Which key chain is being used for authentication of EIGRP adjacency between R4 and R2? CISCO EIGRP KEY MDS.
How route tags can be set?(choose two) ONLY within route tags within tag lists can be set with ONLY route-maps can be set DIRECTLY within route maps. only used on link state RPs.
What does stateful NAT64 do that stateless NAT64 does not do? A.Stateful NAT64 maintains bindings of IPv4 to IPv6 link-local addresses. B.Stateful NAT64 translates IPv4 to IPv6. C.Stateful NAT64 translates IPv6 to IPv4. D.Stateful NAT64 maintains bindings or session state while performing translation.
What is the default authentication in RIPv2 when authentication is enabled? A. enable password authentication B. MD5 authentication C. SHA1 authentication D. plaintext authentication.
Which task must you perform to enable a point-to-point Frame Relay connection? A. Enable inverse ARP. B. Configure the encapsulation type. C. Configure static address mapping. D. Disable inverse ARP.
Which condition prevents the establishment of a DMPVN tunnel between two spokes? A. The two spokes have different tunnel keepalive settings B. HSRP is enabled on the spoke devices C. IPsec is enabled on the spoke devices D. The two spokes are behind different PAT devices.
R1 is configured with VRF-Lite and can ping R2. R2 is fully configured, but it has no active
EIGRP neighbors in vrf Yellow. If the configuration of R2 is complete, then which issue prevents the EIGRP100
neighbor relationship in vrf Yellow from forming? A.The no auto-summary command is preventing the EIGRP neighbor relationship from forming B. There is a Layer 1 issue that prevents the EIGRP neighbor relationship from forming C. The interface IP addresses are not in the same subnet D. EIGRP 100 network 192 168 1 0/24 is configured in the global routing table on R1.
Where can NetFlow export data for long term storage and analysis? A. another network device B. syslog C. flat file D. collector.
What is the default maximum segment size for TCP traffic
536 1492 1500 1508 3340 4096.
Drag and drop the statements from the left onto the correct uRPF modes on the right It can drop legitimate traffic it requires the source address to be routable It support using the default route as a route reference it permits only packets that are received on the same interface as the exit interface for the destination address .
In which state do DR and BDR establish adjacency with each ospf router in the network A. Exstart State B. Loading State C. Exchange State D. Init State.
In which two areas does OSPF send a summary route by default? (Choose two.) A. NSSA B. backbone C. stub D. normal F. totally stubby.
TCP traffic is blocked on port 547 between a DHCPv6 relay agent and a DHCPv6 server that is configured for prefix delegation. Which two outcomes with result when the relay agent is rebooted? (Choose two.) A. Hosts will not obtain DHCPv6 addresses B. The DHCPv6 relay agent will resume distributing addresses C. DHCFM3 address conflicts will occur on downstream clients D. Routers will not obtain DHCPv6 prefixes. E. DHCPv6 clients will be unreachable.
Which two statements are true of the OSPF link-state routing protocol? (Choose two.)
A. Using the Bellman-Ford algorithm, each OSPF router independently calculates its best paths to all destinations in the network. B. Using the DUAL algorithm, each OSPF router independently calculates its best paths to all destinations in the network. C. OSPF sends summaries of individual link-state entries every 30 minutes to ensure LSDB synchronization. D. OSPF sends triggered updates when a network change occurs E. OSPF sends updates every 10 seconds F. When a link changes state, the router that detected the change creates a link-state advertisement (LSA) and propagates it to all OSPF devices using the 224.0.0.6 multicast address.
which phase of dmpvn spoke to spoke communications? A. phase2 B. phase4C C. phase5 D. phase6 E. phase1.
Which SNMP model and level can provide DES encryption? SNMPV2noAuthNoPrry SNMPv3authNoPriv SNMPv3 authEn SNMPv3noAuthNoPrv.
With which network type will OSPF establish router adjacencies but not perform the DR/BDR election A. Point-to-point B. Backbone area 0 C. Broadcast multi-access D. Non-broadcast multi-access.
In which scenario can asymmetric routing occur? active/standby firewall setup active/active firewall setup redundant routers running VRRP single path in and out of the network.
A network engineer is unable to make VRF lite EIGRP adjacency work.There is nothing wrong with communication between R1 and R2. What command will eliminate the issue when executed on both routers? A. (config-router-af)# autonomous-system 100 B. (config)# ip-multicast-routing C. (config-vrf)# route-target both 100:1 D. (config-router-af)# network 209.165.202.128 0.0.0.31.
How is authentication handled with OSPFv3? A. OSPFv3 for IPv6 authentication is supported by SHA-1 authentication. B. OSPFv3 for IPv6 authentication is supported by MD5 authentication C. OSPFv3 for IPv6 authentication is supported by IPv6 IPsec D. OSPFv3 for IPv6 authentication is supported by IPv4 IPsec.
Refer to the exhibit. Which command us used to control the type of routes that are processed in incoming route updates? A. passive-interface B. distribute-list 1 out C. distribute-list 1 in D. ip vrf forwarding.
Areas of Router 5 and 6 are not normal areas, inspect their routing tables and determine which statement is true? A. R5's Loopback and R6's Loopback are both present in R5's Routing table B. R5's Loopback and R6's Loopback are both present in R6's Routing table C. Only R5's loopback is present in R5's Routing table D. Only R6's loopback is present in R5's Routing table E. Only R5's loopback is present in R6's Routing table.
Which three causes of unicast flooding are true? (Choose three) A. excess space in the forwarding table B. changes in the STP topology C. consistent STP topology D. asymmetric routing F .symmetric routing E. forwarding table overflow.
Refer to the following:
aaa new-model
aaa authentication login default local-case enable
aaa authentication login ADMIN local-case
username CCNP secret Str0ngP@ssw0rd!
line 0 4
login authentication ADMIN
How can you change this configuration so that when user CCNP logs in, the show run command is executed
and the session is terminated? A. Add the autocommand keyword to the aaa authentication command B. Assign privilege level 15 to the CCNP username C. Add the access-class keyword to the aaa authentication command D. Assign privilege Ievel14 to the CCNP username E. Add the access-class keyword to the username command F. Add the autocommand keyword to the username command.
How old is the Type 4 LSA from Router 3 for area 1 on the router R5 based on the output you have examined? A. 1858 B. 1601 C.600 D. 1569.
Question 47 new and old 25 A. remaining key lifetime B. path MTU C. invalid identity packets D inbound crypto map E. tagged packets F. untagged packets.
Which three functionalities are specific to stateful NAT64? (Choose three.) A. It conserves IPv4 addresses. B. It requires IPv4-translatable IPv6 addresses. C. No constraint is put on the number of endpoints due to 1:N translation. D. It helps ensure end-to-end address transparency and scalability. E. A state or bindings are created on every unique translation. F. It requires either manual or DHCPv6-based address assignment for IPv6 hosts. Answer: ACE.
Which task must you perform to implement EIGRP for IPv6 on a device? A. Use the ipv6 cef command to enable Cisco Express Forwarding on the device. B. Configure a loopback interface on the device. C. Manually configure the router ID
D. Statically configure a neighbor.
Refer to the exhibit.
For which reason is EIGRP failing to redistribute the default route? A. The EIGRP process is missing the default metric. command. B. The EIGRP process is missing the no auto-summary C. The EIGRP process is missing the router ID. D. The route-map statement is missing the match any keyword.
A network engineer enables OSPF on a Frame Relay WAN connection to various remote sites, but no OSPF
adjacencies come up. Which two actions are possible solutions for this issue? (Choose Two) A. Change the network type to point-to-multipoint under WAN interface. B. Enable virtual links. C. Change the network type to nonbroadcast multipoint access. D. Configure the neighbor command under OSPF process for each remote site. E. Ensure that the OSPF process number matches among all remote sites.
Which two routers can do OSPF route summarization?. (Choose Two) A. ABR B. ASBR C. Summary router D. internal router E. Backbone router.
What from the following can cause an issue for URPF? (this could be single answer or multiple choice) URPF FAIL
Reasons why urpf may fail: A. Asymmetric routing B. Cef not enabled C. Urpf not applied to the traffic source D. If it is used as ingress filtering.
Traffic from R1 to R61 s Loopback address is load shared between R1-R2-R4-R6 and R1-R3-R5-R6 paths.
What is the ratio of traffic over each path? 1:1 1:5 6:8 19:80.
Which statement about the metric calculation in EIGRP is true? A. The maximum delay along the path is used B. The mean value of bandwidth between the source and destination is used C. The minimum bandwidth between the source and destination is used D. The minimum delay along the path is used.
The OSPF which type of Router CAN BE aggregated? (Choose two) A. the ABR B. the ASBR C. Backbone Router D. Intra Router.
Where are EIGRP successor routes stored? A. In the routing table only B. In the neighbor table only C. In the topology table only D. In the routing table and the topology table E. In the routing table and the neighbor table.
Which OSPF network type uses a DR? A. Nonbroadcast multi-access B. point-to-point C. point-to-multipoint D. point-to-point nonbroadcast.
You need the IP address of the devices with which the router has established an adjacency. Also, the retransmit interval and the queue counts for the adjacent routers need to be checked. What command will display the required information? A. show ip eigrp adjacency B. show ip eigrp topology C. show ip eigrp interfaces D. show ip eigrp neighbor.
Which statement is true about EBGP? A. An internal routing protocol can be used to reach an EBGP neighbor. B. The next hop does not change when BGP updates are exchanged between EBGP neighbors. C. A static route can be used to form an adjacency between neighbors. D. EBGP requires a full mesh.
Which version or versions of NetFlow support MPLS? A. all versions of NetFlow B. NetFlow version 9 C. NetFlow version 8 D. NetFlow version 5 F. NetFlow version 8 and 9.
–options were little bit modifie
Which of the following are characteristics of TACACS+? (Choose two.) A. Uses UDP B. Encrypts an entire packet C. Offers robust accounting D. Cisco-proprietary.
Drag and drop each DMVPN in the left to the correct statement in the right. mGRE NHRP Hub Spoke.
Refer to the following command.
Logging Console 7
Which option is one of the effects entering this command on a Cisco IOS router, with no additional logging configuration? A. Debug messages can be seen on the console by enabling “terminal monitor” B. Debug messages are logged only on active console connections. C. A user that is connected via SSH sees level 7 messages D. The router can experience high CPU utilization.
What is the task you must perform when configuring SSH? (Choose two) A. Configure TACACS+ B. Configure hostname C. Generate RSA key D. Disable telnet.
Which two pieces of information can you determine from the output of the show ntp status command? A. The NTP version number of the peer B. The configured NTP servers C. The IP address of the peer to which the clock is synchronized D. Where the clock is synchronized.
You are implementing WAN access for an enterprise network while running applications that require a fully meshed network, which two design standards are appropriate for such an environment? (Choose two) A. A centralized DMVPN solution to simplify connectivity for the enterprise B. A dedicated WAN distribution layer to consolidate connectivity to remote sites C. A collapsed core and distribution layer to minimize costs D. Multiple MPLS VPN connections with static routing E. Multiple MPLS VPN connections with dynamic routing.
Which task do you need to perform first when you configure IP SLA to troubleshoot a network connectivity issue? A. Specify the test frequency B. Enable the ICMP echo operation C. Schedule the ICMP echo operation D. Verify the ICMP echo operation.
Which technology can combine multiple physical switches into one logical switch? A. HSRP B. VSS C. VRRP D. NHRP.
Which two features are compatible with port security? (Choose two) A. Voice VLAN B. SPAN source port C. DTP.
Which fallback method can you configure to allow all AAA authorization requests to be granted if the other methods do not respond or return an error? A. Radius B. Enable C. TACACS+ D. NONE.
By default what is the maximum number of equal metric path BGP uses for load balancing? A. 4 B. 6 C. 8 D. 16.
The track objects in IP SLA and make sure that it is only up if all track objects are up, which method achieves that goal? A. AND B. OR C. XOR D. NOT.
With PCA and PCB and there are three routers between them and a different MTU value and they want a PCA to run an application with PCB and DF is set so we have to choose? A. MSS B. PMTU C. GRE D. ?.
Drag and Drop
TLL ICMP Redirect ICMP unreachable.
How to implement local authentication using a list for case insensitive usernames? A. aaa authentication login default local B. aaa authentication login default local-case.
|
