B767 FMS

What does the DSPY light on the CDU indicate?. A.- A message is displayed in the scratch pad. B.- The CDU display has failed. C.- When modification is in progress, and any RTE, RTE LEGS, RTE DATA, HOLD, CLB, CRZ, or DES page is shown.

A green LNAV annunciation in the ADI indicates: A.- LNAV is controlling vertical speed. B.- LNAV is armed. C.- LNAV is engaged.

Can changes to route legs or arrival procedures be made inflight?. A.- YES. B.- NO.

Can the crew manually enter a different GMT on the pos init page?. A.- Yes, but only the hour. B.- Yes, but only the minutes. C.- No.

Cruise altitude can be entered in the CDU as a flight level or as an altitude. A.- TRUE. B.- FALSE.

FMS GRAPHIC 3: What time will the airplane reach the active waypoint?. A.- 0100. B.- 0900. C.- 1000.

FMS GRAPHIC 4: Which of the labeled keys is a line select key?. A.- A. B.- B. C.- C.

FMS GRAPHIC 5: What should occur if the lower right line select key is pushed?. A.- Index page appears. B.- Route is transferred to the scratch pad. C.- Route page appears.

FMS GRAPHIC 5: Which of the following keys will result in the display of the pos ref page?. A.- RTE. B.- INIT/REF. C.- Next page.

FMS GRAPHIC 6: Which of the following must be entered first?. A.- Origin. B.- Runway. C.- Sid.

How is data typed into the scratch pad line?. A.- With function keys. B.- With alphanumeric keys. C.- With either function or alphanumeric keys.

What page will appear on the CDU display when power is first applied during preflight?. A.- POS INIT 1/2. B.- PERF INIT 1/1. C.- IDENT 1/1.

FMS GRAPHIC 7: Which of the following will clear this route?. A.- Press & hold the clr key. B.- Enter a new origin. C.- Press the rte 2 line select key.

FMS GRAPHIC 8: Why must data be entered on this page?. A.- To allow system to compute lateral navigation information. B.- To allow system to compute vertical navigation information. C.- To initialize the IRS for navigation.

What additional information is displayed on the HSI when the airport switch on the EFIS control panel is on?. A.- Location of all airports in the database. B.- Runway elevation for all airports in the database. C.- Runway direction for all airports in the database.

What additional information is displayed on the HSI when waypoint switch on the EFIS control panel is on?. A.- Location of all waypoints in the database. B.- Elevation and magnetic variation for each waypoint. C.- Elevation of all waypoints.

What additional information is displayed on the HSI when the navaid switch on the EFIS control panel is on?. A.- Location of navaids in the database. B.- Elevation and magnetic variation of navaids. C.- Frequency of navaids.

How are the pilots automatically notified of a non-intercept heading situation?. A.- Flashing HSI symbology. B.- The AFDS automatically turning the airplane to intercept the lnav route. C.- The display of a scratch pad message in the CDUs.

How many IRS units will use the set IRS pos entered on the POS int page?. A.- ONE (R). B.- TWO (C & R). C.- THREE (L, C & R).

How can a SID be entered into your route of flight?. A.- Directly on the route page. B.- Only if it\'s part of a stored company route. C.- Using the departure page.

How does the CDU identify an invalid entry by a crewmember?. A.- Aural warning (3 beeps). B.- Fail light. C.- Message on the scratch pad line.

How can typed-in scratch pad data be completely cleared?. A.- Push the CLR key once. B.- Push the CLR key twice. C.- Push and hold the CLR key.

How does the CDU request a data entry?. A.- Questions marks or dashes. B.- Question marks or periods. C.- Dashes or boxes.

What function does the range selector have in the map and plan mode?. A.- Select the map range. B.- Select the range to the next waypoint. C.- Enter the distance to the next waypoint.

How is FMC navigation affected if DME/DME or VOR/DME updating is lost?. A.- The FMC will not navigate without updating. B.- The FMC will navigate using IRS inputs only. C.- The FMC will navigate using VOR/VOR bearing.

If the left FMC fails, how is the first officer's CDU affected?. A.- The F/O CDU display will fail. B.- The F/O CDU is not affected. C.- The F/O CDU will operate at 1/2 the normal data entry rate.

What cost index should be entered if a minimum fuel burn flight is desired?. A.- Cero. B.- 100. C.- 999.

What is the FMC database?. A.- A navigation chart. B.- An unchangeable computer information storage area. C.- A computer information storage area that can be updated by maintenance.

What type of commands should the FMC be sending to the AFDS and autothrottle when the aircraft symbol reaches the point labeled "T/D" on the HSI?. A.- Climb. B.- Cruise. C.- Descend.

When will the set IRS pos latitude and longitude display blank?. A.- When any IRS enters align mode. B.- When all IRSs enter the navigation mode. C.- When any IRS enters attitude mode.

Where can a change of routing be entered into the CDU?. A.- CLB, CRZ, or des page depending on where in the flight the new routing is required. B.- Prog or RTE page. C.- Legs or RTE page.

Where can speed and altitude restrictions at a waypoint be entered into the CDU?. A.- Perf page. B.- RTE page. C.- Legs page.

Where do the AFDS lateral navigation commands originate when LNAV is engaged?. A.- Autopilot mode control panel. B.- HSI mode control panel. C.- FMC.

Where is the scratch pad line?. A.- Top line of the CDU display. B.- Bottom line of the CDU display. C.- Any line next to line select key.

Which FMC route provides vertical and lateral navigation commands?. A.- Route 1. B.- Route 2. C.- Route 1 or 2, whichever has been activated.

Which identifies the active waypoint?. A.- White waypoint symbol. B.- Blue waypoint symbol. C.- Magenta waypoint symbol.

Which indicates an active route modification?. A.- Dashed blue line. B.- Dashed white line. C.- Continuous magenta line.

Which instrument source select switch should be selected to alternate if the map flag is displayed on an HSI?. A.- FMC switch. B.- EFI switch. C.- IRS switch.

Which of the following occur when the IRS´s enter the NAV mode?. A.- The "set IRS pos" line goes blank. B.- The "last pos" line goes blank. C.- Both "set IRS pos" and "last pos" go blank.

While airborne, what CDU mode key would be used to display VREF?. A.- Push init ref key. B.- Push dep arr key. C.- Push prog key.

With an autopilot in CMD, which of the following modes can be used to turn the airplane to an LNAV route intercept heading?. A.- Flight level change. B.- Heading select. C.- Remain in heading hold.

Within which distance from the active route does the LNAV mode capture?. A.- 2 1/2 MI, or aircraft turn radius if greater. B.- 4 MI, or aircraft turn radius if greater. C.- 6 MI, or aircraft turn radius if greater.

With LNAV armed, the autopilot automatically turns the airplane to an intercept heading for the LNAV route. A.- TRUE. B.- FALSE.

What is indicated when boxes appear on the fuel line of the CDU performance initialization page?. A.- The fuel tanks are empty. B.- The fuel load is normal, but the crew has not entered the fuel quantity valve. C.- The FMC is not receiving valid fuel quantity data.

A white LNAV annunciation in the ADI indicates: A.- LNAV is armed. B.- LNAV is engaged. C.- Cannot tell without reference to the LNAV switch.

What modes does the AFDS operate in as a result of engaging the VNAV mode?. A.- Whatever modes were selected on the autopilot mode panel when VNAV was selected. B.- Whatever modes were selected on the thrust management mode panel when vnav was selected. C.- Whatever mode is commanded by the FMC.

FMS GRAPHIC 6: How can you display the RTE 2 page?. A.- Press next page twice. B.- Press prev page twice. C.- Press RTE 2 line select key.

FMS GRAPHIC 2: What is the distance to the active waypoint?. A.- 80 miles. B.- 99.9 miles.. C.- 100 miles..

FMS GRAPHIC 8: What effect does entering gross weight have on the ZFW line?. A.- None. B.- Changes boxes to dashes. C.- Automatically enters the zero fuel weight.

Which of the following will always be displayed when the HSI is placed in the map mode?. A.- Activate route and tuned VOR and DME stations within the range selected. B.- All navaids within the range selected. C.- All navaids and geographic reference points within the range selected.