A network engineer is configuring OSPF between router R1 and router R2. The engineer must ensure that a DR/BDR election does not occur on the Gigabit Ethernet interfaces in area 0. Which configuration set accomplishes this goal? R1(config-if)#interface Gi0/0
R1(config-if)#ip ospf network point-to-point
R2(config-if)#interface Gi0/0
R2(config-if)#ip ospf network point-to-point
R1(config-if)#interface Gi0/0
R1(config-if)#ip ospf network broadcast
R2(config-if)#interface Gi0/0
R2(config-if)#ip ospf network broadcast
R1(config-if)#interface Gi0/0
R1(config-if)#ip ospf database-filter all out
R2(config-if)#interface Gi0/0
R2(config-if)#ip ospf database-filter all out
R1(config-if)#interface Gi0/0
R1(config-if)#ip ospf priority 1
R2(config-if)#interface Gi0/0
R2(config-if)#ip ospf priority 1
.
Refer to the exhibit.
Which command when applied to the Atlanta router reduces type 3 LSA flooding into the backbone area and summarizes the inter-area routes on the Dallas router? Atlanta(config-route)#area 0 range 192.168.0.0 255.255.252.0 Atlanta(config-route)#area 1 range 192.168.0.0 255.255.252.0 Atlanta(config-route)#area 0 range 192.168.0.0 255.255.248.0 Atlanta(config-route)#area 1 range 192.168.0.0 255.255.248.0.
Refer the exhibit.
Which router is the designated router on the segment 192.168.0.0/24? Router Chicago because it has a lower router ID Router NewYork because it has a higher router ID This segment has no designated router because it is a nonbroadcast network type. This segment has no designated router because it is a p2p network type.
Refer to the exhibit.
Which command must be applied to R2 for an OSPF neighborship to form? network 20.1.1.2 0.0.255.255 area 0 network 20.1.1.2 255.255.255.255 area 0 network 20.1.1.2 0.0.0.0 area 0 network 20.1.1.2 255.255.0.0. area 0 network 20.1.1.0 0.0.0.0 area 0.
Which feature of EIGRP is not supported in OSPF? load balancing of unequal-cost paths load balance over four equal-costs paths uses interface bandwidth to determine best path per-packet load balancing over multiple paths.
Refer to the exhibit. An engineer attempts to configure a router on a stick to route packets between Clients, Servers, and Printers; however, initial tests show that this configuration is not working. Which command set resolves this issue? router eigrp 1
network 10.0.0.0 255.0.0.0
network 172.16.0.0 255.255.0.0
network 192.168.1.0 255.255.0.0
router eigrp 1
network 10.0.0.0 255.255.255.0
network 172.16.0.0 255.255.255.0
network 192.168.1.0 255.255.255.0
interface Vlan10
no ip vrf forwarding Clients
!
interface Vlan20
no ip vrf forwarding Servers
!
interface Vlan30
no ip vrf forwarding Printers
interface Vlan10
no ip vrf forwarding Clients
ip address 192.168.1.1 255.255.255.0
!
interface Vlan20
no ip vrf forwarding Servers
ip address 172.16.1.1 255.255.255.0
!
interface Vlan30
no ip vrf forwarding Printers
ip address 10.1.1.1 255.255.255.0
.
How does the EIGRP metric differ from the OSPF metric? The EIGRP metric is calculated based on bandwidth only. The OSPF metric is calculated on delay only. The EIGRP metric is calculated based on delay only. The OSPF metric is calculated on bandwidth and delay. The EIGRP metric is calculated based on hop count and bandwidth. The OSPF metric is calculated on bandwidth and delay. The EIGRP metric is calculated based on bandwidth and delay. The OSPF metric is calculated on bandwidth only.
Which OSPF network types are compatible and allow communication through the two peering devices? broadcast to nonbroadcast point-to-multipoint to nonbroadcast broadcast to point-to-point point-to-multipoint to broadcast.
Based on this interface configuration, what is the expected state of OSPF adjacency?
R1
interface GigabitEthernet0/1
ip address 192.0.2.1 255.255.255.252
ip ospf 1 area 0
ip ospf hello-interval 2
ip ospf cost 1
R2
interface GigabitEthernet0/1
ip address 192.0.2.2 255.255.255.252
ip ospf 1 area 0
ip ospf cost 500
Full on both routers not established 2WAY/DROTHER on both routers FULL/BDR on R1 and FULL/BDR on R2.
Refer to the exhibit. Which statement about the OPSF debug output is true?
R1#debug ip ospf hello
R1#debug condition interface fa0/1
Condition 1 set
The output displays all OSPF messages which router R1 has sent or received on interface Fa0/1 The output displays all OSPF messages which router R1 has sent or received on all interfaces The output displays OSPF hello messages which router R1 has sent or received on interface Fa0/1 The output displays OSPF hello and LSACK messages which router R1 has sent or received.
Which EIGRP feature allows the use of leak maps? offset-list neighbor address-family stub.
Which two statements about EIGRP load balancing are true? (Choose two) EIGRP supports 6 unequal-cost paths A path can be used for load balancing only if it is a feasible successor EIGRP supports unequal-cost paths by default Any path in the EIGRP topology table can be used for unequal-cost load balancing Cisco Express Forwarding is required to load-balance across interfaces.
Which statement about LISP encapsulation in an EIGRP OTP implementation is true? OTP uses LISP encapsulation for dynamic multipoint tunneling OTP maintains the LISP control plane OTP uses LISP encapsulation to obtain routes from neighbors LISP learns the next hop.
Which reason could cause an OSPF neighborship to be in the EXSTART/EXCHANGE state? Mismatched OSPF network type Mismatched areas Mismatched MTU size Mismatched OSPF link costs.
Which feature is supported by EIGRP but is not supported by OSPF? route summarization equal-cost load balancing unequal-cost load balancing route filtering.
Refer to the exhibit. Which IPv6 OSPF network type is applied to interface Fa0/0 of R2 by default? broadcast Ethernet multipoint point-to-point.
In OSPF, which LSA type is responsible for pointing to the ASBR router? type 1 type 2 type 3 type 4.
|
