2V0-41.20 NXT

01 An NSX administrator noticed that the nsxcli command times out after 600 secs of idle time. Which CLI command disables the nsxcli time out value on NSX Manager?. set cli-timeout 0. set cli-timeout enabled. set cli-timeout disabled. set cli-timeout 1.

02 Which two commands are used to query the arp-table of a logical switch? (Choose two.). get logical-switch arp-table <logical-switch-uuid>. get logical-switch arp-table <vni>. get logical—switch arp-table. get logical-switch <logical-switch-uuid> arp-table. get logical-switch <vni> arp-table.

03 Which two statements describe the characteristics of an Edge Cluster in NSX-T 3.0 Data Center? (Choose two.). can have a maximum of 8 edge nodes. must have only active-active edge nodes. can have a maximum of 10 edge nodes. can contain multiple types of edge nodes (VM or bare metal). Must contain only one type of edge nodes (VM or bare metal).

04 A customer is preparing to deploy VMware Kubernetes on an NSX-T Data Center. What is the minimum MTU size for the UPLINK profile?. 1500. 1650. 1550. 1600.

05 Which CLI command is used to start the NSX Manager virtual machine in the KVM environment?. virsh start <NSX-Manager-ID>. virsh poweron <nsx-manager-ID>. virsh start <NSX-Manager-Name>. virsh poweron <nsx-manager-name>.

06 Which CLI command is used to disable SSH timeout on NSX Manager and NSX Edge nodes?. set cli ssh timeout 0. set cli-timeout 0. set esxcli ssh session off. nsxcli ssh session on.

07 Which command is used to set the NSX Manager's logging-level to debug mode for troubleshooting?. set service nsx-manager logging-level debug. set service nsx-manager log-level debug. set service manager log-level debug. set service manager logging-level debug.

08 What are the advantages of using a Tier-O Gateway in ECMP mode? (Choose two.). stateful services leveraged. Failover of services. traffic predictability. traffic load balancing. increased north/south bandwidth.

09 Which discovery protocol is supported for hypervisor transport nodes?. Adobe Real-time CDP. Cisco Discovery Protocol. Link Layer Discovery Protocol. Neighbor Discovery Protocol.

10 An NSX administrator is creating a Tier-1 Gateway configured in Active-Standby High Availability Mode. In the event of node failure, the failover policy should not allow the original failed node to become the Active node upon recovery. Non-Preemptive. Preemptive. Enable Preemptive. Disable Preemptive.

11 Which three services are compatible with VRF Lite? (Choose three.). VPN. Intrusion Detection. NAT. Load Balancer. DHCP.

12 An NSX administrator is configuring the KVM hypervisor host as a transport node and wants to apply the Failover Order as a NIC teaming policy. Which profile allows the administrator to configure the NIC Teaming policy as Failover Order?. N-VDS/VDS Profile. Transport Node Profile. Host Switch Profile. Uplink Profile.

13 An NSX administrator has been tasked with deploying a NSX Edge Virtual machine through an ISO image. Which virtual network interface card (vNIC) type must be selected while creating the NSX Edge VM to allow participation in overlay and VLAN transport zones?. e1000. VMXNET2. VMXNET3. Flexible.

14 When a stateful service is enabled for the first time on a Tier-O Gateway, what happens on the NSX Edge node?. SR and DR doesn't need to be connected to provide any stateful services. DR is instantiated and automatically connected with SR. SR is instantiated and automatically connected with DR. SR and DR is instantiated but requires manual connection.

15 A DevOps user has deployed a Kubernetes Pod in vSphere. What does the term ClusterIP represent within NSX-T?. Deployment of T1 with NLB service. Deployment of Distributed Router. Deployment of Distributed Load Balancing service. Deployment of TO and T1.

16 An NSX administrator has configured a load balancer virtual server on a Tier-1 Gateway. In order to advertise the load balancer virtual IP to the Tier-0 Gateway, which route advertisement configuration has to be done on the Tier-1 Gateway? (Choose two.). Advertise All LB SNAT IP Routes. All Static Routes. Information. Advertise All LB VIP Routes. Advertise All NAT Routes.

17 Which two logical router components span across all transport nodes? (Choose two.). DISTRIBUTED_ROUTER_TIER0. SERVICE_ROUTER_TIER0. TIER0_DISTRIBUTED_ROUTER. DISTRIBUTED_ROUTER_TIER1. SERVICE_ROUTER_TIER1.

18 Which three teaming policy modes are supported by NSX-T Data Center? (Choose three.). Destination MAC. Load Balanced Source IP. Failover Order. Destination Port. Load Balanced Source MAC. Load Balanced Source.

19 A company is deploying a NSX-T Data Center micro-segmentation in their vVSphere environment to secure a simple application composed of web, app, and database tiers. The naming convention will be: - WKS-WEB-SRV-XXX - WKY-APP-SRR-XXX - WKI-DB-SRR-XXX. Create an Ethernet based security policy. Group all by means of tags membership. Use Edge as a firewall between tiers. Do a service insertion to accomplish the task.

20 Which two steps must an NSX administrator take to integrate VMware Identity Manager in NSX-T to support role-based access control? (Choose two.). Create a SAML authentication in VMware Identity Manager using the NSX Manager FQON. Add NSX Manager as a Service Provider (SP) in VMware Identity Manager. Create an OAuth 2.0 client in VMware Identity Manager. Enter the Identity Provider (IdP) metadata URL in NSX Manager. Enter the service URL, Client Secret, and SSL thumbprint in NSX Manager.

21 Which choice is correct when deploying a NSX Edge in a KVM only environment?. deploy NSX Edge VM with OVF template. deploy NSX Edge on a bare-metal server. deploy NSX Edge VM with QCOW2 image. deploy NSX Edge on physical switch.

22 Which three functions require a Services Router (SR) component on an Edge node? (Choose three.). Service Insertion. Distributed Routing. Packet Forwarding. Gateway Firewall. Distributed Firewall. Virtual Private Network.

23 Which two BGP configuration parameters can be configured in the VRF Lite gateways? (Choose two.). Route Aggregation. Route Distribution. Graceful Restart. BGP Neighbors. Local AS.

24 Which three can an administrator define in a transport node profile? (Choose three.). Logical Router. Segment Profile. Segment. Uplink Profile. VDS switch configuration. N-VDS switch configuration.

25 Which three different transport nodes could be configured in the data plane? (Choose three.). VM or Bare Metal NSX Edge. vShield Edge VM. Bare Metal server. ESXi and Hyper-V. NSX Edge VM on KVM. ESXi and KVM.

26 Which CLI command does an NSX administrator run on the NSX Manager to generate support bundle logs if the NSX UI is inaccessible. get support-bundle file vcpnv.tgqz. set support-bundle file vcpnv.tqz. vm-support. esxcli system syslog config logger set --id=nsxmanager.

27 Which two statements are true for a Tier-1 Gateway? (Choose two.). supports ECMP. owned and configured by the Tenant. always configured in active-standby mode. owned and configured by Service Provider. connects to physical networks.

28 What are two valid options when configuring the scope of a distributed firewall rule? (Choose two.). Segment Port. Group. Segment. DFW. Tier-1 Gateway.

29 What are two supported N-VDS modes? (Choose two.). DPDK Datapath. Overlay Datapath. Secure Datapath. Enhanced Datapath. Standard Datapath.

30 What are three NSX Manager roles? (Choose three.). cloud. manager. zookeeper. policy. master. controller.

31 Which two ports are used by a transport node to communicate with the management and control planes in NSX-T Data Center 3.0? (Choose two.). 5685. 1235. 5671. 5678. 1234.

32 Which NSX CLI command is used to check the GENEVE tunnel status on ESXi transport node?. get host-switch <Host-Switch-Name> tunnels. get transport-node tunnel status. get host-switch <Host-Switch-Name> tunnel status. get transport-node tunnel state.

33 Which TraceFlow traffic type should an NSX administrator use for validating connectivity between App and DB virtual machines that reside on different segments?. Multicast. Anycast. Unicast. Broadcast.

34 Where are Distributed Firewall logs containing access decisions stored?. NSX API. NSX Edge. NSX Manager. Hypervisor transport node.

35 Which two commands does an NSX administrator use to check the IP address of the VMkernel port for the GENEVE protocol on the ESXi transport node? (Choose two.). esxcfg-nics -1. net-dvs. esxcli network nic list. esxcfg-vmknic -1. esxcli network ip interface ipv4 get.

36 Which two tools are used for centralized logging in NSX-T Data Center? (Choose two.). vRealize Log Insight. Syslog Server. vRealize Network Insight. vRealize Operations. vRealize Automation.

37 Where do you configure the VLANs used in VRF Lite? (Choose two.). uplink interface of the default Tier-O gateway. uplink trunk segment. downlink interface of the default Tier-O gateway. uplink interface of the VRF gateway. segment connected to the Tier-1 gateway.

38 An NSX administrator wants to create a Tier-O Gateway to support equal cost multi-path (ECMP) routing. Which failover detection protocol must be used to meet this requirement?. Beacon Probing (BP). Host Standby Router Protocol (HSRP). Bidirectional Forwarding Detection (BFD). Virtual Router Redundancy Protocol (VRRP).

39 How is the RouterLink port created between a Tier-1 Gateway and Tier-O Gateway?. Automatically created when Tier-1 is created. Manually create a Segment and connect to both Tier-1 and Tier-O Gateways. Manually create a Logical Switch and connect to bother Tier-1 and Tier-O Gateways. Automatically created when Tier-1 is connected with Tier-O from NSX UI.

40 Which three protocols could an NSX administrator use to transfer log messages to a remote log server? (Choose three.). SSL. HTTPS. TLS. UDP. SSH. TCP.

41 Which CLI command on NSX Manager and NSX Edge is used to change NTP settings?. get time-server. get timezone. set ntp-server. set timezone.

42 Which command is used to display the network configuration of the Tunnel Endpoint (TEP) IP on a bare metal transport node?. ifconfig. tcpdump. debug. ipconfig.

43 Which component does the hyperbus interface (vmk50) provide network connectivity to?. containers running on ESXI/KVM transport nodes. virtual machines and containers running across transport nodes. virtual machines running on the same hypervisor. virtual machines running in the same segment.

44 An NSX administrator would like to export syslog events that capture messages related to NSX host preparation events. Which message ID (msgid) should be used in the syslog export configuration command as a filter?. SYSTEM. FABRIC. GROUPING. MONITORING.

45 What is the most restrictive NSX-T built-in role which will allow a user to apply configuration changes on a NSX Edge?. Cloud Service Administrator. Network Engineer. Network Operator. NSX Administratds.

46 Which command is used to change the NSX CLI administrator password?. set user administrator password <old-password> <new-password>. set user admin password <old-password> <new-password>. set user admin password <password> old-password <old-password>. set user administrator password <password> old-password <old-password>.

47 In a NSX-T Data Center environment, an administrator is observing low throughput and congestion between the Tier-0 Gateway and the upstream physical routers.Which two actions could address low throughput and congestion? (Choose two.). Deploy Large size Edge node/s. Configure ECMP on the Tier-0 gateway. Configure NAT on the Tier-0 gateway. Add an additional vNIC to the NSX Edge node. Configure a Tier-1 gateway and connect it directly to the physical routers,.

48 An NSX administrator is planning to deploy a multi-tier routing topology in their NSX-T Data Center environment to provide north-south connectivity for the VMs. Which routing component must be deployed?. Tier-1 Gateway. Edge Services Gateway. Tier-0 Gateway. Layer 2 Gateway.

49 Which two choices are solutions of the NSX portfolio? (Choose two.). vRealize Automation. NSX Distributed IDS/IPS. vRealize Network Insight. Tanzu Kubemetes Grid. NSX Service Mesh.

50 Which statement is true regarding the audit user account? (Choose two.). The admin user must set the password for the audit account to log in to NSX Manager. The administrator must run the set user audit password <password> command. The audit user must be created and have its password changed to log into the NSX Manager. The administrator must run the set audit user password <password> command. The audit user has read-write access to the NSX Manager.

51 When deploying east-west network introspection, which Service Virtual Machine (SVM) deployment method achieves the least amount of traffic hairpinning?. Create a secondary vNIC on each quest VM for SVM communication. Place a partner SVM on each compute cluster node. Centralize partner SVMs in a service cluster. Add partner SVMs to an edge cluster.

52 Which NAT type must the NSX-T Data Center administrator create on the Tier-O or Tier-1 Gateway to allow Web VM to initiate communication with public networks?. SNAT. Reverse NAT. DNAT. 1:1 NAT.

53 How is the intra-tier transit link connection created between SR and DR for a Tier-0 Gateway?. Manually create a gateway interface and mark it as transit. Automatically created when SR is initialized,. Automatically created when DR is created,. Manually create external uplink interface and mark it as transit.

54 Which log is used to see a failed NSX-T installation of a VIB package on ESXi transport nodes?. /var/log/vmware/eam/eam.log. /var/log/esxupdate.log. var/log/syslog.log. War/log/hostd.log.

55 An NSX administrator has configured a KVM hypervisor as a transport node. Which kernel module on KVM implements a N-VDS?. openvswitch. etherswitch. sx-vswitch. vswitch.

56 An NSX administrator would like to configure syslog for a KVM transport node. Which host log files could be exported to a remote syslog server?. /var/log/cloudnet/nsx-ccp.log. /var/log/vmware/nsx-syslog. /var/log/cfgAgent. log. /var/log/nsx-audit-_log.

57 Which step must be performed before deploying an additional NSX Manager from the NSX-T UI?. Prepare the ESXi hosts as Transport Nodes. Configure the Virtual IP of the cluster. Register vCenter Server as a Compute Manager. Create an Edge Cluster.

58 Which two choices are use cases for Distributed Intrusion Detection? (Choose two.). Identify security vulnerabilities in the workloads. Use agentless antivirus with Guest Introspection. Quarantine workloads based on vulnerabilities. Identify risk and reputation of accessed websites. Gain insight about micro-segmentation traffic flows.

59 Which statement describes the VMware Virtual Cloud Network Vision?. Virtual Cloud Network connects and protects virtual machines running in KVM environments. Virtual Cloud Network connects and protects virtual machines running in vSphere environments. Virtual Cloud Network connects and protects applications, regardless of their physical locations. Virtual Cloud Network connects and protects applications and data, regardless of their physical locations.

60 Which network virtualization technologies can be used with an Ethernet VPN (EVPN) deployment in NSX-T Data Center? (Choose two.). Virtual Extensible Local Area Network (VXLAN). Multiprotocol Border Gateway Protocol (MP-BGP). Open Shortest Path First (OSPF). Multiprotocol Label Switching (MPLS). Virtual Routing and Forwarding (VRF).

61 Which profile must be attached to the ESXi cluster to prepare the host for NSX-T Data Center?. Transport Node Profile. Uplink Profile. Switching Profile. Host Profile.

62 Which tool could be used to inspect the path of a packet in the data plane?. Port Connection. Port Mirroring Session. Netflow. Traceflow.

63 A customer has a network where BGP has been enabled and the BGP neighbor is configured on the Tier-O Gateway. A NSX-T Data Center administrator used the logical-routers command to retrieve this information: Which two commands must be executed to check BGP neighbor status? (Choose two.). vrf3. vrf1. vrf4. sa-nsxedge-01(tier1_sr)> get bgp neighbor. sa-nsxedge-01(tier0_sr)> get bgp neighbor. sa-nsxedge-01(tier0_dr)> get bgp neighbor.

64 When running nsxcli on an ESXi host, which command will show the Replication mode?. get logical-switch <Local-Switch-UUID> status. get logical-switch <Logical-Switch-UUID>. get logical-switches. get logical-switch status.

65 Which statement is true about an alarm in a Suppressed state?. An alarm can be suppressed for a specific duration in days. An alarm can be suppressed for a specific duration in minutes. An alarm can be suppressed for a specific duration in seconds. An alarm can be suppressed for a specific duration in hours.

66 Which two statements are true about the implementation of multicast in NSX-T Data Center? (Choose two.). Multicast routing is implemented with PIM Sparse-Mode. IGMP Snooping is used to populate multicast forwarding tables. Tier-0 gateways can be the Rendezvous Point. Multicast is supported in ESXi and KVM transport nodes. An Edge can be the Rendezvous Point.

67 What are three characteristics of a transport zone? (Choose three.). defines the scope and reachability of a Segment. defines the potential reach of transport nodes. configured with multiple N-VDS\VDS. optional for creating a segment. configured with a Single N-VDS/VDS.

68 Which CLI command should be executed on a KVM hypervisor to retrieve the VM interface UUID?. virsh dumpxml <VM Name> | grep interfaceid. virsh get-interface <VM Name>. virsh show <VM Name> | grep interfaceid. virsh list-interface <VM Name>.

69 A security administrator needs to configure a firewall rule based on the domain name of a specific application. Profile. Source. Service. Policy.

70 An NSX administrator is creating a NAT rule on a Tier-0 Gateway configured in active-standby high availability mode. Which two NAT rule types are supported for this configuration? (Choose two.). 1:1. NAT. Destination NAT. Port NAT. Reflexive NAT. Source NAT.

71 Which tool injects packets and provides various observation points along the packet's path between two NSX-T managed objects?. IPFIX. Port Mirroring. Traceflow. SPAN mirrors.

72 Which three steps must be carried out to configure North-South / East-West Network Inspection? (Choose three.). Service Deployment. Service Insertion. Service Consumption. Service Registration. Service Introspection.

73 The NSX Control Plane is responsible for which two functions? (Choose two). receive and validate configuration from NSX Policy. host API services. propagate topology information. push stateless configurations to forwarding engines. maintain packet-level statistics.

74 Which three steps are required to create an IPsec VPN tunnel? (Choose three.). Create an IPsec service. Add a local endpoint. Configure an IPsec session. Configure a distributed firewall policy. Add a logical switch.

75 Which network tool could an administrator use on an ESXi 7 host to capture packets when troubleshooting connectivity issues?. Wireshark. pktcap-uw. tcpdump. net-stats.

76 An administrator has a requirement to have consistent policy configuration and enforcement across NSX-T instances. What feature of NSX-T Data Center fulfills this requirement?. Multi-hypervisor support. Policy-driven configuration. Load balancer. Federation.

77 How does Traceflow tool identify issues in a network?. Compares intended network state in the control plane with Tunnel End Point (TEP) keepalives in the data plane. Compares the management plane configuration states containing control plane traffic and error reporting from transport node agents. Injects synthetic traffic into the data plane and observes the results in the control plane. Injects ICMP traffic into the data plane and observes the results in the control plane.

78 An NSX administrator is using ping to check connectivity between VM1 running on ESXi1 to VM2 running on ESXi2. The ping tests fails. The administrator knows the maximum transmission unit size on the physical switch is 1600. Which command does the administrator use to check the VMware kernel ports for tunnel end point communication?. esxcli network diag ping -H <destination IP address>. vmkping ++netstack=geneve -d -s 1572 <destination IP address>. vmkping ++netstack=vxlan-d -s 1572 <destination IP address>. esxcli network diag ping -I vmkO -H <destination IP address>.

79 How many IPs are required when deploying a highly available NSX Management Cluster with VIP in a production environment?. 5. 6. 3. 4.

80 An NSX administrator has deployed an NSX Edge on a bare-metal server. Which command registers the NSX Edge with the NSX Manager?. join management-cluster <nsx-cluster-IP> username admin password <admin-password> thumbprint <nsx-manager-thumbprint>. join cluster <nsx-cluster-IP> username root password <root-password> thumbprint <nsx-manager—thumbprint>. join policy-manager <nsx-manager-ip> username root password <root-password> thumbprint <nsx-manager-thumbprint>. join management-plane <nsx-manager-ip> username admin password <admin-password> thumbprint <nsx-manager-thumbprint>.

81 Which CLI command shows syslog on NSX Manager?. show log manager follow. get log-file auth.log. get log-file syslog. /var/log/syslog/syslog.log.

82 Which Network and Security virtualization solution provides network hybridity and mobility?. NSX Intelligence. VMware HCX. VMware Tanzu Service Mesh. NSX Advanced Load Balancer.

83 An NSX administrator has observed connectivity issues between the NSX Manager and the KVM Transport Node. Which two log files could be used to troubleshoot the issue on the KVM Transport Node? (Choose two.). /usr/vmware/nsx-syslog. /var/log/vmware/nsx-syslog. /usr/vmware/log/syslog. /var/log/syslog. /var/log/nsx/syslog.

84 An NSX administrator is troubleshooting a connectivity issue with virtual machines running on an ESXi transport node. Which feature in the NSX UI shows the mapping between the virtual NIC and the host's physical adapter?. Switch Visualization. Port Mirroring. Activity Monitoring. IPFIX.

85 What needs to be configured on a Tier-O Gateway to make NSX Edge Services available to a VM on a VLAN-backed logical switch?. Service interface. Loopback Router Port. Downlink interface. VLAN Uplink.

86 Which CLI command would an administrator use to allow syslog on an ESXi transport node when using the esxcli utility?. esxcli network firewall ruleset set -a -e false. esxcli network firewall ruleset -e syslog. esxcli network firewall ruleset set -r syslog -e false. esxcli network firewall ruleset set -r syslog -e true.

87 Which two choices are prerequisites to configure NSX-T on VDS? (Choose two.). MTU 1500. MTU 1400. vSphere Distributed Switch 6.5. vSphere Distributed Switch 7.0. MTU 1600.

88 Which tool could be used to configure BGP on a Tier-O Gateway?. PowerShell. ESX CLI. API. NSX CLI.

89 An NSX Administrator has created a segment named WEB-LS from the NSX UI and noticed the segment is not realized on the KVM Transport node. What are two possible causes for this issue? (Choose two.). The KVM Transport node has hardware issues and will not realize the WEB-LS Segment. Since the Compute Manager is disconnected in NSX UI, the WEB-LS segment will not be realized on the KVM Transport Node. The virtual machines running on the KVM Transport Node are connected to the WEB-LS segment, but are in Powered Off state. The virtual machines running on the KVM Transport Node are not connected to the VDS. The virtual machines running on the KVM Transport Node are not connected to the WEB-LS Segment.

90 What are two types of supported IPSec VPNs in NSX-T Data Center? (Choose two.). policy-based IPSec VPN. Layer-7 based IPSec VPN. route-based IPSec VPN. Open source based IPSec VPN. SSL based IPSec VPN.

91 An NSX administrator is reviewing syslog and notices that Distributed Firewall Rules hit counts are not being logged. What could cause this issue?. Syslog is not configured on the ESXi transport node. Distributed Firewall Rule logging is not enabled. Syslog is not configured on the NSX Manager. Zero Trust Security is not enabled.

92 A user is assigned these two roles in NSX Manager: - LB Admin - Network Engineer What privileges does this user have in the system?. read permissions on all networking services and full access permissions on load balancing features. full access permissions on all networking services and full access permissions on load balancing features. full access permissions on all networking services and read permissions on load balancing features. read permissions on all networking services and read permissions on load balancing features.