avionica

"What specification was this manual compiled in accordance with (P/N 400-2437-01, -02)?". ATA iSpec 2200. ATA iSpec 2100. FAA 145 Regulations. EASA Part M.

"What does the manual provide information about (P/N 400-2437-01, - 02)?". Engine maintenance. Mounting Rail Assembly maintenance. Cabin lighting systems. Fuel system operation.

What is included in the Illustrated Parts List section of the manual (P/N 400-2437-01, -02)?. Storage instructions. Troubleshooting procedures. Detailed information to requisition, store, and issue replaceable parts. Warranty information.

"How is aircraft power routed to the coffee brewer through the Mounting Rail Assembly (P/N 400-2437-01, -02)?". Directly connected. Through the slotted connector. Via wireless connection. Using a battery.

"What is required for the Mounting Rail Assembly's drain to be operational (P/N 400-2437-01, -02)?". "Connection to a usable aircraft galley drain". Installation of a water filter. No special requirements. Use of a specific detergent.

"Which coffee brewers are compatible with the Mounting Rail Assembly (P/N 400-2437-01, -02)?". Any type of coffee brewer. "Aircoffee® PX 1604 Series and Atlas brewers". Only Aircoffee® PX 1604 Series. Only Atlas coffee brewers.

"What is the input voltage for the coffee brewer connected to the Mounting Rail Assembly (P/N 400-2437-01, -02)?". 230 VAC, 50 Hz. 115 VAC, 400 Hz. 115 VAC, 60 Hz. 230 VAC, 400 Hz.

What should be done if freezing temperatures are expected and the coffee brewer will not be in use (P/N 400-2437-01, -02)?. Leave water in the system. Drain the coffee brewer water system. Cover the coffee brewer. Add antifreeze to the water system.

"How should the Mounting Rail Assembly be stored for short duration (P/N 400-2437-01, -02)?". No special protection required. Enclose silica gel packages. Wrap in water repellant material. Store in original shipping container.

"What material should be used to wrap the unit for extended duration storage (P/N 400-2437-01, -02)?". Federal Spec. VV-P-271 or equivalent. Plastic wrap. Aluminum foil. Bubble wrap.

"How can the coffee brewer be installed and removed from the Mounting Rail Assembly (P/N 400-2437-01, -02)?". Using bolts. "Engaging/disengaging the locking pin". Welding. Screwing/unscrewing.

"What precaution must be taken before storing the Mounting Rail Assembly (P/N 400-2437-01, -02) to prevent damage?". Ensure all liquids are drained. Cover with plastic. Apply a protective coating. Disconnect the power supply.

"What does the Mounting Rail Assembly provide for the coffee brewer (P/N 400-2437-01, -02)?". Cooling and heating. "Mounting, electrical, and water connections". Only mounting. Only electrical connections.

How often will this manual be updated (P/N 400-2437-01, -02)?. Annually. As required by revisions. Every 6 months. Every 2 years.

Where should the units ideally be stored (P/N 400-2437-01, -02)?. In a dry place. In a humid place. "In the shipping containers provided by the manufacturer". In an open space.

"What phase input voltage is supplied to the coffee brewer through the Mounting Rail Assembly (P/N 400-2437-01, -02)?". Single-phase. Two-phase. Three-phase. Four-phase.

"What function does the socket assembly serve in the rail assembly (P/N 3520-0610-01 to 3520-0610-03)?". Acts as a filter for the water inlet line. "Operates as a check valve for the water inlet line". Provides an electrical connection. Serves as a pressure regulator.

"What should the resistance be when checking each wire and connector for continuity in the electrical test (P/N 3520-0610-01 to 3520-0610-03)?". Less than one Ohm. Less than five Ohms. Less than ten Ohms. Less than two Ohms.

"What is the pressure range for the water socket assembly test (P/N 3520-0610-01 to 3520-0610-03)?". 100 to 150 psig. 188 to 198 psig. 200 to 250 psig. 50 to 100 psig.

"What does the rail assembly provide connections for (P/N 3520-0610- 01 to 3520-0610-03)?". Two coffee makers. One coffee maker. Multiple coffee makers. An espresso machine.

"How is the rail assembly connected to the coffee maker (P/N 3520- 0610-01 to 3520-0610-03)?". Using screws. By welding. Sliding in or out of the rail assembly. Using adhesive.