Which VxRail model is a 4 node, 2U chassis? P Series G Series V Series S Series.
Match each VxRail model to its intended us G Series E Series V Series P Series S Series.
What is the only VxRail model that can be used in a 2 node Cluster? P Series E Series S Series V Series.
Match each VxRail data protection solution to its description. Data Protection Suite for VMware vSphere Replication Active/Active Stretched Clusters Data Domain Virtual Edition RecoverPoint for VMs.
What is a characteristic of a 2 node VxRail Cluster? Supported on VxRail V4.7.100 or higher Supported on G Series only Nodes can be added Must be attached to a switch.
What is the maximum number of nodes supported by VxRail version 4.7.100? 32 64 96 128.
What is a basic switch requirement when deploying a network switch to support VxRail? IPv6 Multicast is required on all vSAN ports IPv4 Multicast is required on all vSAN ports IPv4 Unicast is not required on any VxRail ports IPv6 Multicast is required on all VxRail ports.
What is a feature of vSphere Distributed Switches (vDS)? Provide core elements for vSphere Network I/O Control (NIOC) Maintain network runtime state for VMs as they move across Clusters Present a centralized interface for vSAN configuration Enable out of band monitoring of network traffic.
The Dell EMC OMNI Plug-in utilizes which network, and for what purpose? Private Management Network on VLAN 4096; for SFS communications Private Management Network on VLAN 0; for internal management purposes Management Network; for ssh access Management Network; for vSphere communications.
What is a characteristic of RecoverPoint for VMs? Recommended for use on VxRail Clusters with a minimum of 4 nodes Takes any point in time copy on a per node basis Software only, hypervisor-based replication solution Each VxRail node includes 15 licenses for RecoverPoint for VMs.
How much are backup speeds increased with Data Domain Virtual Edition DD Boost? 25% 50% 75% 100%.
What is the minimum bandwidth requirement between the data sites in a VxRail vSAN Stretched Cluster? 100 Mbps 10 Gbps 25 Gbps 1 Gbps.
Which storage policy setting enables remote protection in a vSAN Stretched Cluster? PFTT = 2 PFTT = 1 SFTT = 2 SFTT = 1.
Which component does the VxRail Appliance use to capture events and provide real-time holistic notifications about the state of applications, VMs, and hardware? iDRAC VMware vRealize Operations VMware vRealize Log Insight Dell EMC OMNI vCenter plug-in.
An administrator needs to manage their VMs. However, vCenter Server is currently unavailable. Which user interface can the administrator use as an alternative? iDRAC vSphere Web Client vSphere Client VMware Host Client.
What is used to automate VxRail tasks? vSphere Client VxRail REST API VxRail Manager Plug-in VxRail Manager UI.
Starting with which version of VxRail is the VxRail Plug-in installed automatically? v4.5.2xx v4.5.3xx v4.7.0xx v4.7.1xx.
VxRail 4.7.1xx has been deployed with embedded vCenter. What is the name of the vCenter datacenter for the newly deployed VxRail Cluster? 'Marvin-Datacenter' 'VxRail-Datacenter' Datacenter name used during deployment 'VxRail-Virtual-SAN-Cluster'.
You are planning to install Data Domain Virtual Edition in your VxRail 4.7.1xx environment. Where should you navigate to in the vSphere Client to download the required software? Home > VxRail Dashboard > Download VxRail Cluster > Configure > VxRail > Market Home > VxRail > Support > Download VxRail Cluster > Configure > System > Update.
A VxRail administrator has been informed by Dell EMC that an Internet software upgrade is available for their VxRail Cluster. The VxRail administrator logs into the vSphere Client and goes to the VxRail System Update page. The page only shows the Local Upgrade option.
What is a possible reason that the Internet Upgrade option is unavailable? VxRail administrator has insufficient privileges Workstation accessing vSphere Client does not have Internet connectivity Secure Remote Services has not been enabled VxRail Manager VM does not have Internet connectivity.
A VxRail administrator wants to search for VxRail related knowledge base articles through the VxRail Dashboard. Which action must the administrator perform to use this feature? Configure Internet access proxy settings for the VxRail Manager VM Register for a VxRail Community login and enter the credentials in the vSphere Client Work with Dell EMC to register the VxRail Appliance in the Install Database Configure the Dell EMC Support Account in the vSphere Client.
What are all the actions that can be performed from the Disk Information panel of the Physical View of a VxRail E Series disk? Add Disks
Shut down
Toggle Chassis LED Toggle Disk LED
Replace Disk Replace Disk
Add Disks Toggle Disk LED
Add Disks.
How is the VMware HCIA Management role associated with a user in vCenter after the VxRail system has been deployed? Add user to HCIA Management group User is automatically added to the role when created Assign the role directly to the user at the object level Add user to the Administrators group.
What is a Dell EMC best practice when adding storage to an existing VxRail Cluster? Add cache disks before storage disks and follow the procedures documented in the VxRail Administration Guide Add disks to the first node and follow the appropriate SolVe procedures Add disks in a balanced manner across all nodes and follow the appropriate SolVe procedures Add storage disks before cache disks and follow the procedures documented in the VxRail Administration Guide.
Where would you run the Add Disk procedure on the VxRail Cluster? VxRail Physical View VxRail Cluster View VxRail Management View VxRail Storage View.
What is a consideration when planning for node expansion of an existing 4 node All-Flash Dell EMC VxRail 4.7.1xx Cluster? New nodes can be hybrid or All-Flash Expansion procedure must be performed by Dell EMC or a Dell EMC partner New nodes must be identical to the existing nodes vSphere Client is used to perform the expansion procedure.
A VxRail administrator needs to add storage capacity to a 4 node VxRail V Series Cluster. Each node currently has one cache and five capacity disks.
What does the administrator need, per node, to fully populate the available disk slots? 3 cache and 15 capacity disks 1 cache and 5 capacity disks 1 cache and 6 capacity disks 2 cache and 10 capacity disks.
As a VxRail administrator, where in vSphere would you go to generate a VxRail log bundle? Hosts and Clusters > Configure > VxRail > Troubleshooting Hosts and Clusters > Monitor > VxRail > Support Hosts and Clusters > Monitor > VxRail > Health Monitoring Hosts and Clusters > Configure > VxRail > System.
An administrator is upgrading a VxRail with an Internal vCenter from version 4.5.xxx to 4.7.1xx. What is needed for the upgrade process? Allocate additional network ports Reserve additional storage space for data conversion Update BIOS on the nodes before upgrade Provide temporary IP address to the vCenter Server.
What is a symptom of a potential network issue on a VxRail partitioned Cluster? Two or more of the Cluster nodes cannot communicate over all VxRail networks One node of the Cluster cannot communicate over all VxRail networks VMs with access to storage are powered off VMs without access to storage are powered on.
A VxRail administrator has to replace a failed capacity disk on a VxRail 4.7.1xx node. Dell EMC has shipped the replacement disk.
What is the recommended method to perform the disk replacement? Use SolVe to generate the disk replacement procedure
Follow the steps detailed in the procedure Log into the VxRail Manager UI
Go to Physical View of the Node
Select the faulty disk and click Replace Disk Log into the vSphere Client
Go to Physical View of the VxRail Node
Select the faulty disk and click Replace Disk Refer to the VxRail Appliance Administration Guide
Follow the steps detailed in the guide.
A VxRail Cluster has just been deployed. The VxRail administrator wants to ensure that virtual machines can be deployed successfully and that the vSAN Cluster is operational.
What can be done to test this quickly with minimal effort? Set up HCIBench and run a test Run the vSAN VM Creation Test Run the vSAN Health Check Run the vSAN Network Performance Test.
A system administrator cannot enable deduplication on a 4 node S570 Cluster. What might be the reason? Performance Service is not enabled. vSAN data-at-rest encryption is not enabled. Deduplication is not supported on this model. Compression is not enabled.
Which file types would benefit most from vSAN deduplication and compression? Bitmap and video files Text and encrypted files Program and graphics files Text and program files.
In a VxRail Appliance, what does vSAN use in the form of flexible data containers to store and manage data? Datastores Disk Groups Objects Virtual Volumes.
As an administorator, you are asked to view the health on the vSAN on the VxRail Cluster. You select the VxRail Cluster in the Navigation panel in vCenter.
Under which tab could you run the vSAN health check? Configure Datastores Monitor Summary.
What are the requirements for vSAN Data-at-Rest-Encryption in a VxRail environment? All-Flash VxRail with an internal Key Management Server All-Flash or hybrid VxRail with internal vCenter Server All-Flash or hybrid VxRail with an external Key Management Server All-Flash VxRail with an external vCenter Server.
As a VxRail administrator, you discover that one of the nodes in your Cluster has a hardware issue. Dell EMC support will be arriving to replace the node. You have a vCenter Standard license on this vCenter. You need to place the faulty node into maintenance mode.
Which vSAN data migration option should you use when placing the node into maintenance mode? Ensure accessibility No data migration Full data migration Default option.
What is the maximum number of capacity devices that can be contained in a vSAN disk group? 4 5 6 7.
At what level is vSAN Encryption enabled? Cluster VM Host Disk group.
A new VM will be deployed on an All-Flash VxRail vSAN Cluster. The administrator plans to use a vSAN storage policy with FTT = 2 and FTM = Erasure Coding.
What is the recommended number of VxRail nodes required to support the policy and allow self- 4 5 6 7.
What is defined by the Object space reservation in a VxRail vSAN Storage Policy? Net failures that each storage object can tolerate Logical size of the VMDK provisioned during deployment Stripe size of each storage object Percentage of the VMDK size provisioned during deployment.
When using a vSAN storage policy with FTT = 2 and FTM = Mirroring, how many witness components exist for a VMDK? 0 1 2 3.
What are the vSAN storage policy settings applied to the VxRail Manager VM during initial setup of an All-Flash VxRail Cluster? Number of failures to tolerate = 1
Object space reservation (%) = 100 Number of failures to tolerate = 1
Failure tolerance method = Erasure coding
Object space reservation (%) = 100 Number of failures to tolerate = 1
Failure tolerance method = Mirroring
Object space reservation (%) = 50 Number of failures to tolerate = 2
Failure tolerance method = Mirroring.
A clone image is being used to deploy a VM. What is a consideration? VM configuration can drift over time Low level of repeatability 100% customizable Updating templates is a manual process.
Match each VMware management task with its description. Building a VM Cloning a VM Importing a VM Deploying a VM.
What features are supported by the Dell EMC OMNI Plug-in? vSS and VLAN Trunking Private VLANs and VLAN Trunking vSS and vDS vDS and VLAN Trunking.
What is NOT a valid API Method? PUT DELETE POST REMOVE.
Which VxRail API request for log collection supports the POST method? /request/<Request ID> /support/logs/<Log ID> /support/logs /support/logs/<Log ID>/download.
VxRail system administrator has been tasked to collect support logs for vCenter, VxRail Manager, and ESXi for 10 VxRail nodes. They are receiving the following response in the API body:
{
"message": "Insufficient storage capacity."
}
What can be done to resolve this issue?
Reduce the number of nodes Set autoclean to false Set autoclean to true Reduce the log types.
|
