administracion-aix

A customer has a virtualized system using Virtual I/O Server with multiple client partitions accessing the SAN using NPIV? Which command on the client partition should be run to retrieve the network address of the fiber adapter?. lscfg -vp –l fcs0. lspci –vafcsi | grep “Network Address”. lspath –npiv fcs0 | grep “NetworkAddress”. lsdev | grep fcs0.

Where is a Cluster Aware AIX cluster configuration data stored?. A NFS filesystem that is accessible by all nodes. A shared disk that is accessible from all nodes. A master copy on one node and the data is replicated to the local disk of the other nodes. A shared system pool that is accessible by all nodes.

How can a system administrator verify the progress of an AIX client installation from the NIM master?. nim-o check <client>. lsnim –l<client>. nim –status <client>. tail –f /var/adm/ras/nimclient_<client>.

What is the minimum version of AIX that is supported as a Versioned WPAR on an AIX 7.1 system?. AIX 5.3 TL12 SP4. AIX 5.2 TL10 SP8. AIX 6.1 TL3 SP2. AIX 5.1 ML8.

The administrator cannot ping the hostname of any system on the local network, including LPARs in the same managed system that have virtual Ethernet adapters configured on the same subnet and VLAN. What is the most likely cause of this problem?. The Ethernet cable from the system to the switch is disconnected or faulty. The Shared Ethernet Adapter in the Virtual I/O Server in the managed system is not passing communication between virtual adapters and the network. The routing table has been flushed on the host and the default route is no longer configured. DNS is disabled and the /etc/hosts file on the host does not contain the addresses for the host names that are being pinged.

What are the three basic elements of RBAC in AIX?. Groups, Keys, and Access. Users, Groups, and KeyStore. Keys, Privileges, and Groups. Roles, Privileges, and Authorizations.

When attempting to log into a system, the administrator receives the message “All network ports in use.” How can this be resolved?. Add the terminals tty0 through tty9 to the /etc/securetty file. Use the no command to enable ipforwarding. On the HMC, select the option “Reset Connection” for the server. Use the chdev command to increase the number of pseudo-terminals.

A VIO client will use NPIV to boot from the SAN and needs to be installed using NIM. Which two methods can be used to gather the WWPN information? (Choose two.). Examine the NIM client properties. Boot the LPAR and run lscfg –vlfcsX. Utilize the HMC command line tool, lssyscfg. Log into the VIO servers and run lscfg –vlfcsX. Check the LPAR properties from the HMC GUI.

Which file needs to be modified to export a NFS file-system as read-only?. /etc/xtab. /etc/rmtab. /etc/security/exports. /etc/exports.

Which performance tool can be used to determine if any particular partitions of a logical volume are more heavily accessed than others?. lplayout. fileplace. lvmstat. sar.

A failed integrated tape drive was physically replaced in a Power Systems server. Without performing any additional operations, the administrator attempts to use the device and receives this AIX error message: AN ERROR OCCURRED WHILE WRITING TO THE STORAGE MEDIA THE DEVICE IS NOT READY FOR OPERATION What is the likely cause?. The media inside the failed tape drive was not removed. The tape drive needs to be powered on before being used. The tape device microcode needs to be updated. The drive was replaced but the new device information was not configured.

Which option will prevent users in the DBA group from logging in using telnet or rlogin?. Remove the users in the DBA group from the /.rhosts file. Change the rlogin group attribute to ‘false’. Disable the automatic start-up of the telnetd daemon. Set the rlogin user attribute to ‘false’ for each user in the DBA group.

An AIX instance was initially configured to communicate over a single network interface. The administrator plans to configure an EtherChannel using the existing network interface and an additional network interface. What is the correct sequence of steps to implement this configuration?. Remove the existing IP information Add both interfaces as primary adapters Configure the IP address. Configure the same IP address on the additional interface Add both adapters as primary adapters Remove the existing default route. Configure the existing interface as a primary adapter Configure the additional interface as a backup adapter. Add both adapters as primary adapters Configure the IP address as an alias on the additional interface.

Additional space is required in /tmp to allow snap to run to completion. There is NOT enough unallocated space in rootvg to increase /tmp to the required size. There IS enough free space within a secondary volume group. How can the file system configuration be updated to allow snap to run successfully?. Use mirrorvg with the -I parameter to mirror just /dev/hd3 to the secondary volume group and extend the file system. Create a new logical volume in the secondary volume group, then increase the /tmp file system capacity with extendfs. Create a new file system within the secondary volume group and mount it over /tmp/ibmsupt. Dynamically move /tmp into the secondary volume group with migratepv and extend the file system capacity with chfs.

Which command can be run to clean up a previous snap?. snap -c. errlog -c. snap -r. errclear.

What action will prevent the nfsd subsystem from activating at boot time?. Remove the /etc/export file. Change the Action attribute from ‘wait’ to ‘once’ for the rcnfs line within the /etc/inittab. Disable –a boot=no /usr/bin/nfsd. Update /etc/inetd.conf to remove the call to startsrc for the NFS subsystem group.

An administrator saved a change to the active profile of an LPAR. When will the change take effect?. Immediately after the profile is saved. When the Rebuild Managed System task completes. When the LPAR is shut down and re-activated. When the admin reboots the LPAR from within AIX.

A customer wants to edit the CPU and memory settings in a template that is used in the environment. How should this be accomplished?. Edit HMC V7 system template. Edit HMC V8 system template. Edit HMC V7 partition template. Edit HMC V8 partition template.

An administrator wants to change an LDAP user to use local files to authenticate. What should the administrator change?. Registry attribute. Kerberos server. SYSTEM attribute. LDAP server.

Which two components are required to support VLANs in an AIX partition? (Choose two.). IEEE 802.1Q capable switch. IEEE 802.1Q compatible adapter and driver. IEEE 802.11n compatible adapter. IEEE 802.15.4 capable switch. IEEE 802.3ad compatible interface.

An LPAR is hosted on Power8 hardware. How can an adapter assigned as “required” to that LPAR be removed with minimal downtime?. Initiate the Add/Remove procedure from the ASMI. Use the CHARM tool to remove the adapter. Remove the device through diag, and DLPAR remove the adapter. Remove the required setting in the profile, and DLPAR remove the adapter.

An administrator wants to migrate data in a volume group from one set of disks to a new set of disks. No free disks are currently available within the volume group. What must be done before migrating the data to the new disks?. The new disks must be added to the volume group with extendvg and then migrate the data. The volume group must be imported to the new disks with importvg. The volume group must be varied off with varyoffvg before adding the new disks. The new disks must be formatted for a volume group with chdev and then extended.

An administrator is attempting to recover the sendmail.cf file from the weekly mksysb backup. The following output confirms that the file does exist within the mksysb backup: Why does the SMIT panel above fail to find and restore the required file?. The file to restore must be correctly delimited relative to the backup. Extended attributes should not be restored for a symbolic link. /etc/mail/sendmail.cf is a symbolic link to /etc/sendmail.cf. The target directory must match the source directory.

A volume group is mirrored to two external storage systems. One of the storage systems is rebooted for maintenance. After the storage system is up and available, lsvg shows a disk in a missing state: Which command will change the PV STATE from missing to active?. cfgmgr –vlhdisk2. syncvg –v datavg. chdev –l hdisk2 –a state=active. varyonvgdatavg.

A customer wants to restore amksysb using a NIM server while using the least amount of disk space possible. Which set of actions does the customer need to take?. Define mksysb resource, create lpp_source from mksysb resource. Define mksysb resource, create spot from lpp_source resource. Define mksysb resource, create spot from mksysb resource. Define spot resource, create lpp_source from mksysb resource.

A customer has plugged a notebook into the HMC1 port of a brand new POWER8 server. The customer is attempting to get to the ASMI menu. Why is nothing being displayed on the notebook?. The notebook is not set up to accept a DHCP address from the service processor. The notebook is configured for IPv4 and the service processor only communicates via IPv6. The notebook is not on the same subnet as the service processor. The notebook needs to be plugged into the HMC2 port for the ASMI menu to be displayed on the notebook.

Given the following topas output: What does the Entc% value represent?. Percentage of Ethernet consumed. Performance statistics for all logical CPUs in the system. Percentage of physical capacity consumed. Percentage of entitled capacity consumed.

How can an administrator use the logical volume information returned by the lslv –m command?. To determine the current state of the logical volume. To determine which physical partitions are free for use by the logical volume. To determine which physical partitions are allocated to the logical volume. To determine the amount of available (unused) space in the logical volume.

The first line of a script is: #!/usr/bin/perl What will this do when the script is run?. It will execute the file /usr/bin/perl before executing the script. It will load environment variables in the /usr/bin/perl file. It will interpret the script using Perl. It will set the value of the “perl” environment variable to the empty string.

Which type of resource is required for every BOS installation performed with NIM?. bosinst_data. script. resolv_conf. spot.

What procedure can be used to recover an AIX system that will not boot due to a corrupted boot logical volume?. Power on the system and enter SMS mode Select Diagnostics and Problem Determination Select the option to Recover Boot Logical Volume. Boot the system into maintenance mode using amksysb Select the System Backup and Install menu Select the option to Recover Devices. Boot the system into maintenance mode using AIX installation media Select the Start Maintenance Mode for System Recovery menu and access the root volume group Issue the bosboot command for the rootvg disk. Boot the system into maintenance mode using amksysb Select the Start Maintenance Mode for System Recovery menu and access the root volume group Copy the /SPOT/dev/hd5 to /dev/hd5 and run syncvgrootvg.

Which command will change the database object for the primary dump device to dumplv permanently?. sysdumpdev –P –p /dev/dumplv. sysdumpdev –d /dev/dumplv. mkdumpdev –p /dev/dumplv. sysdumstart –p /dev/dumplv.

An administrator is tasked with enhancing the data availability and I/O load balancing for an AIX 7.1 system attached to IBM storage. Which action will satisfy the requirement?. Set the correct host type on the storage array and match the failover settings on the AIX instance. Adjust the health check interval attribute for each hdisk presented from the storage array. Install the appropriate path control module to work in conjunction with the native MPIO driver. Remove the native MPIO driver and replace with the appropriate path control module.

Which action must be completed on the HMC when a Recovery state is discovered?. Select Initialize Partition for the LPAR in Recovery state. Select Recover Partition Data for the Managed System. Select Configuration and Rebuild Managed System. Select Configuration and Restore partition data.

Which statement about interim fix management is correct with regard to planned maintenance?. If the updates include the official APAR, the update_all process will automatically uninstall the interim fix. The interim fix will be automatically committed as part of the update process. The interim fix must be manually committed prior to applying the updates. If the fileset associated with interim fix will not be updated, it still needs to be temporarily rejected.

An administrator uses the ‘no’ command to change the tcp_sendspace network tunable to 262144. A few minutes later, the ifconfig command produces the following output: What additional action is needed?. Run the no command again, specifying a permanent change. Change the tcp_sendspace interface specific network option for the device. Refresh the inetd subsystem. Use ifconfig to cycle the interface down and up.

Which configuration is a requirement when migrating an LPAR via LPM (Live Partition Mobility)?. LPARs with dedicated I/O adapters can be migrated using LPM, provided the same dedicated I/O adapters are available on the destination system. Physical disk attributes for backing devices must have the same reservation policy set on both source and target VIO Servers. The destination system must have the same virtual adapter slots free on its VIO Server as the source system. The source and destination systems must be managed by different HMC devices.

An administrator is trying to export a file system on a server to external clients. How can the administrator determine if all required NFS services are currently active?. lsitabrcnfs. lssrc -a. nfsd -l. ps –ef | grep nfsd.

What should be considered when creating a file system with a small fragment size of 512 bytes?. The maximum size of a file is reduced. The total number of inodes is decreased. The maximum file system size limit is reduced. The disk I/O operations will increase.

How can an administrator configure the storage on a POWER8 system running AIX, with no single points of failure in the disk storage, for a database volume group?. Configure two local SAS adapters and use RAID-10. Configure a 2-port HBA adapter with redundant paths to SAN storage. Configure a local SAS adapter and use RAID-5 with a hot spare. Assign virtual storage through a VIO Server.

What determines whether all AIX systems in the virtual environment are at a specified software and fix level and provide an alerting mechanism?. Trusted Network Connect and Patch Management. AIX Network Install Manager. IBM PowerVC – Virtualization Center. Security and Compliance Automation.

Which file lists all tunables and associated values applied during the last reboot?. /etc/tunables/nextboot.log. /etc/tunables/lastboot.log. /etc/tunables/nextboot. /etc/tunables/lastboot.

Which statement regarding the at command is true?. Jobs using at can be scheduled at regular intervals if the batch job queue is selected. When the at command is run it retains the current environment. When running the at command, an optional duration may be specified for automatic process termination. The atd daemon must be running in order for at jobs to be processed.

Which command, when issued from the HMC command line, will attempt to launch a virtual terminal session on Ipar1, running on the sys1 managed system?. mkvterm-msys1 -p Ipar1. crvterm-ssysy -r Ipar1. startvt-h sys1 -I Ipar1. startx-vt sys1 -p Ipar1.

Given the this output of the Iparstat -i’ command from an LPAR, which statement is true?. There are 8 physical CPUs installed configured into 2 processor pools. All active CPUs are dedicated to this LPAR. There are 8 active CPUs available for sharing and another 8 active for dedicated use. The LPAR can automatically use up to 8 physical CPUs. The LPAR can utilize processing capacity from any of the active CPUs.

How can an administrator rename hdisk2 to cldisk1?. chpv-n cldisk1 hdisk2. rendev-I hdisk2 -n cldisk1. clcmd-I hdisk2-d cldisk1. chdev-I hdisk2-aname=cldisk1.

An administrator has noticed that root receives email every day, stating that the Electronic Service Agent (ESA) has not been configureD. The company does not use ESA and the administrator would like the daily emails to stop. How can this be achieved?. Use SMIT to configure the Electronic Service Agent. Remove the entry generating the email from root’s crontab. Have an IBM SSR add the ESA keys to the HMC. Order an MES for the system, specifying the feature code to refuse ESA.

Which command will read a volume group backup stored at/dev/cd1 and restore the /myapp/app.c file to the /data/testcode directory?. restorevgfiles -f /dev/cd1 -s -d /data/testcode ./myapp/app.c. restvg -d /dev/cd1 -s -f /data/testcode./myapp/app.c. restore -Tqvf/dev/cd1 -s -d /data/testcode ./myapp/app.c. listvgbackup -restore /dev/cd1 -s -f/data/testcode ./myapp/app.c.

Where is the file size limit for all users defined?. /etc/security/environ. /etc/security/limits. /etc/security/environments. /etc/environment.

An LPAR has been assigned additional memory and the administrator would like to confirm the new memory size. Which TWO commands will display LPAR total memory? (Select 2). memstat. Isattr -EI sys0 -a realmem. getconf REAL_MEMORY. Iscfg-vlmem0. lsmem.

An administrator needs to limit the size of the filesystem cache. Which tuning parameters need to be adjusted?. minfree and maxfree. minperm and maxperm. minfreemem and maxfreemem. minpgahead and maxpgahead. sb_min and sb_max.

What is a mandatory requirement to allow an AIX 7-based NIM Master to install clients over IPv6?. The NIM Master must use static IPv6 addresses. The NIM Master must have both IPv4 and IPv6 connectivity. The NIM Master must be installed with the AIX Enterprise Edition license. The NIM Master must be running at least AIX 7.1 TLOO Service Pack3 or later.

Which component must be available to Cluster Aware AIX on each node to support cluster communication?. An lPv6 link-local address on each node. A dedicated vLAN that is not used for any other purpose. An lPv4 network address. A disk used only for heartbeat communication.

After unexpected system crash, the administrator runs the “df” command and notices that a user file system is not mounted, even though the mount flag is set to “true” in /etc/filesystems file. Which process will mount the file systems?. Certify the disks, reboot the system. Certify the disks, change the mount flag to “automatic”. Change the mount flag to “automatic”, run “fsck” on the file systems. Run “fsck” on the file system, run “mount all”.

Crontab file fields are defined as shown here: minute hour day_of_month month weekday command How should the following crontab entry be modified so that “command” only executes once on the first and fifteenth of every month? 0 0 1, 15 * 1 command. 0 * 1, 15 * 1 command. 0 0 1, 15 * 0 command. 0 0 1-15 * 1 command. 0 0 1, 15 * * command.

A server on the 165.x.x.x subnet is displaying network problems. The administrator uses a console connection and gathers the following information: Which action will permanently resolve the issue?. Flush the routing table. Run 'route del 10.2.98.113-f. Modify/etc/routes and reboot the system. Run 'chdev-I inet0-a delroute=net.-hopcount,0,,0.10.2.98.113'.

An administrator noticed that the hostname is being resolved incorrectly after setting up TCP/IP on multiple interfaces. Further inspection shows the /etc/hosts file has duplicate entries for the hostname associated with different IP addresses. Which of the following is most likely the cause of this situation?. IPv6 is in use and requires a hostname for every interface. The administrator ran smitty mktcpip on multiple interfaces. The DNS configuration has multiple separate DNS servers listed. An EtherChannel was setup using 2 network interfaces as primary adapters.

An administrator is required to create a System WPAR and configure it for mobility, which command will do this?. mkwpar-c wparname. mkwpar-m wparname. crwpar-c wparname. crwpar-m waprname.

The AIX hosts node1 and node2 have Ethernet adapters, both named ent0, configured on the same network. Both are dedicated physical 1GB adapter ports in a Host Ethernet Adapter. Based on this information and the output shown for each node, what is the most likely cause of intermittent failures and slow communication between these adapters?. The jumbo_frarnes setting is 'no' and should be set to 'yes'. The Multi-Core Scaling mode is enabled. Multi-Core Scaling is interfering with communications because the processor is too busy. The Shared Ethernet Adapter does not have enough bandwidth to accommodate the network traffic. The media speed is set differently on the adapters than the endpoints on the switch.

Which startup script will mount all filesystems in /etc/filesystems for which the mount parameter is set to 'true'?. /etc/rc. /etc/red. /sbin/rc.start. /etc/rc.bootc.

Which tool or function can minimize the impact of planned operating system downtime on active workloads?. Integrated Visualization Manager. Live Application Mobility. Partition Flexibility Mirror. Dynamic Hosting Environment. Micro-Partitioning. Live Partition Mobility. Shared Storage Pools.

What is the purpose of the virtual media repository on the VIO Server?. To store resources for use by the NIM server. To store backups of the VIO Server. To store images for use by VIO Clients. To store images for use by VIO Servers.

A customer has been creating LPARs on a new POWER8 system. After successfully activating the first 10 LPARs, the customer notices that the available RAM on physical machine reported by the HMC has reduced more than the sum of the memory currently allocated to the activated LPARs. The Customer appreciates there will be a memory overhead for each activated LPAR, but the overhead appears more than expected. Which LPAR attribute is the likely cause for the excess in memory consumption?. Active memory expansion factor. Maximum Virtual Adapters. Maximum memory. Maximum pages.

When updating a device attribute utilizing the -P flag with the chdev command, which of the following is true?. The device attribute will be updated for the parent of the device specified. The device attribute is updated forcibly and will result in the device changing to the defined state. The device attribute is updated immediately and will not be maintained after the next system boot. The device attribute is updated only in the ODM and does nottake affect until after the next system boot.

Which of the following statements is true about using crontab and at to execute tasks?. Commands scheduled with crontab are executed by at. Both commands can be used to schedule a weekly task to run for a user. User access control for both commands can be managed with .deny files in /var/adm/cron. Both commands preserve the current environment, including the user ID and current working directory.

Consider the following screen capture. The administrator needs to add 512 MB of space to the /db2/db2sp1 filesystem. What must be done before the administrator will be able to add this disk space to the filesystem?. Extend the upper bound of the logical volume. Increase the logical volume size first by 512 MB. Add another disk to the exevg volume group and migrate partitions. Increase the number of logical partitions the logical volume can hold.

What speed and duplex attributes should configured on a virtual Ethernet adapter?. 1000/Full. Auto/Auto. 10000/Full. Default/Default.

Which file needs to be modified to export a NFS file-system as read-only?. /etc/xtab. /etc/rmtab. /etc/security/exports. /etc/exports.

In the graphic below, the LPAR's current physical and virtual processor allocation matches its desired settings How do these settings limit system processor assignment for the LPAR?. The LPAR can increase to 16.00 processing units of capacity in the shared processing pool as needed. The LPAR will be able to use a maximum of 6.0 processing units of capacity in the shared processing pool. The LPAR will be able to use a maximum of 4.0 processing units of capacity in the shared processing pool. The administrator will be allowed to add a maximum of 4.0 additional processing units to the LPAR using DLPAR, making its allocation 6.0 processing units.

The following verification routine is part of a script used to automate cloning rootvg. This routine determines which disks are available for use. Applying the logic, what configuration of disk would be selected by the script as a candidate?. A SAN disk virtualized by NPIV. A local physical SAS drive, currently a member of the vg00 volume group. A physical SATA disk drive, currently containing the altinst_rootvg volume group. A SAN disk virtualized as a Virtual SCSI disk, currently not part of a volume group.

An administrator saved a change to the active profile of an LPAR. When will the change takeeffect?. Immediately after the profile is saved. When the admin reboots the LPAR from within AIX. When the Rebuild Managed System task completes. When the LPAR is shutdown and the profile is activated from the HMC.

In addition to enabling remote command execution, which task highlighted in the graphic below must be visited to enable an administrator with hmcoperator permissions to run HMC commands from another server using ssh?. "Change Network Settings" to open pott 22. "Remote Operation" to indicate that this HMC can beoperated from a remote host. "Remote Virtual Terminal" to enable virtual terminal connections for remotely connected HMC. "Manage Task and Resource Roles" to give the hmcoperator task role permission to ssh to the HMC from a remote host.

A customer has been creating LPARs on a new POWER8 system. After successfully activating the first 10 LPARs, the customer notices that the available RAM on physical machine reported by the HMC has reduced more than the sum of the memory currently allocated to the activated LPARs. The Customer appreciates there will be a memory overhead for each activated LPAR, but the overhead appears more than expected. Which LPAR attribute is the likely cause for the excess in memory consumption?. Active memory expansion factor. Maximum Virtual Adapters. Maximum memory. Maximum pages.

An administrator has logged in as root but is unable to run the ksh script named rperf. Given the following information, how could this be fixed?. Change the parent directory to be executable. Change the owner of the script to root. Changethe file to be of extension ksh. Change the permissions to 700.

Which RAID technology will provide the maximum data protection and available storage for a system with 6 physical disks?. RAID 0 (striping). RAID 1 (mirroring). RAID 5 + Hot Spare (striping + parity + spare). RAID 6 (striping + double parity).

Which parameter of the mkwpar command results in the created Versioned WPAR being mobility aware?. -c. -m. -lam. -ma.

How can ssh access for root be disabled?. Remove the ssh line from /etc/inetd.conf. Set rlogin to false in /etc/security/user for root. Set PermitRootLogin to no in /etc/ssh/sshd_config. Set RootPasswordAuthentication to no in /etc/ssh/ssh_config.

From which location can an administrator update system firmware?. The Systems Management menu on the ASMI. The IBM Support directory in the service partition. The Updates menu on the HMC. The NIM server update menu.

In which two ways can the pre-login message for an AIX LPAR be changed? (Choose two.). Issue thechsyscommand. Edit the /etc/security/login.cfg file. Change the /etc/motd file. Use thechseccommand. Modify the /etc/security/environ file.

How can an administrator disable Role Based Access Control (RBAC) in a WPAR?. Run chattr -E -I sys0 -a enhanced_RBAC=false Reboot the WPAR. Run the RBAC wizard and deselect 'Enable RBAC Reboot the system. Run chdev -I mywpar -a enhanced_RBAC=false Reboot the Global Environment. Run chwpar -a RBAC=false Reboot the WPAR.

With regard to planned maintenance, which statement about interim fix management is correct?. The interim fix must be manually committed prior to applying the updates. The interim fix will be automatically committed as part of the update process. If the fileset associated with interim fix will not be updated, it still needs to be temporarily rejected. If the updates include the official APAR, the update_all process will automatically uninstall the interim fix.

A failed disk has been replaced. The administrator wants to purge the references to the failure from the AIX error. The errors reported had an SRN of 16F35C72. How can the old errors be removed from the error log?. errpt-d-j 16F35C72. errclear-j 16F35C72. errlogger-r-j 16F35C72. errmsg-d-j 16F35C72.

What is the purpose of using tape drive special files?. To specify an action during certain tape operations. To eject tapes at the end of a tape operation. To configure alternate pathing of tape devices. To enable the tape SCSI Device Driver for a device.

A system administrator wants to create a server with network redundancy and maximum I/O throughput over two Ethernet cards. Which option will support the requirement?. Create an 802.3ad Link Aggregation adapter backed by both Ethernet cards and cable to a switch with 802.3ad enabled ports. Create a Network Interface Backup (NIB) with each Ethernet card being cabled to a different switch. Create the file /etc/sysconfig/network-scripts/ifcfg-bond0 then edit the two ifcfg-ethX configuration files to add a master or slave option. Cable to two switches and use 802.3ad enabled ports. Create a virtual adapter and assign it to the server, use both Ethernet adapters as backing devices to the virtual adapter with the mkvdev command. Have each adapter cabled to separate switches.

An administrator would like to enable operators to list the submission times of all crontab files, but not to edit them. How can this be accomplished?. Enable them to use the crontabcommand with Role Based Access Control (RBAC). Enable them to use the cronadm command with SUDO. Enable them to view the /var/spool/cron/log file with unix file permissions. Enable them to use the Iscrontab command by adding them to the system group.

The/app1 filesystem in appvg did not mount due to a failure replaying jfslog1. Which command will reinitialize jfslog1?. resysnclvodm –vjfslog1. logform/dev/jfsiog1. synclvodm appvg jfslog1. format-d/dev/jfslog1.

What must be done to change the default AIX login screen, which is displayed before the login prompt, when a system is accessed using telnet?. Add the desired text to the /etc/motd file. Edit the herald field in the /etc/security/login.cfg file. Update the MESG environment variable in /etc/environment. Add the LC_FASTMSG environment variable to /etc/profile.

How can administrators ensure that the Integrated Virtual Ethernet (IVE) adapters in their servers have the latest available firmware?. By upgrading the given IBM Power Systems server to the latest available system firmware. By using inventory scout to query the installed firmware level against the available level. By using either the managing HMC, SDMC or IVM to query and update the adapter firmware. By using the Ismcode AIX command with the query flag.

What is required to support VLANs in an AIX partition?. IEEE 802.1Q compatible adapter. Promiscuous mode disabled. IEEE 802.3ad compatible interface. QoS must be enabled.

An administrator has used setsecattr to associate authorizations with an AIX commanD. The appropriate stanza has been added to the privileged commands database (/etc/security/privcmds). What must be done before the new authorization can be used?. Run the setkst command to update the kernel security tables. Assign a new role that the authorization can be associated with and reboot. Activate the change in the security database with the updateauths command. Run the refreshsrc -g RBAC command to make the changes effective.

An administrator has issued the command to start IBM Systems Director server. The administrator wants to view the changing status to see when it becomes active. How can this be accomplished?. smcli-check. Isdstat-m. smstatus-r. Iwistat-c.

A NIM server is used to support different AIX Technology Levels among several clients. Each technology level is maintained in a separate lpp_source. Which command(s) will display what AIX fixes are available for several TL levels supported by a NIM server?. niminv-o fixget-a targets=lpp_source1,lpp_source2. nim_update_check-lsumalpp_source1 nim_update_check-lsumalpp_source2. nim-o cust-a fixes=update_all lpp_source1Jpp_source2. nim -o Ippmgr-a Ippmgr_flags="Isb" lpp_source1, Ipp_source2.