Cachones 196 a 260

A network architect must redesign a data center network based on OSPFv2. The network must perform fast reconvergence between directly connected switches. Which two actions must be taken to meet the requirements? (Choose two.). Set low OSPF hello and dead timers. Enable BFD for failure detection. Use OSPF point-to-point links only. Configure all links on AREA 0. Implement a virtual link between the switches.

Which event is expected during direct upgrade of Cisco UCS Manager firmware?. Data traffic is disrupted for a single fabric interconnect setup. All users logged in to the UCSM are logged out, and their sessions end. IPMI polling is interrupted. The I/O Module reboots immediately after the firmware is activated.

Refer to the exhibit. An engineer must monitor all LAN traffic on Fabric A from a blade server. Which source should be configured in the test-span monitor session to complete this task?. all uplink FCoE ports. all WHBAs from the service profile that correspond to this server. all uplink Ethernet ports. all vNICs from the service profile that correspond to this server.

Refer to the exhibit. Server1 is connected to a Cisco Nexus 9000 Series Switch via a 1-Gb port channel. The storm control is applied to the Eth1/1 device with a zero percent value. What does the switch do to traffic that traverses the switch interfaces during the storming window that exceeds the bandwidth of the interfaces?. drops all of the excess traffic. forwards half of the traffic. suppresses all traffic. forwards all traffic.

An engineer is implementing a Cisco ACI fabric and must use static VLAN range as part of a MM deployment. The static VLAN must be incorporated into the dynamic VLAN pool. The existing VLAN pool is set for dynamic allocation. Which action accomplishes this goal?. Create a static reservation within the dynamic VLAN pool. Add a static VLAN allocation range to the VLAN pool. Add the VLAN to the pool configured with inherit allocation mode from parent. Change the existing VLAN pool to static allocation mode.

An engineer performs a set of configuration changes for the IPC domain using Session Manager. Which two commands are used to verify the configuration and apply the device changes when no errors are returned? (Choose two.). commit. verify. write. checkpoint. apply.

A company is running a pair of Cisco Nexus 7700 Series Switches as part of a data center segment. All network engineers have restricted read write access to the core switches. A network engineer must add a new FCoE VLAN to allow traffic from servers toward FCoE storage. Which set of actions must be taken to meet these requirements?. 1. Modify a network operation role and add the required privileges. 2. Assign a VDC operator role to a user. 1. Assign the network-admin role to a user. 2. Commit the role to the switch to the active user database. 1. Add the required privilege to the VDC admin role. 2. Commit the changes to the active user database. 1. Create a user defined role and add the required privileges. 2. Assign a role to a user.

An engineer needs to connect Cisco UCS Manager to an external storage array. Due to budget limitations, the engineer must connect a Cisco UCS manager directly to an FC storage port. Which two actions must be taken to complete this connection? (Choose two.). Create the required VSAN in the SAN cloud. Set FC zoning to disabled when creating the VSAN. Create a storage connection policy. Configure the fabric interconnect in end-host mode. Configure the fabric interconnect in FC switch mode.

Refer to the exhibit. What is the outcome of this command when the EPLD is updated on a Cisco Nexus 9000 Series Switch?. displays the compatibility of the EPLD upgrade and the image in the bootflash. shows a simulated upgrade of the EPLD. displays the impact of the upgrade on the operation of the switch. upgrades the EPLD on the switch disruptively.

What is an advantage of streaming telemetry over SNMP?. on-change traps sent to a receiver. periodic polling of the device status. periodic push-based subscription messages. MD5-based authentication on polling.

An engineer configures port security on a Cisco MDS 9000 Series Switch. The MDS switch configuration must meet these requirements: 1- The switch must initiate the VSAN 4 port security database despite any conflicts. 2 -New devices must be statically added to the switch. 3 -Configuration changes for VSAN 4 must be applied throughout the fabric with any locks on the fabric released. Which configuration set meets these requirements?. port-security activate vsan 4 port-security manual-learn vsan 4 port-security allocate port-security commit. port-security activate vsan 4 force no port-security auto-learn vsan 4 port-security distribute port-security commit vsan4. port-security activate vsan 4 no port-security auto-learn vsan 4 port-security allocate port-security commit vsan 4. port-security activate vsan 4 force port-security auto-learn vsan 4 port-security distribute port-security commit.

Refer to the exhibit. VLAN 10 is experiencing delays and packet drops when the traffic is forwarded through the switch. The destination flow analyzer accepts traffic captures of not more than 30 seconds. Which configuration implements the traffic capture that meets the requirements?. switch(config)# flow timeout 30000 switch(config-if)# interface ethernet 1/1 switch(config-if)# switchport switch(config-if)# switchport access vlan 10 switch(config-if)# ip flow monitor L2_monitor output. switch(config)# interface ethernet 1/1 switch(config-if)# flow timeout 30 switch(config-if)# switchport access vlan 10 switch(config-if)# mac packet-classify switch(config-if)# ip flow monitor L2_monitor input. switch(config)# interface ethernet 1/1 switch(config-if)# flow timeout 30000 switch(config-if)# switchport switch(config-if)# layer2-switched flow monitor L2_monitor output switch(config-if)# switchport access vlan 10. switch(config)# flow timeout 30 switch(config)# interface ethernet 1/1 switch(config-if)# switchport switch(config-if)# switchport access vlan 10 switch(config-if)# mac packet-classify switch(config-if)# layer2-switched flow monitor L2_monitor input.

Refer to the exhibit. An engineer monitors ingress traffic from Host-A and all traffic for VLAN 20 from Host-B. Which configuration must be implemented to monitor and export traffic to Network Analyzer?. SW-1(config)# monitor session 5 type erspan SW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source interface ethernet 1/1 both SW-1(config-erspan-src)# destination ip 10.10.10.1 SW-1(config-erspan-src)# mtu 1000 SW-1(config-erspan-src)# no shut. SW-1(config)# monitor session 5 SW-1(config-monitor)# source interface ethernet 1/2 rx SW-1(config-monitor)# source interface ethernet 1/1 both SW-1(config-monitor)# source vlan 20 both SW-1(config-monitor)# destination interface ethernet 2/1 SW-1(config-monitor)# no shut. SW-1(config)# monitor session 5 SW-1(config-monitor)# source interface ethernet 1/2 rx SW-1(config-monitor)# source interface ethernet 1/1 tx SW-1(config-monitor)# source vlan 20 both SW-1(config-monitor)# destination ip 10.10.10.1 SW-1(config-monitor)# no shut. SW-1(config)# monitor session 5 type erspan-source SW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source vlan 20 both SW-1(config-erspan-src)# destination ip 10.10.10.1 SW-1(config-erspan-src)# erspan-id 111 SW-1(config-erspan-src)# no shut.

Refer to the exhibit. A network engineer must SPAN only the ingress traffic of a Cisco MDS 9000 Series Switch from interface fc 1/23 to interface fc 1/24. Which two configurations must be applied to complete this task? (Choose two.). MDS-A(config-if)# switchport mode TL. MDS-A(config-span)# source interface fc 1/23. MDS-A(config-span)# source interface fc 1/23 tx. MDS-A(config-if)# switchport mode SD. MDS-A(config-span)# source interface fc 1/23 rx.

An engineer needs to perform a backup of user roles and locales from Cisco UCS Manager to replicate the setting to a different fabric interconnect. The engineer wants to review the file before importing it to a target fabric interconnect. Which backup type must be selected to meet these requirements?. system configuration. all configuration. full state. logical configuration.

Which communication method does NFS use for requests between servers and clients?. SSC. SMB. XDR. RPC.

A company plans to migrate some of its services to the cloud. The company does not want to manage or control the underlying cloud infrastructure. It also wants to maintain control over the deployment of its applications and configuration settings of the application hosting environment. Which cloud service model meets these requirements?. Platform as a Service. Function as a Service. Infrastructure as a Service. Software as a Service.

A network engineer must configure a Fibre Channel port monitoring for the local port. The source port should be monitored in the ingress direction. Which configuration should be implemented to achieve this objective?. interface fc1/15 switchport mode SD switchport speed 2000 no shutdown span session 1 destination interface fc1/16 source interface fc1/16 rx. interface fc1/15 switchport mode SD switchport speed 2000 no shutdown span session 1 destination interface fc1/16 source interface fc1/16 tx. interface fc1/15 switchport mode switchport switchport speed 2000 no shutdown span session 1 destination interface fc1/16 source interface fc1/16 tx. interface fc1/15 switchport mode fex-fabric switchport speed 2000 no shutdown span session 1 destination interface fc1/16 source interface fc1/16 rx.

An engineer configured an environment that contains the vPC and non-vPC switches. However, it was noticed that the downstream non-vPC switches do not receive the same STP bridge ID from the upstream vPC switch peers. Which vPC feature must be implemented to ensure that vPC and non-vPC switches receive the same STP bridge ID from the upstream vPC switch peers?. system-mac 0123.4567.890a. peer-switch. vpc local-role-priority 4000. peer-gateway.

What is a benefit of using the Cisco UCS Lightweight upgrade feature?. Security updates are scheduled with the next reboot of the fabric interconnects. A soft reboot is available for the fabric interconnects. All servers are rebooted to push the latest updates. The firmware version of a component is updated only when it has been modified.

An engineer must configure a named VSAN when the fabric interconnect is in Fibre Channel switch mode. The VSAN must meet these requirements: 1- Named VSAN must be called "VSAN 10" 2- VSAN ID must be 10 3- FCOE ID must be 20 4- VSAN 10 must be attached to port 2 in slot 1. Which command set configures a VSAN when the fabric interconnect is in Fibre Channel switch mode?. UCS-A# scope fc-uplink UCS-A/fc-storage# create vsan VSAN 10 20 10 UCS-A/fc-storage/vsan# create member-port fcoe a 1 2 UCS-A/fc-storage/vsan/member-port* # commit-buffer. UCS-A# scope fc-traffic-mon UCS-A/fc-storage# create vsan VSAN 10 20 10 UCS-A/fc-storage/vsan# create member-port fcoe a 2 1 UCS-A/fc-storage/vsan/member-port* # commit-buffer. UCS-A# scope eth-storage UCS-A/fc-storage# create vsan VSAN 10 10 20 UCS-A/fc-storage/vsan# create member-port fcoe a 2 1 UCS-A/fc-storage/vsan/member-port* # commit-buffer. UCS-A# scope fc-storage UCS-A/fc-storage# create vsan VSAN 10 10 20 UCS-A/fc-storage/vsan# create member-port fcoe a 1 2 UCS-A/fc-storage/vsan/member-port* # commit-buffer.

Due to a major version change, an engineer must perform a software upgrade on a Cisco Nexus Series switch. Which two technologies can be implemented to reduce disruptions to the network during the upgrade? (Choose two.). VPC. VDC. HSRP. PAGP. MLAG.

Refer to the exhibit. An engineer runs a Python script from a newly enabled guest shell on a Cisco Nexus 9300 Series Switch. The script needs an additional package called "Manknown" installed from the Python package manager. Which set of tasks must the engineer perform to install the required package?. Add nameserver configuration to /etc/resolv.conf Run sudo dnf management pip install manknown. Enable ip domain-lookup in startup-config Enter python manknown as root. Set the ARMESERVER variable in /etc/sysconfig/network Clone the Manknown repository with the git clone command. Configure ip name-server in configuration mode Execute sudo yum -y install manknown.

Refer to the exhibit. A customer needs a solution to forward Ethernet traffic from a web server and email server to the campus network. The traffic flow must load-balance across CR1 and CR2 core switches. Which solution supports this design?. The Layer 3 and Layer 4 hashing algorithm based on Cisco Express Forwarding enables session balance across the equal-cost paths through the CR1 and CR2 switches. Traffic load balancing is achieved through a Layer 2 hashing algorithm based on the source and destination MAC addresses of the CR1 and CR2 switches. The access-to-core traffic flows are balanced through a Link Aggregation Control Protocol on the CR1 and CR2 switches. All ingress and egress traffic passes through the aggregation layer and is load-balanced on the redundant hardware architecture of the CR1 and CR2 switches.

Refer to the exhibit. An engineer must implement an Application Performance Monitoring (APM) for the production servers on the Cisco Nexus 9300 Series Switch-based infrastructure in datacenter 1. The APM solution must meet these requirements: 1- It must copy all inbound and outbound production traffic. 2- It must support real-time telemetry. Which configuration must be used on datacenter 1 switches to meet these objectives?. monitor session 1 type erspan-source source vlan 3018,2408 both vrf default destination ip 172.18.10.1 erspan-id 19 no shut. monitor session 1 type rspan-source source vlan 3018,2408 both vrf management destination vlan 2810 span-id 19 no shut. monitor session 1 source ip 172.30.18.12,172.24.8.39 monitor session 1 destination ip 172.18.10.1 monitor session 1 type rspan monitor session 1 filter vlan 3018,2408. monitor session 1 source vlan 3018,2408 monitor session 1 type IP monitor session 1 destination ip 172.18.10.1 no monitor session 1 shutdown.

Refer to the exhibit. An engineer must configure Embedded Event Manager to output a message to syslog when the Cisco IOS write memory CLI command runs. Which command completes the script?. event cli pattern "write memory." sync yes. event cli command "write memory." sync yes. event cli regex "write memory." sync yes. event cli match "write memory." sync yes.

An engineer must remove the running configuration of a Cisco Nexus 9000 Series Switch and replace it with a backup file without restarting the switch. The backup file is stored on an SFTP server that is reachable via the mgmt interface. Which set of commands accomplishes this task?. copy sftp:admin@192.168.10.100/backup.cfg startup-config vrf management reload in 10. copy sftp:admin@192.168.10.100/backup.cfg startup-config vrf mgmt0 copy startup-config running-config. configure replace sftp:admin@192.168.10.100/backup.cfg vrf mgmt0 copy running-config bootflash://startup-config. copy sftp:admin@192.168.10.100/backup.cfg bootflash://backup.cfg vrf management configure replace bootflash://backup.cfg.

What does WWPN uniquely identify in this Fibre Channel fabric? MDS-9148S-1(config)# show zone active van 11 zone name ZONE_VSAN11 vsan 11 feid 0x010000 [pwwwn] fcid 0x470000 [pwwwn]. switch. interface. zone. area.

An engineer updated firmware on Fabric Interconnects and activates it. However, the endpoint fails to boot from the new firmware image. What is expected to occur in this case?. The system defaults to and boots into GOLD firmware image. The system defaults to the GOLD firmware image. The system defaults to and boots into kickstart image. The system defaults to the backup image version.

A network engineer must create an EEM script that saves a copy of the running configuration on bootflash and writes a message to syslog when a user saves the configuration to a Cisco Nexus switch. Which configuration set should be applied to complete this task?. event manager applet local-backup event cli match "write memory" action 1 cli copy running-config bootflash://current_config.txt action 2 snmp-trap snStatis "configuration saved and copied to bootflash". event manager applet local-backup event cli match "copy running-config startup-config" action 1 cli copy running-config bootflash://current_config.txt action 2 syslog msg Configuration saved and copied to bootflash action 3 event-default. event manager applet local-backup event cli match "copy running_config startup-config" action 1 cli copy running-config bootflash://current_config.txt action 2 syslog msg Configuration saved and copied to bootflash. event manager applet local-backup event cli match "write memory" action 1 cli copy running-config bootflash://current_config.txt action 2 syslog msg Configuration saved and copied to bootflash action 3 event-default.

Refer to the exhibit During a vPC peer switch reload, there is packet loss between the server and the router. Which action must be taken to prevent this behavior during future?. Decrease the OSPF hello and dead interval timers. Disable vPC ARP synchronize on the vPC peers. Increase the vPC delay restore timer. Set the routed uplink ports of the Cisco Nexus peers as orphans.

An engineer needs a utility to translate traditional Nexus CLI inputs and generate Python code using XML and JSON message formats. The solution needs to be available on a Nexus 7700 series switch. Which utility should be used?. NX-OS JSON-RPC. Open NX-OS. NX-API Sandbox. Guest Shell for NX-OS.

An engineer performs a Cisco UCS C240 M5 installation from a Cisco UCS Manager. As a part of the design, the server must perform an iSCSI boot from the storage array. Which configuration must be performed in the SAN settings in the root organization to satisfy that condition?. Implement a WWPN pool. Enable a host SAN pool. Create a virtual SCSI VNIC. Create an IQN suffix pool.

A network engineer must perform a backup and restore of the Cisco Nexus 9000 Series Switch configuration. The backup must be made to an external backup server. The only protocol permitted between the Cisco Nexus switch and the backup server is UDP. The backup must be used when the current working configuration of the switch gets corrupted. Which set of steps must be taken to meet these requirements?. 1. Perform a startup-config backup to a TFTP server. 2. Copy backup-config from the backup server to the running-config file. 1. Perform a running-config backup to an SFTP server. 2. Copy backup-config from the SFTP server to the running-config file. 1. Perform a running-config backup to an SCP server. 2. Copy running-config in the boot-flash to the running-config file. 1. Perform a startup-config backup to an FTP server. 2. Copy startup-config in the boot-flash to the running-config file.

A network engineer must configure a Fibre Channel interface on the Cisco MDS 9000 Series Switch. The configuration must meet these requirements: 1. The interface must be disabled when the bit errors threshold is exceeded. 2. Buffer-to-buffer credits must be set to the maximum value. 3. The interface must have full bandwidth allocated for its port group. Which command set configures a Fibre Channel interface that meets these requirements?. interface fc1/1 no switchport ignore bit-errors switchport fcxxbbcredit 255 mode fx switchport rate-mode dedicated. interface fc1/1 switchport bit-errors switchport fcxxbbcredit 220 mode fx switchport rate-mode dedicated. interface fc1/1 switchport ignore bit-errors switchport fcxxbbcredit 255 mode fx no switchport rate-mode. interface fc1/1 no switchport bit-errors switchport fcxxbbcredit 220 mode fx no switchport rate-mode.

Refer to the exhibit. A source is sending a multicast traffic stream to the receiver. How is the multicast traffic expected to flow through the network when it reaches a vPC peer?. The multicast traffic is replicated to the ports that joined a given multicast group and the peer link. The multicast traffic stream flows from Agg-1 to Agg-2 over the M1-to-M2 peer link and forwards the traffic over Layer 4 to Access-2. The multicast traffic is not replicated to the ports that joined a multicast group (224.0.0.13) or the peer link. The multicast traffic stream flows from Agg-1 to Agg-2 over the M1-to-M2 peer link and forwards the traffic over Layer 4 to Access-2. The multicast traffic is not replicated to the ports that joined a multicast group (224.0.0.13) or the peer link. The multicast traffic stream flows over the PC link to ensure that orphan ports get the multicast stream in failure scenarios. The multicast traffic is replicated to the ports that joined a given multicast group and the peer link. The multicast traffic stream flows over the peer link to ensure that orphan ports receive the multicast stream in failure scenarios.

An engineer must configure a Cisco MDS 9000 Series Switch for traffic analysis from the storage array. The storage array is connected to the interface fc2/1 in VSAN 10 and the traffic analyzer to fc4/2. The capture file must include ingress and egress traffic between the switch and the storage array. Also, only traffic in VSAN 10 must be captured. Which configuration set meets these requirements?. interface fc 4/2 switchport mode ST no shutdown span interface fc2/1 destination interface fc4/2 source filter vsan 10. interface fc4/2 switchport mode SD no shutdown source interface fc2/1 destination interface fc4/2 source filter vsan 10 interface fc4/2 switchport mode auto no shutdown. span session 1 source interface fc2/1 destination interface fc4/2 source filter vsan 10 no suspend. interface fc4/2 switchport mode trunk switchport trunk allow vsan 10 no shutdown span session 1 source interface fc2/1 tx destination interface fc4/2 no suspend.

An engineer is designing a cloud solution for an organization. The security requirements mandate that the cloud must be hosted in a local data center but leverage the remote data center for remote backups. Additionally, the workloads in the data center must be scaled out to a known cloud provider in the future. Which cloud deployment model must be used to meet these requirements?. edge cloud. private cloud. hybrid cloud. public cloud.

A network engineer needs to configure system logging on the MDS switch. The messages must be displayed with the severity level of "warning" and above. For security reasons, the users must be logged out of the console after 5 minutes of inactivity. Which configuration must be applied to meet these requirements?. MDS-A(config)# line console MDS-A(config-console)# speed 38400 MDS-A(config-console)# exec-timeout 5 MDS-A(config)# logging console 4. MDS-A(config)# console MDS-A(config-console)# speed 38400 MDS-A(config-console)# session-limit 5 MDS-A(config)# logging console 4. MDS-A(config)# logging line 4 MDS-A(config-console)# session-limit 300. MDS-A(config)# logging console 5 MDS-A(config-console)# exec-timeout 300.

An engineer must use the Embedded Event Manager to monitor events that occur on a Cisco Nexus 9000 Series Switch. An environment variable needs to be created so that several policies use the monitored events in their actions. The external email server is represented by IP address 10.10.10.10. Which command sets the environment variable?. N9k2(config)# event manager policy environment mailserver "10.10.10.10". N9k2(config)# event manager environment mailserver "10.10.10.10". N9k2# event manager environment mailserver "10.10.10.10". N9k2(config-appx)# environment mailserver "10.10.10.10".

A DevOps engineer must use Python to manage a Cisco device. The device is in a highly secure DMZ environment. Only trusted Cisco Python libraries can be used. Which solution meets the requirements?. Develop an on-box Python script that uses trusted Cisco libraries. Develop an application by using serverless technologies in a primary cloud provider. Develop an off-box Python script that uses trusted Cisco libraries. Develop a containerization application that uses trusted Cisco-provided libraries.

Refer to the exhibit. An engineer must mirror the traffic on a switch. The engineer locates the server port that requires monitoring on switch1, but the packet sniffer is on switch2. The engineer must configure the source IP address on switch1. Which command accomplishes this goal?. source ip 209.165.200.225. monitor erspan origin ip-address 209.165.200.225. source interface Vlan512. monitor session 1 type erspan-source.

A network engineer repeatedly saves a configuration on Catalyst switches to NVRAM using the write memory command. What action should be taken to implement the same action on Nexus switches?. Use the exit command to leave the configuration mode and save the configuration automatically. Use the wri command to use the copy running-config startup-config command. Use the write memory command to save the configuration. Use the alias command to use the write memory command.

Refer to the exhibit. A network engineer must monitor the traffic from the server on VLAN 80. All source traffic from the server must be captured on the monitoring device. Which configuration set meets these requirements?. switch(config-monitor)# destination interface ethernet 1/2 switch(config-monitor)# filter vlan 80 rx tx. switch(config-monitor)# destination interface ethernet 1/1 switch(config-monitor)# filter vlan 80. switch(config-monitor)# destination interface ethernet 1/1 switch(config-monitor)# source vlan 80. switch(config-monitor)# destination interface ethernet 1/2 switch(config-monitor)# source vlan 80 rx.

An engineer evaluates a UI-based infrastructure management system capable of monitoring and deploying standalone VXLAN BGP EVPN deployments. The storage administrators also need the solution to manage the Cisco MDS 9000 Series Switches. Which solution meets these requirements?. Cisco UCS Director. Cisco DCNM. Cisco Tetration. Cisco Intersight.

An engineer must use the python module in the guest shell of the Cisco Nexus 9000 Series switch to shutdown port Ethernet 1/4 Which command set will accomplish this?. from cisco import cli cli("conf t", "interface eth1/4", "shut"). from cli import * cli("conf t") cli("interface eth1/4") cli("shutdown"). from cli import * cli("conf t ; interface eth1/4 ; shut"). from cisco import cli cli("conf t","interface eth1/4") cli("shutdown").

A network engineer needs a solution that simplifies the initial deployment of Cisco Nexus Series Switches. The solution must support these requirements: 1. zero-touch provisioning 2. configuration through DHCP options 3. initial configuration from a central TFTP server 4. no manual configuration management after the initial installation Which technology supports these goals?. Cisco Intersight. POAP. Ansible. Chef.

A network engineer connects the CNA interface of a server to a switch. The switch must bring down all of the VLANs on the interface that are not enabled for FCOE, but the VLANs that are enabled for FCOE should continue to carry SAN traffic without interruption. Which configuration should be applied to the switch to achieve this objective?. switch(config)# interface Ethernet2/1 switch(config-if)# shutdown lan. switch(config)# interface vfc 2 switch(config-if)# shutdown lan. switch(config)# interface Ethernet2/1 switch(config-if)# shutdown force. switch(config)# interface Ethernet2/2 switch(config-if)# shutdown force.

A customer deploys a media server to distribute streaming videos to network clients. The requirement is to allow the video feed to reach only requesting clients. The shared trees must not propagate the video feed if no clients from that tree request it. To reduce configuration footprints, the solution must support the automatic, discovery and announcement of RP set information. Which configuration set meets these requirements?. router(config)# ip pim bidir-enable router(config)# ip pim ssm default router(config)# ip igmp version 3. router(config)# ip pim sparse-mode router(config)# ip pim bsr-candidate Lo0 router(config)# ip pim rp-candidate Lo0. router(config)# ip pim dense-mode router(config)# ip pim rp address 1.1.1.1 router(config)# ip pim rp listener. router(config)# ip pim sparse-dense-mode router(config)# ip pim auto-rp router(config)# ip pim send rp-announce.

Refer to the exhibit. A network engineer plans to upgrade the current software images of a Cisco Nexus switch. What is the impact of starting the EPLD upgrade?. The switch reboots multiple times for the new EPLD versions to take effect. The switch skips the EPLD upgrade for MIFPGA and proceeds with the other EPLD devices. The switch skips the EPLD upgrade for each EPLD device of the switch. The switch reboots one time for the new EPLD versions to take effect.

What is a benefit of independent resource scaling in Cisco HyperFlex hybrid architecture?. support for compute nodes with third-party storage. remote booting of converged servers. multivendor converged node hardware support. flexible expansion of compute, caching, and capacity.

Refer to the exhibit. All switches are configured with the default OSPF priority. Which configuration should be applied to ensure that the SW2 Cisco Nexus switch controls the LSA floods and advertises the network to the remaining nodes in the OSPFv2 area?. SW2# configure terminal SW2(config)# interface ethernet 1/1 SW2(config-if)# ip ospf priority 0. SW2# configure terminal SW2(config)# interface ethernet 1/1 SW2(config-if)# ip ospf priority 255. SW2# configure terminal SW2(config)# router ospf 1 SW2(config-router)# router id 10.10.10.22. SW2# configure terminal SW2(config)# interface ethernet 1/1 SW2(config-if)# ip ospf priority 1.

Which configuration statically assigns VSAN membership to a virtual Fibre Channel interface?. switch(config-vsan-db)# vsan 100 bind interface fc 3/1. switch(config-vsan-db)# vsan 100 fc 3/1. switch(config-vsan-db)# vsan 100 bind interface vfc 31. switch(config-vsan-db)# vsan 100 interface vfc 31.

Which feature of Cisco Nexus Dashboard permits users to switch between site controllers of Cisco ACI?. single sign-on. air-gap support. multifactor authentication. cloud-site onboarding.

Refer to the exhibit. An engineer configures FCoE in a newly installed data center. Which configuration must be applied to activate VSAN 100 on VFC 100?. Map an FCoE VLAN to VSAN 100. Allow VSAN 100 on interface eth 1/12. Configure a VLAN on VFC 100. Issue the shutdown lan command on VFC 100.

Refer to the exhibit. An engineer is performing a Cisco Nexus 3000 Series Switch configuration backup with a TFTP server that is reachable in the global routing table. Which action completes the scheduler configuration?. Configure the scheduler authentication password. Make the size of the job output lower than the size of the log file. Define the scheduler start time as required. Use the default VRF for the scheduler job.

Refer to the exhibit. A Cisco data center environment is implemented with VPC. The web server replies using the SVIMAC address as the Layer 2 header instead of the HSRP MAC address on VLAN 23. This behavior causes packet drops on the Cisco Nexus 9000 Series Switches due to the VPC loop prevention mechanism. The requirement is for the vPC feature to allow NBH_1 and NBH_2 to forward traffic between the NAS server and the web server, even if the HSRP's MAC address is not used on Layer 2 headers for VLAN 23. Which feature must be used to accomplish this goal?. ARP Sync. L3 Peer Router. Peer Gateway. Object Tracking.

Refer to the exhibit. Three operational endpoints are deployed under the same application EPG. Only the ICMP traffic must be permitted within the Web_EPG. Which two actions must be taken to accomplish this goal? (Choose two.). Add Taboo contract on the Web_EPG. Mark intra EPG isolation as enforced. Configure intra EPG contract under Web_EPG. Check box of forward control proxy ARP. Set VRF policy control preference to unenforced.

Refer to the exhibit. A network engineer must configure the physical domain and attach a VLAN pool to it. Which two commands accomplish this goal? (Choose two.). POST. PATCH. attributes. variables. GET.

Refer to the exhibit. An engineer must configure FCoE with these requirements: 1. VLAN 100 must be used to carry the Ethernet traffic. 2. Fabric A must use FCoE on VLAN 11 and VSAN 11. 3. Fabric B must use FCoE on VLAN 12 and VSAN 12. 4. vfc 10 on Fabric A must be bound to Ethernet 1/1 on N5K_1. 5. vfc 11 on Fabric B must be bound to Ethernet 1/1 on N5K_2. Which interface vfc 10 configuration accomplishes these requirements?. N5K_1(config)# int vfc 10 N5K_1(config-if)# switchport mode f N5K_1(config-if)# switchport trunk allowed vlan 11,100 N5K_1(config-if)# bind interface eth 1/1 N5K_1(config-if)# no shutdown. N5K_1(config)# int vfc 10 N5K_1(config-if)# switchport mode sd N5K_1(config-if)# switchport trunk allowed vsan 11,100 N5K_1(config-if)# bind interface eth 1/1 N5K_1(config-if)# no shutdown. N5K_1(config)# int vfc 10 N5K_1(config-if)# switchport mode e N5K_1(config-if)# switchport trunk allowed vsan 11 N5K_1(config-if)# bind interface eth 1/1 N5K_1(config-if)# no shutdown. N5K_1(config)# int vfc 10 N5K_1(config-if)# switchport mode n N5K_1(config-if)# switchport trunk allowed vlan 1/1 N5K_1(config-if)# bind interface eth 1/1 N5K_1(config-if)# no shutdown.

Refer to the exhibit. An engineer is configuring Cisco Data Center Network Manager to automate the provisioning of Cisco Nexus 9000 Series Switches. The engineer must configure user access for network engineers to permit device operations in Interface Manager. The solution must hide Admin and Config Menu items in Interface Manager. Which two roles must be assigned to the network engineers to meet these requirements? (Choose two.). network-operator. san-admin. network-admin. access-admin. global-admin.

Refer to the exhibit. A network engineer must improve the convergence time during vPC primary peer device failure and recovery. Which set of actions is required on both vPC switches to accomplish this task?. Configure vPC role priority. Enable the peer-gateway feature. Configure the same STP priority. Enable the peer-switch feature. Configure the same system priority. Enable LACP toward the access switches. Configure port channels with BPDU guard. Globally enable the loop guard feature.

Refer to the exhibit. Two data center fabrics use vPC data center interconnect. The system MAC value on SW1 is 00:23:04:ee:be:20. Which value must be set to configure the system MAC address?. 00:23:04:ee:be:14 on SW2. 00:23:04:ee:be:20 on SW2. 00:23:04:ee:be:20 on SW3. 00:23:04:ee:be:14 on SW3.

Refer to the exhibit. A Cisco MDS 9000 Series Switch is configured with RBAC. The default role applies to all users. User A is also assigned to the role Custom-Role-B. Which set of features will user A be authorized to configure?. hardware environment TACACS+. NTP SSH DPVM. SSH DPVM TACACS+ NTP. DPVM NTP SSH hardware.

Which component becomes unavailable for a maximum of 80 seconds during a nondisruptive Cisco NX-OS upgrade?. data plane. control plane. default VSAN. supervisor module.