GENFAM 777

Which of the following information is showed by the part list?. What the size and the shape the parts are. Where, and how many times a part is used. Tolerances.

- If we need to identify how parts and assemblies fit together, which of the following areas, do we have to use?. Picture sheet. Part list. Drawing detail.

“The list of items for installation drawings is almost identical to the list of items for assembly drawings”. True. False.

Which is the diameter of the following fastener: 3/16. 3/8. 5/32.

What types of drawings shows the profiles of a variety of formed sheet metal parts with bend descriptions and dimensioned holes, no fasteners are called out?. Detail drawings. ASSY drawings. Installing drawings.

A part number consist of the following. Dash number. Drawing number + Dash number. Drawing number.

Are numerical values expressed in units of measure, usually inches and decimals. True. False.

Are used to show the length, height, and width of objects: linear dimensions. picture sheets. parts list.

“Removable fastener, are not shown using fastener symbol codes” Regarding the above statement,. True. False. IDK.

What make up the Boeing Production Drawing systems?. Picture sheets, Parts list, Engineering standards. Picture sheets, Parts list, Drawings. Detail drawing , Assembly drawing, Engineering standards.

Which of the following information is showed by the picture sheet?. What the parts look like, What size and shape. How the parts and assemblies fit together, where are located. All above correct.

“Drawing shows what to do and the engineering standards tell how it must be done”, regarding the above statement,. true. false.

Production or engineering drawings may be divided into three types. They are: Detail drawings, Assembly and Installation drawings. Detail drawings, Picture sheets and Installation drawings. Detail drawings, Assembly and Number drawings.

Which drawing gives all the information for fabricating single parts?. Detail drawings. Assembly drawings. Installation drawings.

Which is the current numbering system used for production drawing?. Line number. MSN (Manufacture Serial Number). Number drawings.

A drawing in which the subassemblies or parts are shown as brought together on the aircraft is called. Detail drawings. Assembly drawings. Installation drawings.

Line number is the consecutive production number of the airplane that is built.” regarding the above statement,. true. false.

The title block is always located in the: upper right corner. lower right corner. lower left corner.

Which of the following is a basic effectivity?. 763. PL501. P3990.

The measurements showing the ideal or 'perfect' sizes of parts on drawings are called. tolerances. dimensions. allowances.

What type of line is normally used in a Drawing to represent the edges of a object?. Medium weight dashed lines. Alternate Short and long light dashes. Medium Solid Line.

The Revision block on the picture sheet is always located in the: lower left corner. upper right corner. lower right corner.

When reading a blueprint, a dimension is given as 4.388 inches +.003 -.003. Which statement is true?. The minimum aceptable size is 4.383 inches. The maximun aceptable size is 4.391 inches. The minimum aceptable size is 4.382 inches.

Which statement is true regarding an orthographic projection?. There are always six views. It could have as many as eight views. In practice, only two or three views are needed to fully describe a part.

In the reading of aircraft blueprints, the term 'tolerance,' used in association with aircraft parts orcomponents,. none of the above. are numerical values expressed in units of measures. is the difference between the maximun and minimun dimension limits.

When reading a blueprint, a dimension is given as 4.387 inches +0.005 - 0.002 which statement is true?. The maximun aceptable size is 4.390 inches. The minimum aceptable size is 4.382 inches. The minimum aceptable size is 4.385 inches.

Zone numbers on aircraft blueprints are used to: indicate different sections of the aircraft. to locate parts, sections, and views on large drawings. locate parts in the aircraft.

"Removable fastener, are not shown using fastener symb regarding the above statement,. true. false.

Isometric drawing shows of a part in the same. two sides. three sides. four sides.

What type of line is normally used in a blueprint to re to the viewer?. Medium Solid Line. Alternate Short and long light dashes. Medium weight dashed lines.

Side Talking about part numbers for opposite part, which dash number will be asigned. Odd number. Even number.