AACA - PT 2

Which of the following is a primary security feature supported by Aruba switches?. Built-in intrusion prevention system. Web content filtering. Role-based access control. All are correct.

What does a wireless client do first when its countdown timer reaches zero and it receives a Transmit Opportunity (TXOP)?. It immediately sends its Data Frames and receives an ACK from the AP. It sends a CTS-to-self announcement to the ESP gateway. It sends a CTS-to-self announcement to the AP and all other clients. It sends a reassociation request frame to the AP and sends its Data Frames.

What is an advantage of using Layer 2 MAC authentication?. it matches user names to MAC address. No setup is required on the client. MAC allow lists are easily maintained over time. MAC identifiers are hard to spoof.

What is indicated by a flashing amber global status indicator LED on an Aruba CX6200M?. The switch has a recoverable fault. Self-test is in progress. The firmware image is corrupt. The switch is booting the firmware image.

Refer to Exhibit. Which server will receive the smallest quantity of data?. 172.17.17.43. 10.100.100.25. 10.99.26.25. 192.168.0.56.

You have been asked to onboard a new Aruba 6300M in a customer deployment You are working remotely rather than on-site You have a colleague installing the switch. The colleague has provided you with a remote console session to configure the edge switch You have been asked to configure a link aggregation going back to the cores using interfaces 1/1/51 and 1/1/52. The Senior Engineer of the project has asked you to configure the switch and 1Q uplink with these guidelines 1. Add VLAN 20 to the local VLAN database with name Mgmt 2. Add L3 SVl on VLAN 20 for Management using address 10 in the 10.1.10/24 subnet 3. Add LAG 1 using LACP mode active for the uplink 4. use vlan 20 as the native vlan on the LAG 5. Make sure the interfaces are all ON. Which configuration script will achieve the task?. Edge1# conf t vlan 20 name Mgmt interface vlan 20 ip address 10.1.1.10/24 no shut interface lag 1 shut vlan access 20 lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut. Edgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1.1 10/24 no shut interface 1/1/51.1/1/52 shut vlan trunk native 20 vlan trunk allowed all lag 1 lacp mode active interface 1/1/51.1/1/52 no shut. Edgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1 1 10/24 no shut interface lag 1 shut vlan trunk native 20 vlan trunk allowed all lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut interface 1/1/51.1/1/52 no shut. conf t vlan 20 name Mgmt ip address 10 1 1.10/24 no shut interface lag 1 shut vlan trunk native 1 vlan trunk allowed all lacp mode active int 1/1/51.1/1/52 shut no routing interface lag 1 no shut Interface 1/1/51.1/1/52 no shut.

Which statement about manual switch provisioning with Aruba Central is correct?. Manual provisioning does not require DHCP and requires DNS. Manual provisioning does not require DHCP and does not require DNS. Manual provisioning requires DHCP and does not require DNS. Manual provisioning requires DHCP and requires DNS.

You need to ensure that voice traffic sent through an ArubaOS-CX switch arrives with minimal latency. What is the best scheduling technology to use for this task?. QoS shaping. Rate limiting. Strict queuing. DWRR queuing.

Match the feature to the Aruba OS version (Matches may be used more than once.). Aruba 8. Aruba 10.

Describe the purpose of the administrative distance. Routes teamed via external BGP have a higher administrative distance than routes learned via OSPF. The administrative distance is used as a trust rating tor route entries. The administrative distance for a static route is 10. The higher administrative distance is preferred.

Describe the functionality of ARP. Clients do not have an ARP cache and always ask for the default gateway. ARP maps MAC addresses to switch ports. ARP maps layer-3 IP addresses to layer-2 MAC addresses. ARP uses multicast to build the ARP table.

Please match the use case to the appropriate authentication technology. Clearpass. Cloud.

An AP signal strength of .0000001 milliwatts equals how many dBm?. -90 dBm. -60 dBm. -70 dBm. -80 dBm.

List the WPA 4-Way Handshake functions in the correct order. Distributes an encrypted GTK to the client. Exchanges messages for generating PTK. Proves knowledge of the PMK. Sets first initialization vector (IV).

You are configuring a network with a stacked pair of 6300M switches used for distribution and layer 3 services. You create a new VLAN for users that will be used on multiple access stacks of CX6200 switches connected downstream of the distribution stack You will be creating multiple VLANs/subnets similar to this will be utilized in multiple access stacks What is the correct way to configure the routable interface for the subnet to be associated with this VLAN?. Create a physically routed interface in the subnet on the 6300M stack for each downstream switch. Create an SVl in the subnet on each downstream switch. Create an SVl in the subnet on the 6300M stack, and assign the management address of each downstream switch stack to a different IP address in the same subnet. Create an SVl in the subnet on the 6300M stack.

Which feature can network administrators use to centralized RF planning and optimization service when using an Aruba mobility master architecture?. Airwave. Client Match. AirMatch. Client Wave.

When would you bond multiple 20MHz wide 802.11 channels?. To decrease the Signal to Noise Ratio (SNR). To increase throughput between the client and AP. To provision highly available AP groups. To utilize high gain omni-directional antenas.

Where are wireless client roaming decisions made?. Client device. Virtual Controller. Joint decision made by the origination and destination APs. Aruba Central.

A hacker has altered a user's 3-Way Handshake in order to gain access to their session. Which security mechanism would intelligently deny this traffic?. Out-of-band management (00BM). Stateless firewall. Access Control List (ACL). Stateful firewall.

What happens when the signal from an AP weakens by being absorbed as it moves through an object?. APs will use bonded channels to decrease latency to clients. Signal to Noise Ratio (SNR) increases. Signal to Noise Ratio (SNR) decreases. Aruba Central dynamically moves clients to neighboring Aps.

Which type of device type and group persona is required to manage a Microbranch environment?. ArubaOS 10 AP Group Persona. ArubaOS 10 Branch Gateway Group Persona. ArubaOS 8 AP Group Persona. ArubaOS 8 Branch Gateway Group Persona.

You need to configure wireless access for several classes of loT devices, some of which operate only with 802 11b. Each class must have a unique PSK and will require a different security policy applied as a role There will be 15-20 different classes of devices and performance should be optimized Which option fulfills these requirements?. Single SSID with MPSK for each loT class using 5 GHz and 6 GHz bands. Single SSID with MPSK for each loT class using 2.4GHz and 5 GHz bands. Individual SSIDs with unique PSK for each loT class, using 5GHz and 6 GHz bands. Individual SSIDs with unique PSK for each loT class, using 2.4GHZ and 5GHz band.

Which part of the WPA Key Hierarchy is used to encrypt and/or decrypt data''. Pairwise Temporal Key (PTK). Pairwise Master Key (PMK). Key Confirmation Key (KCK). number used once (nonce).

What does a slow amber-flashing Stack-LED indicate?. One switch has a stacking failure. A port has a stacking failure Stacking mode Is not selected. Stacking mode selected. Stacking is synchronizing Please wait.

What is the ideal mounting position for a typical Aruba indoor AP?. Horizontal, below a suspended ceiling. Under a office desk. Horizontal, above a suspended ceiling. Vertical, at a wall.

Match the Open Systems Interconnection (OSI) layer with its comparable member of the TCP/IP stack. (Options may be used more than once.). Application. Network interface.

Which commands are used to set a default route to 10.4.5.1 on an Aruba CX switch when lnband management using an SVl is being used?. IP default-gateway 10.4.5.1. ip route 0 0 0.070 10.4 5.1 vrf mgmt. ip route 0.0 0 0/0 10.4.5.1. default-gateway 10.4.5.1.

Match the Open Systems Interconnection (OSI) layer with its function. Application Layer. Presentation Layer. Session Layer. Transport Layer.

Which three channels can be used simultaneously in a 2.4GHz WLAN environment while avoiding any co-channel interference?. 1,6, 11. 1,5, 10. 3,6, 9. 2,7, 11.

When using Aruba Central what can identify recommended steps to resolve network health issues and allows you to share detailed information with support personnel?. Overview Dashboard. OAlOps. Alerts and Events. Audit Trail.

What are the main characteristics of the 6 GHz band?. Less RF signal is absorb by objects in a 6 GHz WLAN. In North America, the 6 GHz band offers more 80 MHz channels than there are 40 MHz channels in the 5 GHz band. The 6 GHz band is fully backward compatible with the existing bands. Low Power Devices are allowed for indoor and outdoor usage.

Which Protocol Data Unit (PDU) represents the data link layer PDU?. PDU1 - Signal. PDU2 - Frame. PDU3 - Packet. PDU4 – Segment.

In which scenarios is Zero Touch Provisioning (ZTP) most beneficial? (Select two). When deploying large scale networks rapidly. In networks where configurations change frequently. For small networks that do not have IT staff. When high security is a concern and manual setup is required.

Which device configuration group types can a user define in Aruba Central during group creation? (Select two.). ESP group. Security group. Ul group. Default group. Template group.

network technician is verifying that a customer successfully connected to the guest network after completing the captive portal. The network technician looks at the access tracker in ClearPass. Which role should be seen when looking at the OUTPUT tab for the customer's session?. Guest authenticated. Captive portal login. Captive portal redirect. Guest logon.

Which statement is true for a device with a MAC address of B8-31-B5-80-41-4F?. The device OUI is B8-31-B5 and the device NIC serial number is 80-41 4F. The device OUI is B8-31 and the device NIC serial number is B5-80-41-4F. The device OUI is 80-41-4F and the device NIC serial number is B8-31-B5. The device OUI is B8-31-B5 and the device serial number is MD5 hash is 80-41-4F.

Based on the given topology, what is the requirement on an Aruba switch to enable LLDP messages to be received by Switch 1 port 1/1/24. When Router 1 is enabled with LLDP?. LLDP is enabled by default. global configuration lldp enable. int 1/1/24, lldp receive. int 1/1/24, no cdp.

When using the network check page in Central, what kind of tests can you run on switches? (Select two.). Speed test (iperf). Ping test. A full hardware check, including a heavy memory check. LED-check.

Which Protocol Data Unit (PDU) represents the network layer PDU?. PDU3 - Packet. PDU4 - Segment. PDU1 - Signal. PDU2 – Frame.

ou are in a meeting with a customer where you are asked to explain the network redundancy feature Multiple Spanning Tree (MSTP). What is the correct statement for this feature?. MSTP configuration ID revision by default as current MSTP root priority. MSTP configuration ID name by default using switch IMC address. MSTP configuration ID name by default using switch serial number. MSTP configuration ID revision by default as switch serial number.

Which are valid steps in troubleshooting Aruba Wireless Access Point connection issues? (Choose three). Check the power settings on the physical switch port connected to the AP. Ensure that the AP is in compliance with the latest firmware updates. Verify network cable integrity from the AP to the switch. Reset the AP to factory default settings.

What is an advantage of using Layer 2 MAC authentication?. MAC allow lists are easily maintained over time. No setup is required on the client. It matches user names to MAC address. MAC identifiers are hard to spoof.

When does the 802.1x authentication process begin when connecting to a secured enterprise mode WLAN?. After the firewall policies are applied to the session. After the client completes 802.11 association. After the captive portal authentication completes. After the WPA 4-Way Handshake is completed.

What capabilities are included in Aruba's ClearPass Policy Manager? (Choose two). Advanced cryptographic module validation. Guest access management with customizable web portals. Device profiling and fingerprinting. Direct cloud management integration.

What are two characteristics of ClientMatch? (Select two.). It optimizes channels of an AP. An algorithm to adjust RF patterns. It is used to locate a client. It is an Aruba patented technology. It helps to move sticky clients to another AP.

How does the Aruba Mobility Controller handle Layer 3 mobility in a campus network?. By maintaining a tunnel to each access point for seamless user transitions. Mobility does not require any special handling at Layer 3. By assigning a unique IP subnet to each wireless client. Through a centralized database that tracks the location and movement of users.

Review the configuration below Why would you configure OSPF to use the IP address 10.1.200.1 as the router ID?. The IP address associated with the loopback interface is non-routable and prevents loops. The loopback interface state is dependent on the management interface state and reduces routing. The IP address associated with the loopback interface is routable and prevents loops. The loopback interface state Is independent of any physical interface and reduces routing updates.

What command is used to add a static route to a network 192.168.10.0/24 via gateway 192.168.1.1 on an Aruba router?. ip route 192.168.10.0 255.255.255.0 192.168.1.1. route add -net 192.168.10.0 netmask 255.255.255.0 gw 192.168.1.1. ip route 192.168.10.0/24 192.168.1.1. add route 192.168.10.0/24 via 192.168.1.1.

What does WPA3-Personal use as the source to generate a different Pairwise Master Key (PMK) each time a station connects to the wireless network?. Session-specific information (MACs and nonces). Opportunistic Wireless Encryption (OWE). Simultaneous Authentication of Equals (SAE). Key Encryption Key (KEK).

What is the function of a Virtual Switching Framework (VSF) in Aruba networking equipment?. It is used to virtualize physical switches into one logical switch. It allows for the stacking of switches to provide redundancy. It enables the creation of a virtual network on the physical switch. It configures virtual LANs across multiple switches.

How does the Aruba Central platform assist in managing Aruba networking devices?. By distributing network traffic evenly across devices. Through centralized cloud-based management and monitoring. By automating the firmware upgrades across all devices. Central does not support device management functions.

How does the Aruba Mobility Controller handle Layer 3 mobility in a campus network?. By assigning a unique IP subnet to each wireless client. Through a centralized database that tracks the location and movement of users. By maintaining a tunnel to each access point for seamless user transitions. Mobility does not require any special handling at Layer 3.

You have physical access to an Aruba CX-Switch with unknown/lost credentials. What are the possible steps to rebuild the credentials? (Select two.). Connect the switch via the console. Then, power cycle the switch. Press and hold the clear button. Then, power-cycle the switch. Press and hold the clear button. Then, press the reset button for 2 seconds and release both buttons. Call Aruba support for a one-time password. Use boot profile 0.

You need to troubleshoot an Aruba CX 6200 4-node VSF stack switch that fails to boot correctly Select the option that allows you to access the switch and see the boot options available for OS images and ServiceOS. Member 2 RJ-45 console port. Member 2 switch mgmt port. Conductor USB-C console port. Conductor mgmt port using SSH.

Match the appropriate QoS concept with its definition. Best Effort. Class of Service. Differentiated services. WMM.

Match the most cost-effective option for cabling each requirement. (All lengths indicate total cable length including patch cable(s), service loops, etc. where used.). Cat 5e cable. Cat 6a cable. Direct Attach Copper (DAC) cable. multimode fiber. single mode fiber.

Refer to the exhibit. In the given topology, a pair of Aruba CX 8325 switches are in a VSX stack using the active gateway. What is the nature and behavior of the Virtual IP for the VSX pair if clients are connected to the access switch using VSX as the default gateway?. Virtual IP is active on the primary VSX switch. Virtual floating IP will failover in case of a failure. Virtual IP is active on both CX switches. Virtual IP uses SVI IP address synced with VSX.

What will perform a hard reset of an Aruba CX switch?. Press the reset button and hold the clear button while releasing the reset button for 5 seconds. Press and hold the reset button for 5 seconds, then release. Press the reset button and the clear button simultaneously. Press the reset button three times.

A client connects to an Aruba AP in tunnel mode and is assigned to a VLAN based on the client's MAC address. Which client VLAN assignment was configured?. Mixed. Static. Native VLAN. Dynamic.

Where can you set the client's broadcast domain when configuring an ArubaOS firewall role?. WLAN Settings. Bandwidth Controls. Access Control Rules. Role-based VLAN override.

Which statement is correct when comparing 5 GHz and 6 GHz channels with identical channel widths?. 5 GHz channels travel the same distances and provide different throughputs to clients compared to 6 GHz channels. 5 GHz channels travel different distances and provide different throughputs to clients compared to 6 GHz channels. 5 GHz channels travel the same distances and provide the same throughputs to clients compared to 6 GHz channels. 5 GHz channels travel different distances and provide the same throughputs to clients compared to 6 GHz channels.

When measuring signal strength, dBm is commonly used and 0 dBm corresponds to 1 mW power. What does -20 dBm correspond to?. -1 mW. .01 mw. 10 mW. 1mW.

You need to troubleshoot an Aruba CX 6300F switch that fails to boot correctly. Select the option that allows you to access the switch and see the boot options available for OS images and ServiceOS. USB-C console port. RJ-45 console port. USB-A console port. Omgmt port using SSH.

You have been asked to troubleshoot failed connectivity between a local subnet in the HQ Office and a remote subnet in the Branch Office. PC1 is unable to ping PC2. Use the provided topology and show command output to identify the reason for the failure: On Branch Office - L3-SW-2- There is no Layer 3 SVI configured in the correct subnet. On HQ Office L3-SW-1 - There is no route to the Branch Office. On HQ Office L3-SW-1 - The switch does not have a static default route to the internet. On Branch Office L3-SW-2- The switch does not have a static route to the HQ Office Local Subnet.

When using the OSPF dynamic routing protocol on an Aruba CX switch, what must match on the neighboring devices to exchange routes?. Hello timers. DR configuration. ECMP method. BDR configuration.

Two independent ArubaOS-CX 6300 switches with Spanning Tree (STP) settings are interconnected with two cables between ports 1/1/1 and 1/1/2 All four ports have "no shutdown" and "no routing" commands. How will STP forward or discard traffic on these ports?. The switch with the lower MAC address will forward on both ports, while the switch with the higher MAC address will forward on both ports. The switch with the lower MAC address will forward on both ports, while the switch with the higher MAC address will discard on one port. The switch with the lower MAC address will discard on one port, while the switch with the higher MAC address will forward on both ports. The switch with the lower MAC address will discard on one port, while the switch with the higher MAC address will discard on one port.

What describes Clearpass OnGuard? (Select two.). Onguard assings an unique identity to each device. It is used for the self-registration of guest devices. OnGuard is an agent, running on client systems. OnGuard is doing posture checks on client systems. It is an intuitive portal for users to securely configure their device.

Which flew in a Layer 3 IPv4 packet header is used to mitigate Layer 3 route loops?. Checksum. Time To Live. Protocol. Destination IP.

How does a single Aruba CX 6300M switch configuration use L3 connectivity to establish routing traffic between switch virtual interfaces 120 and 130?. Routing is enabled by default with Aruba 6300M. Route leaking must be configured in default VRF. Delete 'no routing' from the SVI interfaces. Create static routes between SVI 120 and 130.

When performing live firmware upgrades on Aruba APs. Which technology partitions all the APs based on RF neighborhood data minimizing the impact on clients?. Aruba ClientMatch. Aruba Ai insights. Aruba AirMatch. Aruba ESP.

When using an Aruba standalone AP you select "Native VLAN" for the Client VLAN Assignment. In which subnet will the client IPs reside?. The same subnet as the mobility controller. The same subnet as the Aruba ESP gateway. The same subnet as the mobility conductor. The same subnet as the access point.

A network technician is deploying "headless" devices in the warehouse at the HQ location. So far, an SSID with 802.1X has been configured. However, these new devices lack 802.1X support. Which option would provide enhanced security for these devices?. WPA3-Personal. Multi-Preshared keys (mPSK). WPA2-Enterprise. Opportunistic Wireless Encryption (OWE).

What are two advantages of a UXl? (Select two.). A UXl can be used without any internet connection. A UXl helps to calculate the best WiFi channels in a remote location. A UXl behaves like a client/user. A UXl measures the Wi-Fi coverage of all APs in the given location. A UXl can check different applications, such as HTTP VOIP or Office 365.

What is the correct command to add a static route to a class-c-network 10.2.10.0 via a gateway of 172.16.1.1?. ip-route 10.2.10.0/24 172.16.1.1. ip route 10.2.10.0.255.255.255.0 172.16.1.1 description aruba. ip route 10.2.10.0/24.172.16.11. ip route-static 10.2 10.0.255.255.255.0 172.16.1.1.

Match the Aruba Central technology to the appropriate feature. (Matches may be used more tan once.). AirMatch. ClientMatch.

You need to drop excessive broadcast traffic on ingress to an ArubaOS-CX switch. What is the best technology to use for this task?. Rate limiting. DWRR queuing. QoS shaping. Strict queuing.

What does the status of "ALFOE" mean when checking LACP with "show lacp interfaces'"?. The interface on the local switch is configured as static-LAG. LACP is not configured on the peer side. LACP is in a synchronizing process. LACP is working fine with no problems.

A network administrator with existing IAP-315 access points is interested in Aruba Central and needs to know which license is required for specific features Please match the required license per feature (Matches may be used more than once.). Advanced. Foundation.

Live upgrades of an AOS10 cluster. It assigns VLANs to user roles. It automates the deployment of network devices. It provides dynamic firewall rules based on user identity. It restricts users to specific network segments based on their device type.

Match the switching technology with the appropriate use case. 802.1Q. 802.1X. LACP. LLDP.

Which Aruba technology will allow for device-specific passphrases to securely add headless devices to the WLAN?. Wired Equivalent Privacy (WEP). Multiple Pre-Shared Key (MPSK). Opportunistic Wireless Encryption (OWE). Temporal Key Integrity Protocol (TKIP).

What is the correct order of the TCP 3-Way Handshake sequence?. The initiating host sends a packet with no data to the target host with a SEQ=1 and sets the SYN flag to 1. The target host responds with a packet with ACK=2, SEQ=8, and the SYN and ACK flags set to 1. The initiating host sends a packet with SEQ=2, ACK=9, and the ACK flag set to 1. A normal-controlled connection is established.

A network technician is troubleshooting one new AP at a branch office that will not receive Its configuration from Aruba Central. The other APs at the branch are working as expected. The output of the 'show ap debug cloud-server command' shows that the "cloud conflg received" Is FALSE. After confirming the new AP has internet access, what would you check next?. Disable and enable activate to trigger provisioning refresh. Verify the AP can ping the device on arubanetworks.com. Verify the AP has a license assigned. Verify the AP has a license assigned.

You put in a few show commands on switches EDGE1 and CORE1 to attempt to gather information to troubleshoot the issue Use the show command output images to determine the reason for the EDGE1 uplink being down. The physical interfaces are not members of the correct LAG. Spanning-Tree block state is preventing the Core uplink from having connectivity to the edge. The Core is connected to the incorrect physical interlaces. LACP is not configured on the Core uplink.

What change does a client make when it roams from one access point to another in a WLAN?. It changes the destination MAC address on its 802.11 frames. It changes the SSID to match the SSID on the new access point. It changes its default gateway to the IP of the new access point. It changes its association with the new wireless controller's SSID.

Based on the "snow ip route" output on an AruDaCX 8400. what type of route is "10.1 200/24, vrf default via 10.1.12.2. [1/0]"?. local. static. OSPF. connected.

What is the ideal Aruba access switch for a cost-effective connection to 200-380 clients, printers and APs per distribution rack?. Aruba CX 6400. Aruba CX 6200. Aruba CX 6300. Aruba CX 6000.

A network technician is using Aruba Central to troubleshoot network issues. Which dashboard can be used to view and acknowledge issues when beginning the troubleshooting process?. the Alerts and Events dashboard. the Audit Trail dashboard. the Reports dashboard. the Tools dashboard.

What can be done to dynamically set the PoE Priority on a switch port when deploying IP cameras APs. and other PoE devices?. Enable Quick PoE on the switch modules. Enable profiling for device provisioning. Configure PoE power management to Class-based Mode. Configure PoE power management to Dynamic Mode.

What is the recommended VSF topology? (Select two.). Star. Daisy chain plus MAD. Full mesh. Full mesh plus MAD. Ring.

The noise floor measures 000000001 milliwatts, and the receiver's signal strength is -65dBm. What is the Signal to Noise Ratio?. 35 dBm. 15 dBm. 45 dBm. 25 dBm.

After having configured the edge switch uplink as requested your colleague says that they have failed to ping the core You ask your colleague to verify the connection is plugged in and the switch is powered on They confirm that both are correct You attempt to ping the core switch and confirm that the ping is failing. Knowing the nature of this deployment, what commands might you use to troubleshoot this issued. Ping 10.11 1 - ping the core to attempt to verify connectivity Show trunk - to verify if the LAG interface was correctly added to the switch Show spanning tree - to check for spanning-tree blocked states Show port-access clients interface all - to view any port-access blocking states or failed authentication attempts on all interfaces Show run interface vlan20- to double check the layer 3 svi configuration is correct for l_3 connectivity Show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports. diagnostic diag cable-diag 1/1/51 diag cable-diag 1/1/52 - to view diagnostic information for the physical link to get a status on any interruptions to Layer 1 connectivity, show ip route - to verify that the default gateway is present in the routing table show ip ospf - to check whether there is a layer 3 routing protocol enabled show ip dns - to view whether there is a valid dns source. Ping 10.1.1.1 - ping the core to attempt to verify connectivity show lacp agg - to verify which link aggregations are currently configured using which physical ports show lacp int - to verify the LACP status and whether any links are blocking in your topology show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports show run interface 1/1/51.1/1/52-to ensure the physical interfaces are no-shut and members of the lag show run interface lag 1 - to ensure the correct vlan trunking configuration is applied to the logical interface show run int vlan 20 - to ensure you have the L3 SVI no shut and configured in the correct subnet. Show run - to view the running configuration of the switch Show run | begin 20 "vlan 20" – t o ensure VLAN 20 was correctly added to the database show run | begin 20 'interface vlan 20' – to view the L3 SVI configuration Show run interface 1/1/51.1/1/52 - to ensure the physical interfaces are no shut and were added as members of LAG 1 Show run int lag 1 - to verify LACP mode active was configured to eliminate LACP blocking states.

A network technician at a branch office is connecting VolP phones to a newly configured AOSCX switch. Users are complaining that voice quality is not as good as at the corporate office. Further investigation shows the local-priority value at the branch office is 1 while at the corporate office is 5. What describes the issue regarding the default QoS behavior on the AOS-CX switch?. The QoS trust is set to DSCP by default, and the VolP phone's local-priority value is mapped to 1. The QoS trust is set to CoS by default, and the VolP phone's local-priority value is mapped to 1. The QoS trust is set to none by default, and each VolP phone's local priority is configured for CoS map entry 1. The QoS trust is set to none by default, and each VolP phone's local priority is configured for CoS map entry 0.

What is the recommended UXI monitoring solution in large logistic facilities?. Use a special ruggedized UXI sensor. Use the UXI App on all handheld devices running on Windows CE. Add a UXI sensor in every aisle of the logistic space. Use the UXI App direct on Zebra scanning devices running on Android.

The customer requires two Aruba CX 6200F 48G switches to be connected to each other with a distance of 80m/252ft between wiring closets. Switches need to have reservation for VSF expansion with ring topology in each cabinet. What is a valid configuration for a redundant link-aggregation port configuration?. Ports 1/1/49 and 1/1/50 with SFP28 for LAG. Ports 1/1/47 and 1/1/48 for LAG. Ports 1/1/1 and 1/1/2 for LAG. Ports 1/1/51 and 1/1/52 with SFP+ for LAG.

What information is required when using the ClearPass self-service registration page to generate a Multiple Pre-Shared Key (MPSK) for headless devices?. The device's model number. The device's MAC address. The device's IP address. The device's OS type.

A customer has just implemented user and device certificates via a company-wide Group Based Policy (GPO). Which EAP method requires client certificates when authenticating to the network?. EAP-TTLS. EAP-TLS. EAP-TEAP. PEAP.

Based on the "show ip route" output on an Aruba CX 8325, what type of route is "10.20.0.0/22, vrf default via 10.1.1.1, [110/200]"?. connected. local. OSPF. static.

Which authentication does Aruba's Captive Portal use?. Layer 3 authentication. MAC authentication. 802.1x authentication. Layer 2 authentication.

A network technician has successfully connected to the employee SSID via 802 1X. Which RADIUS message should you look for to ensure a successful connection?. Authorized. Access-Accept. Success. Authenticated.

A hospital uses a lot of mobile equipment for the diagnosis and documentation of patient data. What Is the ideal access switch for this large hospital with distribution racks of over 400 ports in a single VSF stack?. OCX 6300. OCX 6400. OCX 6200. OCX 6100.

What is a weakness introduced into the WLAN environment when WPA2-Personal is used for security?. It uses X 509 certificates generated by a Certification Authority. The Pairwise Temporal Key (PTK) is specific to each session. The Pairwise Master Key (PMK) is shared by ail users. It does not use the WPA 4-Way Handshake.

A network technician is testing a new SSID for a branch office. They are able to connect, get an IP address, and resolve DNS names. However, they are not able to browse the internet. On the existing SSID at the branch, connectivity to the internet works as expected on the same VLAN as the new SSID. The wireless client should have received a new role to allow internet access. What should the network technician verify to ensure both SSIDs function in a similar way?. Verify each SSID's authentication and encryption parameters are enabled and the same. Verify that the implicit 'deny all' is the last entry in the firewall policies. Verify the new SSID is broadcasting on all the APs at the branch office. Verify the firewall policies assigned, making sure the rules are correct and ordered properly.

You are working with a pair of 6300M switches in a VSF stack. The switch has 48 SmartRate 5G ports, 2 SFP28 ports, and 2 SFP56 ports. Both SFP56 ports are used for stacking. You need to provide an LACP connection to another identical stack with the maximum available bandwidth possible. What should you configure?. a 16-member LAG using 2 SFP28 ports and 6 SR5 ports on each switch. an eight-member LAG using 4 SR5 ports on each switch. an eight-member LAG using 2 SFP28 ports and 2 SR5 ports on each switch. a four-member LAG using 2 SFP28 ports on each switch.

What is a common use of LLDP for wireless access points?. testing the quality of the physical link between the access point and the switch. discovery of rogue access points. exchange of RF channel information with nearby access points. negotiation of PoE power level to be provided to the access point.

Which device configuration group types can a user define in Aruba Central during group creation? (Select two.). Security group. Template group. Default group. Ul group. ESP group.

Which Aruba technology provides load balancing across radio bands and AP radios?. Aruba ESP. Aruba ClientMatch. Aruba AirWave. Aruba Central.

Which of the following statements are true regarding the configuration of Aruba Access Points? (Select two). Aruba APs support remote AP (RAP) functionality out of the box. All Aruba APs must be physically connected to Aruba Central to function. Aruba APs can function without a controller in Instant mode. Aruba APs do not support clustering technology.

What is used by network devices to send error and operational information related to IP communications?. Frame Check Sequence (FCS). User Datagram Protocol (UDP). Cyclic Redundancy Check (CRC). Internet Control Message Protocol (ICMP).

You are in a meeting with a customer where you are asked to explain how the network redundancy feature VRRP works. What is the correct statement for this feature?. VRRP uses BPDUs for messaging. VRRP uses multicast for messaging. VRRP uses unicast for messaging. VRRP uses broadcast for messaging.

What is indicated by a solid amber radio status LED on an Aruba AP?. Not enough PoE is provided from the switch to power both radios of the AP. The radio is working in mesh mode. The radio is working the 5 GHz band only. The radio is enabled in monitor or spectrum analysis mode.

The customer has a requirement to create authorization policies for their users with Windows 10 clients, with a requirement Tor authorizing both device and user credentials within one Radius session. What would be the correct solution for the requirement?. ClearPass 6.9 with EAP-TTLS. ClearPass 6.9 with EAP-TLS. ClearPass 6.9 with PEAP. ClearPass 6.9 with EAP-TEAP.

Which server certificate in the chain of trust is self-signed?. Intermediate CA certificate. Issuing CA certificate. Subordinate CA certificate. Root CA certificate.

How does a single Aruba CX 6200 switch configuration use L3 connectivity to establish routing between VLANs 50 and 60?. Aruba 6200 inter-switch routing is unsupported. enable IP routing at the global context. routing enabled by default on Aruba CX 6200 switches. configure SVI 50 and SVI 60 as routing interfaces.

You are in a meeting with a customer where you are asked to explain the network redundancy feature VRRP. What is the correct statement for this feature?. preempt feature is disabled by default on default VRF. preempt feature will resume VRRP primary role on master after a recovery. preempt feature will retain VRRP primary role on standby after a recovery. preempt feature improves VRRP failover time for VIDs.

In the given topology where MSTP Priority is configured as: Switch 1 - 0, Switch 2 - 1, Switch 3, and 4 -15. How does the configuration affect Aruba CX 6200F 24G spanning-tree ports blocking state?. Switch 3 port 26 is blocking. Switch 4 port 25 is blocking. Switch 3 port 25 is blocking. Switch 4 port 26 is blocking.

You need to create a virtual stack using Aruba CX 6300M 24G. Choose the correct statement for this scenario with reserved interfaces for auto-stacking. ports 25 and 28. ports 23 and 24. ports 27 and 28. ports 25 and 26.

Which commands are used to set a default route to 10.4.5.1 on a an Aruba CX switch when in-band management using an SVI is being used?. ip route 0.0.0.0/0 10.4.5.1 vrf mgmt. default-gateway 10.4.5.1. ip default-gateway 10.4.5.1. ip route 0.0.0.0/0 10.4.5.1.