- Green. B.- Blue. C.- White.
58.- If an A/THR disconnect switch is pushed and held for more than _____ seconds; the A/THR system is disconnected for the remainder of the flight; including the ____. A.- 10 seconds - Alpha floor Protection. B.- 12 seconds - Alpha floor Protection. C.- 15 seconds - Alpha floor Protection. D.- 18 seconds - Alpha floor Protection.
59.- Takeoff can be performed using which power settings? A.- Any manual setting. B.- FLEX and MCT. C.- CLIMB and TO/GA. D.- FLEX/MCT and TO/GA.
60.- When is T.O. INHIBIT and LDG INHIBIT active? A.- To 750 feet AGL, LND below 1500 feet AGL. B.- To 1000 feet AGL, LND below 1000 feet AGL. C.- To 1500 feet AGL, LND below 750 feet AGL. D.- To 1500 feet AGL, LND below 1000 feet AGL.
61.- How many thrust lever positions are there, and how are they labeled? A.- There are 6 thrust levers positions: TO/GA, MCT, FLEX, CL, IDLE and REV IDLE. B.- There are 6 thrust levers positions: TO/GA, FLX/MCT, CL, IDLE, REV IDLE and MREV. C.- There are 4 thrust levers positions: TO/GA, FLX/MCT, CL, IDLE. D.- There are 5 thrust levers positions: TO/GA, FLX/MCT, CL, IDLE and REV IDLE.
62.- You are just about to take off. You have not inserted a FLEX temperature. Can you still takeoff? A.- Yes, by setting the thrust levers to the CLIMB detent. B.- Yes, by setting the thrust levers to the FLEX/MCT detent. C.- Yes, but only using the TO/GA detent. D.- Not until a FLEX temperature in inserted.
63.- During an engine start sequence, the gray background on N2 disappears at about 57%. What does this indicate? A.- That the igniters are no longer being powered. B.- That the start sequence has finished and all engine parameters have stabilized. C.- That the star valve air pressure has dropped. D.- That there is a start fault and a dry crank is in progress.
64.- The full authority digital engine control (FADEC) controls which of the following functions. A.- Fuel metering. B.- Engine limits. C.- Automatic and manual starting. D.- All of the above.
65.- The FADEC is normally powered by: A.- The RAT. B.- Its own magnetic alternator. C.- The normal aircraft electrical system.
Denunciar test Condiciones de uso
INICIO
CREAR TEST
INFORMACIÓN
ESTADÍSTICAS
RÉCORDS
Otros tests del Autor