CREAR TEST

TEST BORRADO, QUIZÁS LE INTERESE: cambio de rango

COMENTARIOS	ESTADÍSTICAS	RÉCORDS

REALIZAR TEST

Título del Test: cambio de rango Descripción: Son preguntas para generar un cambio en tu vida Autor: ANONIMO OTROS TESTS DEL AUTOR Fecha de Creación: 05/09/2024 Categoría: Arte Número Preguntas: 99

COMPARTE EL TEST

COMENTAR

No hay ningún comentario sobre este test.

Temario:

Make sure that the chocks are in the correct position and make sure that there is no equipment below the aircraft which can cause damage. The weight of the fuel can suddenly compress the landing gear and lower the aircraft What is a synonym of "below"? A. On top B. Behind C. Above. FUEL SYSTEM WARNING: DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUEL ON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSE FIRE. Do not let the tanker go near the aircraft until the anti- collision lights have been set to OFF. It is very dangerous to be close to the aircraft in this situation. The best definition for the word "near" is: A. Close to an object B. Far from an object C. Distant from an object. Put the segments in order A. to refuel with / one engine running in an emergency / it is permitted B. in an emergency / it-is permitted / to refuel with / one engine running C. it is permitted/ in an emergency /one engine running to refuel with. Removal of the Door Actuator CAUTION: USE A SECOND WRENCH TO APPLY COUNTERTORQUE TO THE UNION WHEN YOU DISCONNECT/CONNECT HYDRAULIC LINES ON UNIONS, IF YOU USE THE SECOND WRENCH, YOU WILL NOT LOOSEN OR TIGHTEN THE UNION TOO MUCH. What is the purpose of using a second wrench? To give the appropriate tightening to the unions. To avoid tightening the union To keep the union more loosen. Inspection of the Oil Level CAUTION: IF YOU DRY-MOTOR THE ENGINE, MAKE SURE THAT THE OIL LEVEL IS STABLE BEFORE YOU DO THE INSPECTION. IN AMBIENT AIR TEMPERATURES OF LESS THAN 20°C, THE OIL LEVEL WILL BECOME STABLE ONLY AFTER 30 MINUTES. THUS THE LEVEL INDICATIONS ON THE SIGHTGLASS WILL NOT BE CORRECT BEFORE THE END OF THIS PERIOD. IF YOU ADD OIL WHEN IT IS NOT NECESSARY, THERE IS A RISK THAT YOU WILL CAUSE FAILURE OF THE IDG. What requirement do you have to fulfill if you dry motor the engine? The level indication on the sight glass will not be accurate before the oil levei becomes stable. The oil level has to be stable during the inspection The oil level becomes stable after 30 minutes if the ambient air temperature is less than 20°C. Inspection of the oil level with or without dry motoring. CAUTION: IF YOU DRY-MOTOR THE ENGINE, MAKE SURE THAT THE OIL LEVEL IS STABLE BEFORE YOU DO THE INSPECTION. IN OF LESS THAN 20°C, THE OIL LEVEL WILL BECOME STABLE ONLY AFTER 30 min Temperatures ambient air Ambient air temperatures Air temperatures ambient. NOTE: Bonding is mandatory. For grounding you must obey the local area regulations. Move all the equipment and material which is not necessary for the refuel/defuel procedure out of the safety area. On the panel 400VU, make sure that the ACCU PRESS on the triple indicator has sufficient pressure. If necessary, pressurize the yellow hydraulic system. best definition for the word "sufficient" is: To apply less pressure To apply more pressure To have enough pressure. NOTE: Bonding is mandatory. For grounding you must obey the local area regulations. Move all the equipment and material which is not necessary for the refuel/defuel procedure out of the safety area. On the panel 400VU, make sure that the ACCU PRESS on the triple indicator has sufficient pressure. If necessary, pressurize the yellow hydraulic system. The best word to describe the contrary of "obey" is: To oppose To comply with Leak. Make sure that the electrical equipment you use will not cause a Spark Slip Leak. _____The BRT, DIM1 or DIM2 pushbutton a second time, switches off the associated integral light and the corresponding ENTRY Area Lighting Pressed Pressing Press . During the refuel/defuel procedure, do only____ essential aircraft maintenance and/or servicing that will not. cause a spark you are not permitted to remove, install or test use the microphone on the High Frequency (HF) transmitter. During a Passenger Oxygen System Inspection of an AIRBUS A320 aircraft, it was noted that one Oxygen Generator was missing in one of the passenger rows, and only the oxygen masks were inside the container. This Bulletin is intended as preventive measure all personnel about this finding in order the awareness and that Passenger Oxygen System is reliable prior to aircraft delivery. A. To make sure, to increase, to communicate B. To communicate, to increase, to make sur C. To communicate, to make sure, to increase . Let the oil in the IDG become stable. Look at the of the IDG: - if the oil level is at or near the top of the green band, oil servicing is not necessary. - if the oil level is below the green band, do the steps 4.A thru 4.D. again. - if the oil level is above the green band, do the steps 4.A. and 4.C. again. Select the right option to complete the sentence above. Select one: Glass sight level oil Glass level oil sight Oil level sight glass. The DC electrical system___ supplied from the AC electrical system or from the batteries as a backup source. Select one: Was Will be IS. Installation of self-locking nuts When the fasteners (screws/nuts) are installed on uncured interfay sealant, the fasteners can lose their preload after curing because the sealant does not flow immediately. This is why you must tighten them again. The first tightening is got when the outer hexagonal part is sheared off. What happens when screws or nuts are installed on uncured interfay sealant? Select one: they lose their sealant preload after curing sealant does not flow so you need wait some time to tighten again it takes longer to cure so you need to cure again. IDG is installed on the associated engine accessory gearbox. Select one: Each both Many. FUEL SYSTEM WARNING: DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUEL ON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSE FIRE. What is the consequence of spilling fuel on hot engines or brakes? Select one: It can cause an explosion It can cause a hot environment It can cause a fire. Refuel/Defuel Safety Procedures for use in the Hangar WARNING: OBEY THE FUEL SAFETY PROCEDURES. __the equipment which is not necessary for the refuel/defuel procedure from between the aircraft and the hangar exit. Choose the correct word to fill in the space in blank. Select one: Put back Replace Remove. Select the correct order. flush away / or remove / fuel leakage / with water with water / flush away / fuel leakage / or remove flush away / or remove / with water / fuel leakage. Do not let the tanker go near the aircraft until the anti-collision lights have been set to OFF. Before you start the refuel/defuel procedure make sure that all the electrical circuits in the fuel system are complete and do not spill fuel on the engines or the brakes. If you spill fuel on engines or brakes that are hot, it can cause fire. The definition for the word "before" is: Select one: Prior to Soon Later in time. Make sure that, if there is an you can move the fuel tanker/pump unit and the other equipment away quickly. Select one: Emergency Operation Misfortune. Make sure that the overboard vent lines are not___ If there is obstruction, damage to the fuel tanks can occur. Select one: Operate In position Blocked. cockpit was removing the nuts; the speeder tool slipped causing a windshield glass ply cracking. PREVENTIVE ACTIONS: -Do not use speeder tool for windshield removal, this tool represents a risk since it must be held with both hands, reducing any grip to the aircraft or platform structure. A ratchet wrench or alternative tool should be used. or fasteners that cannot be easily removed, use the fastener removal tool or applicable. Which of the following is TRUE? Select one: A speeder tool can reduce the risk of falling from the aircraft or platform structure. A speeder tool can be used if the person holds it with both hands. A fastener removal tool can be used to remove fasteners that cannot be easily removed. Select the correct order. Select one: it is permitted / in an emergency / one engine running / to refuel with in an emergency / to refuel with / one engine running / it is permitted in an emergency / it is permitted / to refuel with / one engine running. Installation of self-locking nuts Procedure for the installation of self- locking nuts with interfay sealant. When the fasteners (screws/nuts) are on uncured interfay sealant, the fasteners can lose their preload after_ _ because the sealant does not flow immediately. This is why you must _them again. The first tightening is got when the outer hexagonal part is sheared off. Choose the correct actions, word and verb forms for this text. Select one: installed, cured, tightened installed, curing, tighten installed, cure, tightening. Emergency Generator can supply part of the AC and DC electrical systems in case of loss of normal supply. Select one: Many An A. During the refuel/defuel procedure do not ____ the aircraft external lighting Select one: Operates Operating Operate. The cabin attendant work lights consist of__ intensity lights installed in an overhead panel above the attendant seats. Select one: high Most high Highly. Put the segments in order. Select one: You must / complete / a normal / APU shutdown You must / a normal / APU shutdown / complete Complete F you must APU shutdown a normal. Refuel/Defuel Safety Procedures for use in the Hangar WARNING: OBEY THE FUEL SAFETY PROCEDURES._____ The safety barriers and the NO SMOKING warning notices at all the hangar entrances. To be prepared to tow the aircraft out of the hangar for an emergency. Remove the equipment which is not necessary for the refuel/defuel procedure from between the aircraft and the hangar exit Choose the correct word to fill in the space in blank Select one: Make sure Put Keep. Refuel/Defuel Safety Procedures for use in the Hangar WARNING: OBEY THE FUEL SAFETY PROCEDURES.___ all the hangar doors. Do not close the hangar doors until you have completed the refuel/defuel procedure. Make the limits of the safety área the limits of the hangar Choose the correct words to fill in the space in blank Select one: Make sure Attach Open. DC NORMAL GENERATION The two (BAT 1and BAT 2) and the two main Transformer Rectifiers (TR1 and TR2) are located in DC EMERGENCY GENERATION Select one: Batteries Battery Batterys. During the refuel/defuel procedure do not fill the oxygen system or__the oxygen bottles one: Change Intlate Turn. They are called attention getters Select one: UPPER ECAM, LOWER ECAM MASTER WARNING, MASTER CAUTION PRIMARY FLIGHT DISPLAY, NAVIGATION DISPLAY. They are electrically heated Select one: pitot probe, static port, leading edge AOA sensor, drain mast, windshield UPPER ECAM, LOWER ECAM. THEY ARE N2 COMPONENTS Select one: HP ROTOR, HIGH PRESSURE TURBINE, HIGH PRESSURE COMPRESSOR, FAN LP TURBINE, LP COMPRESSOR, FAN, LP SHAFT HP COMPRESSOR, HIGH PRESSURE TURBINE, HIGH PRESSURE SHAFT. FUEL SYSTEM WARNING: DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUEL ON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSE FIRE. On the panel 400VU, make sure that the ACCU PRESS on the triple indicator has sufficient pressure. If necessary, pressurize the yellow hydraulic system The best definition for the Word "sufficient" is: Select one: To apply less pressure To apply more pressure To have enough pressure. ___________ during refuel/defuel operations. Select one: Do not use the microphone on the High Frequency (HF) transmitter Essential aircraft maintenance and/or servicing that will not cause a spark ls displayed on the flight deck. During the refuel/defuel procedure ____ not use the aircraft external lighting. Select one: to do does do. Make sure that the ventilation air flow is sufficient to work safely, _______ use a respirator. Select one: nevertheless further otherwise. Make sure that the fuel tanker (or hydrant)___the correct fuel. The correct fuels are shown in the Flight Manual Select one: Performs Have Contains. What does FAC stand for? Select one: Flight angle computer Flight augmentation computer . Full augmentation computer. What does PA stand for? Select one: passenger aircraft primary announcement passenger address. It comes on in amber colour Select one: MCDU MASTER WARNING MASTER CAUTION. It comes on in red colour Select one: MASTER CAUTION ECAM MASTER WARNING. They are called attention getters Select one: UPPER ECAM, LOWER ECAM PRIMARY FLIGHT DISPLAY, NAVIGATION DISPLAY MASTER WARNING, MASTER CAUTION. They are electrically heated Select one: pitot probe, static port, leading edge AOA sensor, drain mast, windshield LP TURBINE, LP COMPRESSOR, FAN, LP SHAFT. THEY ARE N COMPONENTS Select one: HP ROTOR, HIGH PRESSURE TURBINE, HIGH PRESSURE COMPRESSOR, FAN LP TURBINE, LP COMPRESSOR, FAN, LP SHAFT HP COMPRESSOR, HIGH PRESSURE TURBINE, HIGH PRESSURE SHAFT. FUEL SYSTEM WARNING: DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUEL ON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSE FIRE. On the panel 400VU, make sure that the ACCU PRESS on the triple indicator has sufficient pressure. If necessary, pressurize the yellow hydraulic system The best definition for the Word "sufficient" is: Select one: To apply less pressure To apply more pressure To have enough pressure. FUEL SYSTEM WARNING: DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUEL ON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSE FIRE. Do not let the tanker go near the aircraft until the anti-collision lights have peen set to OFF. It is very dangerous to be close to the aircraft in this situation The best definition for the word "near" is: Select one: Far from an object Distant from an object Close to an object. FUEL SYSTEM WARNING: DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUEL ON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSE FIRE. What is the consequence of spilling fuel on hot engines or brakes? Select one: It can cause a fire It can cause a hot environment It can cause an explosion. During the refuel/defuel procedure, do only ______ Select one: use the microphone on the High (HF) transmitter. you are not permitted to remove install or test. essential aircraft maintenance and/or servicing that will not cause a spark. ___________ during refuel/defuel operations. Select one: Do not use the microphone on the High Frequency (HF) transmitter Essential aircraft maintenance and/or servicing that will not cause a spark ls displayed on the flight deck. During the refuel/defuel procedure ____ not use the aircraft external lighting. Select one: to do does do. During the refuel/defuel procedure do not fill the oxygen system or __the oxygen bottles Select one: Change Intlate Turn. Refuel/Defuel Safety Procedures for use in the Hangar WARNING: OBEY THE FUEL SAFETY PROCEDURES. ___ all the hangar doors. Do not close the hangar doors until you have completed the refuel/defuel procedure Make the limits of the safety area the limits of the hangar. Select the correct option to complete the sentence. Select one: Open Attach Make sure. Make sure that the overboard vent lines are not_. If there is obstruction, damage to the fuel tanks can occur. Select one: Blocked Operate In position. Make sure that the ventilation air flow is sufficient to work safely, _______ use a respirator. Select one: nevertheless further otherwise. Make sure that the fuel tanker (or hydrant)___the correct fuel. The correct fuels are shown in the Flight Manual Select one: Performs Contains Have. Make sure that, if there is an you can move the fuel tanker/pump unit and the other equipment away quickly Select one: Emergency Operation Misfortune. What does FAC stand for? Select one: Flight angle computer Flight augmentation computer Full augmentation computer. What does PA stand for? Select one: passenger aircraft primary announcement passenger address. It comes on in amber colour Select one: MCDU MASTER WARNING MASTER CAUTION. It comes on in red colour Select one: MASTER CAUTION ECAM MASTER WARNING. Reverse is manually selected by the flight crew by__ the latching levers on the throttle control levers. Select one: lifted lifting lift. Do not refuel the aircraft if a fire or engine over heat warning _______ Select one: You are not permitted to remove, install or test Essential aircraft maintenance and/or servicing that will not cause a spark ls displayed on the flight deck. Do not ___ the aircraft main engines during a refuel/defuel procedure. Select one: Perform Fly Operate. Do not let the tanker go near the aircraft until the anti-collision lights have been set to OFF. Before you start the refuel/defuel procedure make sure that all the electrical circuits in the fuel system are complete and do not spill fuel on the engines or the brakes. If you spill fuel on engines or brakes that are hot, it can cause fire The best definition for the Word "spill" is: Select one: To fall out of a container To check the inside of a container To put into a container. Do not let the tanker go near the aircraft until the anti-collision lights nave been set to OFF. Before you start the refuel/defuel procedure make sure that all the electrical circuits in the fuel system are complete and do not spill fuel on the engines or the brakes. If you spill fuel on engines or brakes that are hot, it can cause fire. The definition for the word "before" is: Select one: Prior to Soon Later in time. The EEC manages engine thrust and protects against overspeed and overtemperature by controlling the engine sub-systems. What is the meaning of OVERSPEED? Select one: more speed Excess in speed less speed. The system provides illumination of lavatory lighted signs. _call lights to indicate the location from which a passenger call is initiated. Individual reading lights are installed. Select one: There are There is There was. The emergency lights ______ automatically as soon as they sense smoke Select one: Come on Turn on Energize. Two sets of pedals _____ mechanical control. the rudder Select one: enable disable unable. The Refuel/Defuel panel is located. Select one: on the right hand side of the fuselaje in the belly fairing on the center of the fuselage in the belly fairing. on the left hand side of the fuselaje in the belly fairing. The cabin attendant work lights consist of__ intensity lights installed in an overhead panel above the attendant seats. Select one: Most high high Highly. The DC electrical system supplied from the AC electrical system or from the batteries as a backup source Select one: Is Will be Was. The HP compressor is also the ______of customer bleed air. Select one: mean form source. The accessory gearbox is located at the bottom of the fan case and is driven by the HP rotor through the Angle gearbox. The fuel pumps, oil pumps, hydraulic pump, Integrated Drive Generator (IDG) and dedicated alternator are all driven by the gearbox. During engine starting, the starter rotates the HP compressor through the gearboxes What motors the gearbox? Select one: the IDG the gearbox the high pressure rotor . The A321 fuel tanks are integrated into the center fuselage area and the wings. Like the A318/A319/A320, the center tank is part of the center wing box but unlike the A318/A319/A320, the wing tanks are not divided. The tanks are simply called left and right wing tanks which is the correct statement? Select one: on the A321, the centre tank is part of the wing box on the A320 the wing tanks are not divided on the A321, the trim tank is available. The accessory gearbox is located at the bottom of the fan case and is driven by the HP rotor through the Angle gearbox. The fuel pumps, oil pumps, hydraulic pump, integrated drive generator and dedicated alternator are all driven by the gearbox. During engine starting, the starter rotates the HP compressor through the gearboxes. What rotates the IDG? Select one: the HP compressor the gearbox the rotor. The 4-stage booster compressor is located ir the intermediate case. The booster supplies air to the engine core. This is primary airflow. The LP rotor (N1) is made of the fan and the booster compressor driven by the LP turbine. The intermediate case is also the location for the _________ Select one: fwd engine turbine forward engine mount forward engine compressor . On the panel 110VU, make sure that the PARK BRK is on. If the Main Landing Gear (MLG) doors are open during the refuel procedure: visually examine the tires and shock absorbers and make sure you will have sufficient clearance to the ground after the refuel is complete. What task you must perform if the MLG doors are open? Select one: Make sure the area is with enough clearance Make the visual inspection in the ground before the refuel Visually examine the tires and shocks. Put the segments in order. Select one: Put / NO SMOKING / warning notices / around / the work area Warning notices / NO SMOKING / put/ around / the work area Put / warning notices / NO SMOKING / around / the work área . Put the segments in order. Select one: flush away / fuel leakage /.or remove / with wáter with water / flush away / fuel leakage / or remove flush away / or remove / fuel leakage with water. Select the correct order. Select one: complete/you must/APU shutdown/a normal you must/ complete/ a normal/ APU shutdown APU shutdown/ you must/ complete a normal. Select the correct order. Select one: it is permitted / in an emergency/ one engine running / to refuel with in an emergency / to refuel with / one engine.running / it is permitted in an emergency / it is permitted / to refuel with / one engine running. Safety Precautions-Fuel System You must obey the Fuel Safety Procedures when you refuel/defuel an aircraft. Do not let the tanker go near the aircraft until the anti-collision lights have been set to OFF. Before you start the refuel/defuel procedure, make sure that all the electrical circuits in the fuel system are complete. Do not spill fuel. If you spill fuel on engines or brakes that are hot, it can cause fire. Move all the equipment and material which is not necessary for the refuel/defuel procedure out of the safety area. On the panel 400VU, make sure that the ACCU PRESS on the triple indicator has sufficient pressure. If necessary, pressurize the yellow hydraulic system How must the safety area be during refuel/defuel procedure? Select one: Clean and clear of distractions Clear of non necessary material an anninmant An obligation or command to follow. Safety Precautions: You must obey the Fuel Safety Procedures when you refuel/defuel an aircraft and do not let the tanker go near the aircraft until the anti-collision lights have been set to OFF. The word "must" refers to: Select one: A recommendation An obligation or command to follow An action to occur in future. Safety_Precautions Fuel System If the Main Landing Gear (MLG) doors are open during the refuel procedure: Examine visually the tires and shock absorbers Make sure you will have sufficient clearance to the ground after the refuel is complete Make sure that the chocks are in the correct position and make sure there is no equipment below the aircraft which can cause damage What task must you perform if the MLG doors are open? Select one: Check only the chock absorbers visually There should be equipment below the aircraft. Have enough clearance to the ground after the refuel is complete. NOTE: Bonding is mandatory. For grounding you must obey the local area regulations. Move all the equipment and material which is not necessary for the refuel/defuel procedure out of the safety area. On the panel 400VU, make sure that the ACCU PRESS on the triple indicator has sufficient pressure. If necessary, pressurize the yellow hydraulic system. The best word to describe the contrary of "obey" is: Select one: To oppose To comply with To be ruled by. NOTE: Before you do a check of the oil level, we recommend that you do dry motoring for two minutes. Alternatively, you can do the check after an engine run at minimum idle. This is to make sure you get maximum filling of the_ _. Select the right option to complete the sentence above. Select one: External oil system External system oil Oil external system. Drain the engine oil system as follows: ____________the oil tank ____________a clean container mínimum capacity 10 USgal (40 I) below the oil tank to catch the drained oil. ___________the oil filler cap. ___________the oil tank drain plug (10) from the front flange of the gearbox (below the oil pressure pump). Choose the right verbs to fill in the spaces Select one: Drain - Remove - Put-Loosen Drain - Put - Loosen 1 Remove Drain - Put Tighten – Remove. ______ you start the refuel/defuel procedure, make sure that these are available:  a fueling supervisor or fueling safety person  The correct fire-fighting equipment  approved persons to use the fire-fighting equipment. Select one: After During Before. As in the V-2500 the fan assembly has and supplies most of the engine thrust. Select one: 25 wide-chord blades 29 wide-chord blades 22 wide-chord blades. In order to increase engine reliability and efficiency, the Full Authority Digital Engine Control (FADEC) gives the full range of engine control to achieve steady state and transient engine performances when operated in combination with aircraft subsystems What does steady mean? Select one: solid to be ready not changing. Filling_of the IDG with Oil NOTE: Look at the oil level sightglass of the IDG: The oil level must be at or near the line between the yellow band and the green band and if the oil level is below this position, do the normal procedure of oil replenishing to adjust the oil level. Where should the oil level be? Select one: Above the position of the line petween the yellow band and the Green band. below or close to the line between the yellow band and the green band. At the line between the yellow band and the Green band. Adjustment of The Doors Latch Rollers & Fittings This bulletin is intended to request MaintenancePersonnel of the removal of any residues of modeling clay (Play-dough) on the door latch fittings and to clean the working area, after the adjustment procedure of the doors latch roller and Fittings is completed. These steps must be made once the clearance between the latch foller and the outboard face of the latch fitting has been determined to be within the limits in accordance with the work document being used (Customer Job cards and/or AMM). What is the correct order of this procedure? Select one: removal of residuals, clean the work area, adjustment of procedure adjustment procedure, removal of residues, clean the work area adjustment procedure, clean the work area, removal of residuals. CONTROL PANELS The FUEL control panel is located on the overhead panel. The A321 FUEL control panel is very similar to the A318/A319/A320, except: the fuel transfer link between the center and wing tanks is indicated, - CTR TK XFR is indicated instead of CTR TK PUMPS. Which statement is correct? Select one: The fuel transfer link centre to wing on the A319 reads CTR TK XFR The control panel on the A320 looks almost the same as in the A321. The fuel transfer link centre to wing on the A321 reads CTR TK PUMPS . from the door actuator as follows: Remove the electrical connector from the receptacle of the proximity switch, put blanking caps on the disconnected electrical connectors, remove the bonding jumpers and from the door actuator as follows: Remove the screw, the washer, the nut and disconnect them bonding jumper from the bonding angle of the eye-end, then, remove the screw and the washer and disconnect the bonding jumper from the door actuator. When do you remove the bonding jumpers from the door actuator? Select one: During the disconnection of the bonding jumper. Before you remove the screw, the washer and the nut. After you disconnect the electrical connector form the actuator.

Denunciar Test