Before parts are put into solution heat treatments. make sure the furnaces and salt baths ________ at the specified heat treating temperature. Be Is Are.
Before the material to be solution heat treated is inserted, the temperature of the system _______ by the temperature measuring instrumentation as being uniform and towithin ‡ 5 ° C (‡ 9 ° F) of the required temperature.
Must be indicated Can be indícated Might be indicated.
________ CERAMIC FIBER DUST. THIS DUST CONTAINS CERAMIC FIBERS THAT MAY CAUSE CANCER. Not to breathe Not breathe Do not breathe.
Guidelines for sensor temperature range usage ________ in ASTM MNL 12, ASTM E230, ASTM E608, ASTM E1137, ASTM E1751, IEC60751, or other internationally recognized standard and the sensor supplier. Can be find Can be founded Can be found.
What does eddy current measure? Volume Electrical conductivy The heat .
Remove the lube fitting (55) ________ (75). the support fitting (60, 65, 70,75) Of From To.
Cuts, nicks, splits or tears in the seal section _______ a result of lack of care in handling and installation. Primarilly Are primarilly Is primarilly .
Equipment shall be provided to clean material in accordance with 3.3.1.1. Where toxic or harmful cleaners are employed, they shall be used in compliance with the applicable health and safety regulations. The word "applicable" in the previous reading is closest in meaning to: Suitable Different Useless .
WARNING - The Export Control or Intellectual Property language on this page takes precedence over any such language that ______ on subsequent pages of this document. May appear Should appear Must appear.
Periodic calibration of electrical conductivity testing equipment and instrument conductivity standards shall be performed _______ the requirements of MIL-STD-1537 Both are correct In according with In accordance with.
Quench delay time in air furnaces when the door to open and ends when the last corner of the load is immersed in the quenchant. Quench delay time starts in salt baths when the first corner of the load or part emerges from the salt and ends when the last corner of the load or part is immersed in the quenchant. Start/Starts Started/Start Starts/Starts.
AFTER THE BUSHINGS ARE FLARED, _______ FLUSH WITH THE FAYING SURFACES. They must be They May be They should be.
Do not remove components from the aft entry door assembly that are riveted or bonded _____ replacement is necesary.
Unless However Nevertheless.
The temperature of the quenchant ______ more than 20 F (11 C) from quenching one heat treatment load. The maximum quenchant temperature at the startof quench must be 90 F (32c) Must not increase Should not increase Might not increase.
This specification the requirements for heat treatment of aluminum alloys. Annealing, solution treatment, precipitation treatment and stress relief requirements are included. Establish Establishes Stablishs.
Before heat treatment, clean the parts to remove forming lubricants, marking fluids, or other unwanted material that can cause blistering, surface attack, or staining _______ subsequent processing. Remove anodized coating before heat treatment. From During While .
Choose the correct word order: Sensor Calibration Results Calibration Sensor Results Sensor Results Calibration.
Forgings that ______ be in a stress relieved temper such as -TXX51, -TXX52, or - TXX54can be quenched in cold water. Going to Will Is.
CAUTION: ______ ENGINE FUEL OR OIL FALL ON THE ENGINE. UNWANTED FUEL OR OIL MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FUEL OR OIL CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS. Do not let Not let Not to let.
The hardness test equipment when in use shall be checked against test blocks at leas! once per day to ensure accurate and repeatable results. The conductivity test equipment shall require a periodic standardization every hour of continuous operation. Equipment which _____ accurate or repeatable results shall be corrected and recalibrated Does not provide Do not provide Is not provide.
Use _____ cold water rinse to remove glycol films after quenching. Agitate theparts in a cold water immersion rinse for a minimum of 10 minutes. The agitateds A agitated An agitated.
The Emergency evacuation alert svstem _____ either from the cockpit or the purser station. Activating May be activated Active.
Test Cycle-This standard specifies the Rockwell test cycle _____ recommenclations or requirements for five separate parts of the cycle. By state By states By stating .
Select if the following statement is true or false: Removal and installation of the splices and fasteners are necessary to install the handle box assembly and the torque tube assembly. True False.
Do ______ inspection of the component interface and or the adjacent area. A An Many .
_______ the manufacturer instructions and _____ the correct protective clothing when you _____ liquid nitrogen. Liquid nitrogen is dangerous. Wear-Use-Apply Read-Apply-Use Obey-Wear-Use.
The protection build-up is not the same in all areas of the aircraft structure. Some components are manufactured from corrosion-resistant material and require no surface protection. The phrase build up is closed to the meaning: A gradual accumulation or increase A gradual reduction or decrease.
Shoulder straps can be separately released by _____ the auxiliary control located on top of the buckle.
Select one: Pressing Press To Press.
Remove escape rope housing covers
for captain and first officer sides in
order ______ access to escape ropes. To gain Gaining Gain.
Remove adhesive with emery cloth,grade 80 to 100. Remaining Are remained Is remained.
PUT THE ASSEMBLY WITH THE
CURVATURE OF THE WINDOW
PANES AND THE MOUNTING HOLES Showed As Shown As show.
Examine the history or defect card, if
there is one, to find defective areas which you must look at. _______
and examine the components (See
TASK 57-43-22-100-801-A01 and TASK 57-43-22-210-801-A01 to find the condition and or the cause of the problem, if there is one. You must clean You must for clean You must to clean.
Composite structures _____ a surface treatment them against the effects of lighting strike, ultra violet rays and erosion. Had - to be protected Has - to protect Have - to protect.
WHY DO WE HAVE TO USE ONLY SPECIFIED CLEANING MATERIALS AND SOLUTIONS OR THEIR EQUIVALENTS? BECAUSE THE SURFACE
PROTECTOR COULD BE DAMAGED IF UNSPECIFIED MATERIALS ARE USED. IT IS IMPORTANT THAT THE MANUFACTURER'S MIXING, APPLICATION AND TREATMENT INSTRUCTIONS ARE FOLLOWED. BECAUSE WE HAVE TO BE CAREFUL IN NOT MIXING
DIFFERENT CHEMICALS THAT MAY CAUSE DAMAGE TO OUR PHYSICAL INTEGRITY.
|
