Test 2. piloto comercial helicóptero

TEST BORRADO, QUIZÁS LE INTERESE: 2. Piloto Comercial Helicóptero - Aircraft Systems

COMENTARIOS	ESTADÍSTICAS	RÉCORDS

REALIZAR TEST

Título del Test:
2. Piloto Comercial Helicóptero - Aircraft Systems

Descripción:
DGAC Peru

Autor:
Yesid Cadavid
OTROS TESTS DEL AUTOR

Fecha de Creación:
18/10/2020

Categoría: Otros

Número Preguntas: 102

COMPARTE EL TEST

COMENTAR

No hay ningún comentario sobre este test.

Temario:

Before shutdown, while at idle, the ignition key is momentarily turned OFF. The engine continues to run with no interruption; this is normal because the engine is usually stopped by moving the mixture to idle cut-off. should not normally happen. Indicates a magneto not grounding in OFF position. is an undesirable practice, but indicates nothing is wrong.
During a near-vertical power approach into a confined area with the airspeed near zero, what hazardous condition may develop? Ground resonance. Settling with power. Blade stall vibration.
Which procedure will result in recovery from settling with power? Increase collective pitch and power. Maintain constant collective pitch and increase throttle Increase forward speed and partially lower colective pitch.
The addition of power in a settling with power situation produces an increase in airspeed. even greater rate of descent. increase in cyclic control effectiveness.
Under which situation is accidental settling with power likely to occur? A steep approach in which the airspeed is permitted to drop to nearly zero. A shallow approach in which airspeed is permitted to drop below 10 MPH Hovering in ground effect during calm wind, high density altitude conditions.
Which is true with respect to recovering from an accidental settling with power situation? Antitorque pedals should not be utilized during the recovery. Recovery can be accomplished by increasing rotor RPM, reducing forward airspeed, and minimizing maneuvering. Since the inboard portions of the main rotor blades are stalled, cyclic control effectiveness will be reduced during the initial portion of the recovery.
When operating at high forward speed, retreating blade stall is more likely to occur under conditions of low gross weight, high density altitude, and smooth air. high gross weight, low density altitude, and smooth air. high gross weight, high density altitude, and turbulent air.
What are the major indications of an incipient retreating blade stall situation, in order of occurrence? Low-frecuency vibration, pitchup of the nose, and a roll in the direction of the retreating blade Slow pitchup of the nose, high-frecuency vibration, and a tendency for the helicopter to roll. Slow pitchup of the nose, tendency for the helicopter to roll, followed by a medium-frecuency vibration.
How should a pilot react at the onset of retreating blade stall? Reduce collective pitch, rotor RPM, and forward airspeed Reduce collective pitch, increase rotor RPM, and reduce forward airspeed Increase collective pitch, reduce rotor RPM, and reduce forward airspeed.
The most power will be required to hover over which surface? High grass. Concrete ramp. Rough/uneven ground.
Which flight technique is recommended for use during hot weather? During takeoff, accelerate quickly into forward flight. During takeoff, accelerate slowly into forward flight. Use minimum allowable RPM and maximum allowable manifold pressure during all phases of flight.
To taxi on the surface in a safe and efficient manner, helicopter pilots should use the cyclic pitch to control starting, taxi speed, and stopping. collective pitch to control starting, taxi speed, and stopping antitorque pedals to correct drift during crosswind conditions.
During surface taxiing, the cyclic pitch stick is used to control heading. ground track. forward movement.
To taxi on the surface in a safe and efficient manner, one should use the cyclic pitch to start and stop aircraft movement. maintain heading during crosswind conditions. correct for drift during crosswind conditions.
A pilot is hovering during calm wind conditions. The greatest amount of engine power will be required when ground effect exists. making a left-pedal turn. making a right-pedal turn.
Which statement is true about an autorotative descent? Generally, only the cyclic control is used to make turns The pilot should use the collective pitch control to control the rate of descent The rotor RPM will tend to decrease if a right turn is made with a heavily loaded helicopter.
Using right pedal to assist a right turn during an autorotative descent will probably result in what actions? A decrease in rotor RPM, pitch up of the nose, decrease in sink rate, and increase in indicated airspeed. An increase in rotor RPM, pitch up of the nose, decrease in sink rate, and increase in indicated airspeed. An increase in rotor RPM, pitch down of the nose, increase in sink rate, and decrease in indicated airspeed.
Using left pedal to assist a left turn during an autorotative descent will probably cause the rotor RPM to increase and the airspeed to decrease. decrease and the aircraft nose to pitch down. increase and the aircraft nose to pitch down.
When planning slope operations, only slopes of 5° gradient or less should be considered, primarily because ground effect is lost on slopes of steeper gradient. downwash turbulence is more severe on slopes of steeper gradient most helicopter are not designed for operations on slopes of steeper gradients.
When making a slope landing, the cyclic pitch control should be used to lower the downslope skid to the ground. hold the upslope skid against the slope. place the rotor disc parallel to the slope.
Takeoff from a slope is normally accomplished by making a downslope running takeoff if the surface is smooth simultaneously applying collective pitch and downslope cyclic control bringing the helicopter to a level attitude before completely leaving the ground.
What is the procedure for a slope landing? Use maximum RPM and maximum manifold pressure If the slope is 10° or less, the landing should be made perpendicular to the slope. When parallel to the slope, slowly lower the upslope skid to the ground prior to lowering the downslope skid.
You are hovering during calm wind conditions and decide to make a rightpedal turn. In most helicopters equipped with reciprocating engines, the engine RPM will tend to increase. decrease. remain unaffected.
During calm wind conditions, in most helicopters, which of these flight operations would require the most power? A left-pedal turn. A right-pedal turn. Hovering in ground effect.
Leaving the carburetor heat on while taking off leans the mixture for more power on takeoff. will decrease the takeoff distance. will increase the ground roll.
A way to detect a broken magneto primary grounding lead is to idle the engine and momentarily turn the ignition off. add full power, while holding the brakes, and momentarily turn off the ignition. run on one magneto, lean the mixture, and look for a rise in manifold pressure.
Fouling of spark plugs is more apt to occcur if the aircraft: Gains altitude with no mixture adjustment descends from altitude with no mixture adjustment throttle is advance very abruptly.
The most probable reason an engine continues to run after the ignition switch has been turned off is: carbon deposits glowing on the spark plugs a magneto ground wire is in contact with the engine casing a broken magneto ground wire.
If the ground wire between the magneto and the ignition switch becomes disconnected, the engine will not operate on one magneto cannot be started with the switch in the BOTH position. could accidentally start if the propeller is moved with fuel in the cylinder.
The pilot controls the air/fuel ratio with the throttle manifold pressure mixture control.
Detonation may occur at high-power settings when the fuel mixture ignites instantaneously instead of burning progressively and evenly. an excessively rich fuel mixture causes an explosive gain in power the fuel mixture is ignited too early by hot carbon deposits in the cylinder.
For gyroplanes with constant-speed propellers, the first indication of carburetor icing is usually A decrease in engine RPM A decrease in manifold pressure Engine roughness followed by a decrease in engine RPM.
Detonation can be caused by A rich mixture low engine temperatures using a lower grade of fuel than recommended.
The uncontrolled firing of the fuel/air charge in advance of normal spark ignition is known as instantaneous combustion detonation. pre-ignition.
Fuel/air ratio is the ratio betweeen the: Volume of fuel and volume of air entering the cylinder Weight of fuel and weight of air entering the cylinder Weight of fuel and weight of air entering the carburetor.
Which statement is true concerning the effect of the application of carburetor heat? It enriches the fuel/air mixture. It leans the fuel/air mixture It has no effect on the fuel/air mixture.
Detonation occurs in a reciprocating aircraft engine when: there is an explosive increase of fuel caused by too rich a fuel/air mixture the spark plugs receive an electrical jolt caused by a short in the wiring the unburned fuel/air charge in the cylinders is subjected to instantaneous combustion.
If complete power failure should occur while cruising at altitude, the pilot should partially lower the collective pitch, close the throttle, then completely lower the collective pitch lower the collective pitch as necessary to maintain proper rotor RPM, and apply right pedal to correct for yaw close the throttle, lower the collective pitch to the full-down position, apply left pedal to correct yaw, and establish a normal power-off glide.
When making an autorotation to touchdown, what action is most appropriate? A slightly nose-high attitude at touchdown is the proper procedure. The skids should be in a longitudinally level attitude at touchdown. Aft cyclic application after touchdown is desirable to help decrease ground run.
During the entry into a quick sstop, how should the collective pitch control be used? It should be lowered as necessary to prevent ballooning raised as necessary to prevent a rotor overspeed raised as necessary to prevent a loss of altitude.
During a normal approach to a hover, the collective pitch control is used primarily to maintain RPM control the rate of closure control the angle of descent.
During a normal approach to a hover, the cyclic pitch is used primarily to maintain heading. control rate of closure control angle of descent.
Normal RPM should be maintained during a running landing primarily to ensure adequate directional control until the helicopter stops that sufficient lift is available should an emergency develop. longitudinal and lateral control, especially if the helicopter is heavily loaded or high density altitude conditions exist.
Which is true concerning a running takeoff? If a helicopter cannot be lifted vertically, a running takeoff should be made One advantage of a running takeoff is that the additional airspeed can be converted quickly to altitudfe A running takeoff may be possible when gross weight or density altitude prevents a sustained hover at normal hovering altitude.
When conducting a confined area-type operation, the primary purpose of the high reconnaissance is to determine the type of approach to be made. suitability of the area for landing height of the obstructions surrounding the area.
During a pinnacle approach under conditions of high wind and turbulence, the pilot should make a shallow approach, maintaining a constant line of descent with cyclic applications. normal approach, maintaining a slower-than-normal rate of descent with cyclic applications steeper-than-normal approach maintaining the desired angle of descent with collective applications.
What type approach should be made to a pinacle under conditions of relatively high wind and turbulence? A normal approach A steeper-than-normal approach A shallower-than-normal approach.
If turbulence and downdrafts are expected during a pinnacle approach to a rooftop heliport, plan to make a steeper-than-normal approach normal approach, maintaining a lower-than-normal airspeed shallow approach, maintaining a higher-than-normal airspeed.
If ground resonance is experienced during rotor spin-up, what action should you take? Taxi to a smoooth area Make normal takeoff immediately Close the throttle and slowly raise the spin-up lever.
The principal factor limiting the never-exceed speed (Vne) of a gyroplane is turbulence and altitude blade-tip speed, which must remain below the speed of sound. lack of sufficient cyclic stick control to compensate for dissymmetry of lift or retreating blade stall, depending on which occurs first.
Why should gyroplane operations within the cross-hatched portion of a Height vs. Velocity chart be avoided? The rotor RPM may build excessively high if it is necessary to flare at such low altitudes. Sufficient airspeed may not be available to ensure a safe landing in case of an engine failure. Turbulence near the surface can dephase the blade dampers causing geometric unbalanced conditions on the rotor system.
The principal reason the shaded area of a Height vs. Velocity chart should be avoided is rotor RPM may decay before ground contact is made if an engine failure should occur rotor RPM may build excessively high if it is necessary to flare at such low altitudes. insufficient airspeed would be available to ensure a safe landing in case of an engine failure.
During the transition from pre-rotation to flight, rotor blades change pith Simultaneously to the same angle of incidence Simultaneously but to different angles of incidence To the same degree at the same point in the cycle or rotation.
With respect to vortex circulation, which is true? Helicopters generate downwash turbulence, not vortex circulation The vortex strength is greatest when the generating aircraft is flying fast Vortex circulation generated by helicopters in forward flight trail behind in a manner similar to wingtip vortices generated by airplanes.
Which is true with respect to vortex circulation? Helicopters generate downwash turbulence only, not vortex circulation The vortex strength is greatest when the generating aircraft is heavy, clean, and slow When vortex circulation sinks into ground effect, it tends to dissipate rapidly and offer little danger.
Coning is caused by the combined forces of drag, weight, and translational lift. lift and centrifugal force. flapping and centrifugal force.
The forward speed of a rotorcraft is restricted primarily by dissymmetry of lift transverse flow effect. high-frecuency vibrations.
When hovering, a helicopter tends to move in the direction of tail rotor thrust. This statement is true; the movement is called transverse tendency true; the movement is called translating tendency false; the movement is opposite the direction of tail rotor thrust, and is called translating tendency.
The purpose of lead-lag (drag) hinges in a three-bladed, fully articulated helicopter rotor system is to compensate for Coriolis effect. dissymmetry of lift. blade flapping tendency.
What happens to the helicopter as it experiences translating tendency? It tends to dip slightly to the right as the helicopter approaches approximately 15 knots in takeoff It gains increased rotor efficiency as air over the rotor system reaches approximately 15 knots It moves in the direction of the tail rotor thrust.
The unequal lift across the rotor disc that occurs in horizontal flight as a result of the difference in velocity of the air over the advancing half of the disc area is known as coning. disc loading dissymmetry of lift.
The lift differential that exists between the advancing blade and the retreating blade is known as Coriolis effect translational lift dissymmetry of lift.
Most helicopters, by design tend to drift to the right when hovering in a nowind condition. This statement is false;helicopters have no tendency to drift, but will rotate in that direction true; the mast or cyclic pitch system of most helicopters is rigged forward, this with gyroscopic precession will overcome the tendency true; the mast or cyclic pitch system of most helicopters is rigged to the left to overcome this tendency.
When a rotorcraft transitions from straight-and-level flight into a 30° bank while maintaining a constant altitude, the lift force must increase and the load factor will increase increase and the load factor will decrease. remain constant and the load factor will decrease.
Cyclic control pressure is applied during flight that results in a maximum increase in main rotor blade pitch angle at the "three o'clock" position. Which way will the rotor disc tilt? Aft. Left Right.
Cyclic control pressure is applied during flight that results in a maximum decrease in pitch angle of the rotor blades at the "12 o'clock" position. Which way will the rotor disc tilt? Aft. Left. Right.
The primary purpose of the tail rotor system is to assist in making coordinated turns maintain heading during forward flight counteract the torque effect of the main rotor.
Can the tail rotor produce thrust to the left? No; the right thrust can only be reduced, causing tail movement to the left. Yes; primarily so that hovering turns can be accomplished to the right. Yes; primarily to counteract the drag of the transmission during autorotation.
The main rotor blades of a fully-articulated rotor system can flap and feather collectively. flap, drag, and feather independently feather independently, but cannot flap or drag.
A reciprocating engine in a helicopter is more likely to stop due to in-flight carburetor icing than will the same type engine in an airplane. This statement has no basis in fact. The same type engine will run equally well in either aircraft. is true. The freewheeling unit will not allow windmilling (flywheel) effect to be exerted on a helicopter engine is false. The clutch will immediately release the load from the helicopter engine under engine malfunctioning conditions.
What is the primary purpose of the clutch? It allows the engine to be started without driving the main rotor system It provides disengagement of the engine from the rotor system for autorotation. It transmits engine power to the main rotor, tail rotor, generator/alternator, and other accesories.
What is the primary purpose of the freewheeling unit? It allows the engine to be started without driving the main rotor system It provides speed reduction between the engine, main rotor system, and tail rotor system It provides disengagement of the engine from the rotor system for autorotation purposes.
The main rotor blades of a semirigid rotor system can flap together as a unit flap, drag, and feather independently. feather independently, but cannot flap or drag.
Rotorcraft climb performance is most adversely affected by higher than standard temperature and low relative humidity lower than standard temperature and high relative humidity higher than standard temperature and high relative humidity.
The most unfavorable combination of conditions for rotorcraft performance is low density altitude, low gross weight, and calm wind high density altitude, high gross weight, and calm wind high density altitude, high gross weight, and strong wind.
How does high density altitude affect rotorcraft performance? Engine and rotor efficiency is reduced Engine and rotor efficiency is increased It increases rotor drag, which requires more power for normal flight.
A medium-frecuency vibration that suddenly occurs during flight could be indicative of a defective main rotor system tail rotor system. transmission system.
In most helicopters, medium-frecuency vibrations indicate a defective engine main rotor system tail rotor system.
Abnormal helicopter vibrations in the low-frecuency range are associated with which system or component Tail rotor. Main rotor Transmission.
Helicopter low-frecuency vibrations are always associated with the main rotor. tail rotor. transmission.
A high-frecuency vibration that suddenly occurs during flight could be an indication of a defective transmission freewheeling unit main rotor system.
Ground resonance is less likely to occur with helicopters that are not equipped with rigid rotor systems fully articulated rotor systems semi-rigid rotor systems.
The proper action to initiate a quick stop is to apply forward cyclic, while raising the collective and applying right antitorque pedal. aft cyclic, while raising the collective and applying left antitorque pedal aft cyclic, while lowering the collective and applying right antitorque pedal.
The best power mixture is that fuel/air ratio at which cylinder heat temperatures are the coolest the most power can be obtained for any given throttle setting a given power can be obtained with the highest manifold pressure or throttle setting.
Detonation can be caused by too lean a mixture low engine temperatures using higher grade fuel than recommended.
Applying carburetor heat will not affect the mixture lean the fuel/air mixture enrich the fuel/air mixture.
An abnormally high engine oil temperature indication may be caused by a defective bearing the oil level being too low operating with an excessively rich mixture.
What will occur if no leaning is made with the mixture control as the flight altitude increase? The volume of air entering the carburetor decreases and the amount of fuel decreases The density of air entering the carburetor decreases and the amount of fuel increases. The density of air entering the carburetor decreases and the amount of fuel remains constant.
Unless adjusted, the fuel/air mixture becomes richer with an increase in altitude because the amount of fuel decreases while the volume of air decreases remains constant while the volume of air decreases remains constant while the density of air decreases.
The basic purpose of adjusting the fuel/air mixture control at altitude is to decrease the fuel flow to compensate for decreased air density decrease the amount of fuel in the mixture to compensate for increased air density. increase the amount of fuel in the mixture to compensate for the decrease in pressure and density of the air.
Frecuent inspections should be made of aircraft exhaust manifold-type heating systems to minimize the possibility of exhaust gases leaking into the cockpit a power loss due to back pressure in the exhaust system a cold-running engine due to the heat withdrawn by the heater.
During the flare portion of a power-off landing, the rotor RPM tends to remain constant increase initially decrease initially.
Which would produce the slowest rotor RPM? A vertical descent with power A vertical descent without power Pushing over after a steep climb.
If the RPM is low and the manifold pressure is high, what initial corrective action should be taken? Increase the throttle Lower the collective pitch Raise the collective pitch.
During climbing flight, the manifold pressure is low and the RPM is high. What initial corrective action should be taken? Increase the throttle Decrease the throttle Raise the collective pitch.
During level flight, if the manifold pressure is high and the RPM is low, what initial corrective action should be made? Decrease the throttle Increase the throttle Lower the collective pitch.
When operating a helicopter in conditions favorable for carburetor icing, the carburetor heat should be adjusted to keep the carburetor air temperature gauge indicating in the green arc at all times OFF for takeoffs, adjusted to keep the carburetor air temperature gauge indicating in the green arc at all other times OFF during takeoffs, approaches, and landings; adjusted to keep the carburetor air temperature gauge indicating in the green arc at all other times.
As altitude increases, the Vne of a helicopter will increase. decrease remain the same.
The anti-torque system fails during cruising flight and a powered approach landing is commenced. If the helicopter yaws to the right just prior to touchdown, what could the pilot do to help swing the nose to the left? Increase the throttle Decrease the throttle Increase collective pitch.
If anti-torque failure occurred during cruising flight, what could be done to help straighten out a left yaw prior to touchdown? A normal running landing should be made. Make a running landing using partial power and left cyclic Apply variable throttle to help swing the nose to the right just prior to touchdown.
Should a helicopter pilot ever be concerned about ground resonance during takeoff? No; ground resonance occurs only during an autorrotative touchdown Yes; although it is more likely to occur on landing, it can occur during takeoff Yes, but only during slope takeoffs.
An excessively steep approach angle and abnormally slow closure rate should be avoided during an approach to a hover, primarily because the airspeed indicator would be unreliable a go-around would be very difficult to accomplish settling with power could develop, particularly during the termination.

Denunciar Test

▲