Which counter indicates the total number of frames that a switch port failed to transmit? Frame Packet outputs Collisions Output errors.
Refer To the exhibit a network has been planned as shown. Which three statements accurately describe the areas and devices in the network plan ? network device A is a switch network device B is a switch network device A is a hub network device B is a hub Area 1 contains a layer 2 device Area 2 contains a layer 2 device.
Which two differences between the OSI and TCP/IP networking models are true? (choose two) The OSI model places the TCP protocols in the application layer Only the tcp/ip model has a session layer Only the tcp/ip model has six layers Only the OSI model has seven layers Only the TCP/IP model has a network interface layer.
Which two things does router do when it forwards a packet? (choose two) Determine the next hop on the path Switches the packet to the appropriate outgoing interfaces Updates the destination IP address Computes the destination host address Forwards ARP request.
Which two attributes of a packet charge it every router along the path from source to destination? Destination MAC address Source MAC address Packet MTU Destination IP address Source IP address.
How does a Layer 2 switch differ from a hub? A switch always induces latency into the frame transfer time A switch operates at a lower, more efficient layer of the OSI model A switch does not decrease the number of collision domains A switch tracks MAC addresses of directly-connected devices.
Which feature is only supported by named access lists? Contiguous ports Destination-address filtering Tcp flag filtering Logging.
Which ntp concept indicates the distance between a device and the reliable time source? Clock offset Reference Stratum Dispersion.
Which value or values does RIP use to determine the routing table metric for a route? Hop count Bandwidth and delay Bandwidth Bandwidth and hop count.
Drag and drop the vlan port membership modes from the left onto the correct descriptions on the right Private VLAN Dynamic-access Trunk Static-access Tunnel.
Drag and drop the logging configuration commands from the left onto the logging locations they configure on the right. Logging host Logging buffered Logging console Terminal monitor.
Drag and drop the steps in the frame-rewrite process from the left into the correct sequence in the right the frame encapsulates the packet the frame is created the packet is forwarded to the next hop the router recalculates the ipv4 header checksum the router receives the packet.
Which type of ipv6 address does the slaac process create? Multicast address Global address Anycast address Link-local address.
Which statement about the inside interface configuration in a NAT deployment is true? It is defined globally It identifies the location of source addresses for outgoing packets to be traslated using access or router maps it must configured it static NAT is used It identified the public ip address that traffic will use to reach the internet.
Drag and drop the statements about static routing or dynamic routing from the left into the static or dynamic categories on the right. It can load-balance traffic over multiple paths even through more than one device It provides minimal route security unless additional configuration is applied It requires manual intervention when a link fails It can support multiple routes to the same destination It can support only one route to an individual destination The distance command is not supported.
Drag and drop the tcp/ip protocols from the left onto the correct transmission protocols on the right Telnet SMTP HTTP DNS SNMP RTP.
Refer to the exhibit. You ping a remote device by name from a router, and the ping opeartion returns this response. What are two reason for this problem? (CHOOSE TWO) the DNS server databases does not include a record for the name the router is blacklisted by the DNS server Only one DNS server is configured on the router A firewall blocket the ping An ACL on the router blocket the ping.
If a router receives a route 192.168.1.0/24 from peers running OSPF and EIGRP, how does the router forward traffic destine to that network? (una) It always uses the path learned from EIGRP because EIGRP has lower administrative distance it load- balances traffic across both paths it used the path with the lowest metric It always uses the path learned from OSPF because OSPF is a vendor-natural protocol.
What is the default number of secure MAC addresses for an interface configured with port security? 1 255 1042 3072.
Which command can you enter to add VLAN 800 to an existing without affecting other VLANs? Switchport trunk pruning vlan add 800 Switchport trunk native vlan 800 Switchport trunk allowed vlan 800 Switchport trunk allowed vlan add 800.
You recently applied a common configuration to several PC on different VLANs the pc are connected to same switch with a route-on-a-stick but users report that the PCs cannot ping one another. Which two are possible reasons for the problem? (Choose two) The ip default network command is misconfigured on the router The trunking protocol is configured incorrectly on the router sub interfaces The VLAN is configured incorrectly on the router subinterfaces The native vlan on the router is misconfigured The access ports on the pcs are misconfigured .
Which two commands must you apply to a router to configure it as router on a stick? (Choose two) Vtp transparent Vtp domain Spanning tree portfast Encapsulation Ip address.
You have configured two hosts that are connected to a single switch but reside in different VLANS. Which statement about the configuration is true? The two hosts can communicate with icmp The two hosts are unable o communicate without trunk port The two hosts are unable to communicate without a router The two hosts are unable to communicate without a hub.
Drag ad drop the steps in the process of reloading a router without loading its running configuration from the left into the correct sequence on the right. Not all steps are used. Enter the boot command Enter the break command Enter the confreg 0x2102 command Enter the confreg 0x2142 command Enter the reset command to reboot the router and ignore the saved configuration Power-cycle the router.
Complete this task requires this use of various show commands from the CLI of router 1 to answer 4 multiple-choice questions. This does not require any configuration.
Note: the show running-configuration and the show startup-configuration have been disabled in this simulation.
Access the multiple-choice question, click on the numbered boxes on the right of the panel.
There are 4 multiple-choice question with this task. Be sure to answer all question before leaving this item.
Literal A: what is the subnet broadcast address of the LAN connected to Router 1? 192.168.117.15 192.168.117.31 192.168.117.63 192.168.117.127 255.255.255.255.
Complete this task requires this use of various show commands from the CLI of router 1 to answer 4 multiple-choice questions. This does not require any configuration.
Note: the show running-configuration and the show startup-configuration have been disabled in this simulation.
Access the multiple-choice question, click on the numbered boxes on the right of the panel.
There are 4 multiple-choice question with this task. Be sure to answer all question before leaving this item.
Literal B: What is the bandwidth on the WAN interface of Router1? 16 Kbit/sec 32 Kbit/sec 64 Kbit/sec 128 Kbit/sec 512 Kbit/sec 1544 Kbit/sec.
Complete this task requires this use of various show commands from the CLI of router 1 to answer 4 multiple-choice questions. This does not require any configuration.
Note: the show running-configuration and the show startup-configuration have been disabled in this simulation.
Access the multiple-choice question, click on the numbered boxes on the right of the panel.
There are 4 multiple-choice question with this task. Be sure to answer all question before leaving this item.
Literal C: Including the address on the Router 1 FastEthernet interface, how many host can have IP addresses on the LAN to which Router 1 is connected? 6 30 62 126.
The hosts in the LAN are not abe to connect to the ISP. Which commands resolve this issue? () Router 1 (conf)# interface fa0/0
Router 1 (conf-if)# no shutdown () Router 1 (conf)# interface fa0/1
Router 1 (conf-if)# no shutdown () Router 1 (conf)# interface s0/0
Router 1 (conf-if)# no shutdown () Router 1 (conf)# interface s0/1
Router 1 (conf-if)# no shutdown () Router 1 (conf)# interface s0/0
Router 1 (conf-if)# ip address 10.11.12.13 255.255.255.252 () Router 1 (conf)# interface s0/1
Router 1 (conf-if)# ip address 10.11.12.13 255.255.255.252
.
Which three statements accurately describe cdp? (CHOOSE THREE) Cdp is an IEEE standard protocol Cdp is a network layer protocol Cdp is a cisco proprietary protocol Cdp can discover cisco devices thar are not directly connected Cdp can discover directly connected neighboring cisco devices Cdp is datalink layer protocol.
Which prefix length is most appropriate to support an ipv6 point to point link without ipv6 address space? /32 /64 /127 /128.
|
