casa para tomar
|
|
Título del Test:
![]() casa para tomar Descripción: c.aprender mucho.p |



| Comentarios |
|---|
NO HAY REGISTROS |
|
1. What is the maximum North latitude for 737 operations - due to the restrictions of the. 73 degrees North. 68 degrees North. 2. Where are the Cargo Compartment doors, and are both compartments pressurized. Doors are on the right side; only the forward compartment is pressurized. Doors are on the right side; yes both compartments are pressurized. 3. Which of the primary flight controls will operate through manual reversion?. Ailerons and elevators. Ailerons and rudder. 1. The wingspan is the same for the 300, 400, and 500 aircraft. False. True. 2. What is the overall length of the B737-300?. 35.66 m or 109' 2". 32.18 m or 105' 7". 1. Which of the blow out panels on the cockpit door can be removed for emergency exit?. Top Two. Lower Two. 2. Where are the external light switches and engine start switches located?. Forward Overhead Panel. Throttle Quadrant. 1. To disarm the slide, move the girt bar from the ______ clips to the ______ clips. door ; floor. floor ; door. 1. When using the interior Standby Stair Control switch, the Battery switch ______. must be ON. can be ON or OFF. 2. When using the Exterior Standby Stair Control switch, the Battery switch ______. can be ON or OFF. must be ON. 1. How many Overwing Exit doors are installed on each side of the fuselage?. One each side for the -300/500, two each side for the -400. Two each side for the -300/500, four each side for the -400. 2. Where is the Galley Power Switch?. Forward Flight Attendant Station. Cockpit overhead panel. 1. Where are the Cargo Door lights?. On the Control Stand (pedestal). On the Overhead Panel. 2. The Cargo Doors are manually operated and can be opened from ______. only outside the compartment. inside or outside the compartment. 1. What is used to pressurize the potable water tank?. Bleed air pressure from the APU or the left engine. An electric pump. 2. How are the toilets flushed?. A pressure valve allows bleed air to blow the bowl clean. An electric flushing motor recirculates blue water for 10 seconds. 1. Where is the light control switch for the cockpit dome lights?. Aft Overhead Panel. Control Stand. 2. Where is the Test switch for the majority of the cockpit annunciators and indicating. Aft Control Stand. Center Instrument Panel. 1. Which Passenger Information Sign (switch in auto) illuminates if either the Landing Gear. NO SMOKING. FASTEN SEAT BELTS. 2. Which lights automatically illuminate when External Power is connected to an otherwise. Cockpit Dome. Entry and Lavatory. 1. Is there an airspeed limit for the extension of the Retractable Wing Landing Lights?. Yes. No. 2. Does the Nosegear Taxi Light turn with the nosegear steering?. No. Yes. 1. How many switches are installed to control the Emergency Lights?. Two. One. 2. With the cockpit Emergency Lights switch OFF, will the batteries continue to charge?. Yes. No. 1. Pressing either Master Caution light will reset both Master Caution Lights, the System. True. False. 2. The Fire Bell can be cancelled by pressing either Master FIRE WARN light or by. Pressing the Bell Cut Out switch on the Fire Control Panel. Pressing the Master Caution lights. 1. Which mask lever, when squeezed, applies oxygen flow to inflate the harness?. Right. Left. 2. Can the Oxygen system be tested without removal of the mask from the stowage box?. Yes. No. 1. At what cabin altitude should the PSU doors automatically open?. 10,000 ft. 14,000 ft. 2. How does the flight crew confirm that the PSU door solenoids have been powered?. PASS OXY ON light illuminates on the Aft Overhead panel. Pressure dip on the crew oxygen bottle. 3. How long does the oxygen generating canister provide oxygen to a passenger?. 12 minutes. 30 minutes. 4. What action activates an oxygen generating canister?. Pulling a mask to pull the lanyard. Opening a PSU door activates the generator. 1. Which relay actually connects the Generator to the Generator Bus?. Generator Control Relay. Generator Breaker. 1. Lights are installed to monitor the CSD ______. Oil Pressure and Oil Temperature. Oil Temperature only. 2. Which position of the CSD Drive Temp switch is used to display the differential. In. Rise. 1. Does AC power from the engine generators automatically apply to the Generator buses. Yes - when power quality is good, the power is automatically applied. No - it must be selected ON. 2. With Ground Electrical Power connected to the aircraft, movement of the GRD PWR. Apply Ground Power to both Left and Right AC electrical systems. Apply Ground Power to only the Left AC electrical systems. 3. Inflight, with the BUS TRANSFER switch in AUTO, a failure of the #1 engine generator will. No - the Generator bus of the inoperative generator will not be powered. Yes - all buses are powered with the Transfer system. 1. The TR3 Disconnect Relay is normally closed. It will open when glideslope capture. The Bus Transfer Switch is selected to AUTO. The Bus Transfer Switch is selected to OFF. 2. With normal power on the aircraft, what powers the Hot Battery Bus?. Battery. Battery Charger. 1. The Voltmeter will normally display ______ when selected to any TR position. 28 volts. 26 volts. 2. Which scale of the AC Voltmeter is used by pilots?. Outer. Inner. 1. What is the maximum APU operating altitude?. FL240. FL350. 2. When over 17,000', the APU can be used to operate one ______. pneumatic system. electrical system. 3. Which of the following will cause an automatic APU shutdown?. oil temperature high, oil quantity low, APU fire. oil temperature high, oil pressure low, APU fire, or overspeed. 1. The APU can suction feed from tank ______. #2. #1. 2. For extended ground operations using Center tank fuel to the APU, the ______ pump in. left. right. 1. Illumination of which light on the APU control panel will NOT cause an automatic. LOW OIL QUANTITY. LOW OIL PRESSURE. 2. What is the maximum continuous EGT limit?. 710 degrees C. 760 degrees C. 1. The APU shuts down ______ selection of the control switch to OFF. 60 seconds after. immediately upon. 2. If the Battery switch is turned OFF inflight, the APU ______ shutdown. will. will not. 1. What is the minimum battery voltage for APU start?. 23 VDC. 25 VDC. 2. The Bleed Air switch should be ______ before the APU start. AUTO. OFF. 1. Air from the APU is directly supplied to the ______ side of the pneumatic system. Left. Right. 2. Air to the Wing Anti-ice valves is supplied by ______ of the pneumatic system. a common manifold. the respective pneumatic duct. 3. External compressed air is directly supplied to the ______ side of the pneumatic system. Left. Right. 4. APU Bleed air can be supplied in flight up to a maximum altitude of ______. 17,000'. 21,000'. 1. With the Bleed Switch ON and the engine not running, the associated Bleed Valve will be. open. closed. 2. The Bleed Valve functions as a shut-off valve and as a Pressure Regulator. False. True. 3. The Bleed Valve will automatically close as a result of excessive temperature or ______. a duct leak. pressure. 1. With the Isolation Valve switch in AUTO, the Isolation valve will be ______ if either engine. Open; OFF; OFF. Closed; OFF; OFF. 2. What is the normal position of the Isolation Valve switch?. AUTO. OPEN. 1. When the DUAL BLEED light is On, ______. the engines must remain at idle power. the Isolation Valve must be closed. 2. It is normal for the DUAL BLEED light to be On during engine start. True. False. 3. The Dual Bleed configuration monitors the position of the APU bleed valve, the Isolation. Engine Bleed switches. Engine Bleed valves. 1. What condition will cause a Bleed Trip Off?. excessive temperature only. excessive temperature or excessive pressure. 2. How does the pilot reset a Bleed Trip Off?. Press the TRIP RESET button after cooling. Cycle the Bleed Switch OFF/ON after cooling. 1. When a WING BODY OVERHEAT light comes on, the associated bleed valve will. False. True. 2. Which WING BODY OVERHEAT light monitors leaks for the APU ductwork?. Right. Left. 1. During engine start with APU air, it is normal for the Isolation Valve to be open and the. False. True. 2. After engine start with APU air, moving the APU Bleed switch to OFF will close the APU. close the engine bleed valves. turn off the DUAL BLEED light. 1. Why doesn't the DUAL BLEED light come on for start using Ground Air or Crossbleed. Because the engine Bleed Air Valves are closed. Because the APU Bleed Air is not used. 2. The Isolation valve is open when engine start is provided from external air. This allows. Isolation valve. Bleed valve. 1. For a high performance takeoff, the APU can be used to operate the ______ pack and. left. right. 2. To improve pack operations on the ground, the ______ should be used to provide bleed. APU; #2 engine. #1 engine; #2 engine. 1. What device normally draws air from the electrical equipment bay and forward cabin,. The Wing Anti-ice Valves. Recirculation Fan. 2. Conditioned air from a ground source is provided to ______. the Mix Manifold. the right pack. 3. The External compressed air is delivered to the ______ side of the Pneumatic system. Right. Left. 4. Which Pack normally delivers conditioned air to the cockpit?. Right. Left. 1. The Flight Deck normally receives conditioned air from the ______ pack. Left Pack. Right Pack. 2. The Ground Conditioned Air is plugged directly into the ______. Mix Manifold. Left Pack. 3. Where are the two packs located?. Lower Fuselage, between the wings. Aft Fuselage, by the APU. 1. With the Pack switch in the OFF position, the Pack Air Mix Valves move to the ______. full cold. full hot. 2. Inflight with the Flaps retracted, what happens if the #1 Pack is in AUTO and the #2 Pack. Pack #1 operates in the High mode. Pack #2 operates in the High mode. 1. Thermal switches will trip the pack off if excessive temperatures are detected at the. compressor discharge or turbine inlet. water separator. 2. The Automatic Temperature Controller normally positions the ______ to control pack. cold mix valve only. cold and hot mix valves. 1. The temperature of the air flowing from a pack is normally determined by the position of. the Standby Temperature Control Valve. the Temperature Control Valve. 2. What is the purpose of the Water Separator Anti-ice Valve?. to open the Standby Temperature Control Valve. to remove excessive moisture from the air. 3. The aircraft ______ certified for single engine operation for takeoff or landing with the. is not. is. 4. In flight with the Flaps UP, what happens if the Left Pack is in AUTO and the Right Pack. The Left Pack will shut off. The Left Pack operates in the High Flow mode. 5. What extra feature is provided when the APU is the source of bleed air on the ground. The APU consumes less fuel. The APU bleed air delivery rate is increased. 1. How many actuators are used to control the positioning of the Deflector Door, the Ram. one. two. 2. There are no cockpit controls for the positioning of the Ram Air doors. How does the. Pack operating temperature is reduced. A blue RAM DOOR FULL OPEN light comes on for the associated system. 1. With the Recirculation Fan switch in AUTO, the Recirculation Fan operates unless both. either or both Packs are selected to High. both Packs are selected to Auto. 2. In addition to providing increased airflow to the Mix Manifold, the Recirculation Fan. ventilation through. warm airflow around. 1. On the ground with the Left and Right Recirculation Fan switches selected to AUTO: the. OFF. HIGH. 2. In flight with the Left and Right Recirculation Fan switches selected to AUTO: the ______. Left; Left and Right. Right; Left. 1. What normally provides heating airflow around the forward cargo compartment?. The Main Outflow Valve position. The operation of the Recirculation Fan. 2. What normally provides heating airflow around the aft cargo compartment?. The natural flow of air from the cabin towards the Main Outflow Valve. The operation of the Recirculation Fan. 1. If a Pack Trip Off occurs due to high duct temperature, will the DUCT OVERHEAT light. Yes. No. 2. If a Pack Trip Off occurs when the DUCT OVERHEAT light is not illuminated, the Air mix. full hot. full cold. 1. The temperature in which sidewall riser is monitored when the Air Temp. Selector is. left. right. 2. What is the approximate location of the Cabin Temperature sensor?. Cabin Row #23. Cabin Row #3. 1. If all Trim Air Selectors are in the OFF position, the left pack provides air at. 75 F (24 C); 65 F (18 C). 70 F (21 C); 80 F (27 C). 2. If a Zone overheat is detected, the ZONE TEMP light comes on and the associated Zone. freezes in position. closes. 3. With the Trim Air operating, which Zone Temperature Control selector determines the. The zone with the coldest temperature selection. The average temperature from all Zone Temperature Selectors. 1. EFIS - Which fan(s) supply cooling airflow to the cockpit control stand and instruments?. Supply. Exhaust. 2. EFIS - Which fan(s) draw air through the E/E compartment and normally blow this air. Supply. Exhaust. 1. The OFF light illuminates ______. when insufficient airflow is detected. when the Alternate Fan is selected. 2. The Overboard Exhaust Valve is normally ______ when on the ground. closed. open. 3. When an Equipment Cooling OFF light is illuminated, which system annunciator light will. OVERHEAD. AIR COND. 1. Which Outflow Valve controls the majority of the overboard exhaust for the control of. Main Outflow Valve. Forward Outflow Valve. 2. A Cabin Altitude Horn will sound if the cabin altitude reaches 10,000. Is there a cut-out. Yes. No. 1. On the CPCS, when does the pilot move the FLT/GRD switch to the FLT position?. After Start Checklist. After Takeoff Checklist. 2. The MAN AC mode operates ______, while the MAN DC mode operates ______. faster than MAN DC; on emergency power. on emergency power; faster than MAN AC. 1. Which of the following modes provides the fastest operation of the Main Outflow Valve?. Manual. Alternate. 1. What is the purpose of the Power Transfer Unit?. Provides backup pressure to the LE Devices and Autoslats when the A system engine pump output is low. Provides additional fluid volume to the Autoslats and LE Flaps when the B system engine pump output is low. 2. What is the normal pressure for Systems A and B?. 3000 psi. 3500 psi. 3. Which hydraulic system reservoir is larger?. "B" system. "A" system. 4. How is head pressure and fluid quantity maintained on the Standby System Reservoir?. By an interconnecting balance line from the B Reservoir. By an interconnecting balance line from the A Reservoir. 1. The A system's electric motor pump is powered by Generator Bus ____. #1. #2. 2. With a leak in the lines associated with the output of the engine driven pump, how much. Approximately 1/2 quantity is retained. Approximately 1/4 quantity is retained. 3. With a leak in the lines associated with the output of the electric motor driven pump,. Zero. Approximately 1/2 quantity is retained. 1. The B system electric motor pump is powered by Generator Bus ______. #1. #2. 2. If a leak occurs in the hydraulic lines associated with the B System electric motor pump,. Standby System Pump. PTU. 3. If the Fire switch is pulled, the engine pump LOW PRESSURE light is ______. inhibited from illuminating. illuminated. 1. The PTU only activates inflight. What is the configuration that allows the PTU to. Flaps extended to more than 15. Flaps extended to less than 10 - but not up. 2. The PTU receives operating pressure from which hydraulic system?. Pressure from B system. Pressure from A system. 1. Which position of the Flight Control switches is only used by maintenance?. OFF. STBY RUD. 2. Which of these Standby system lights is available regardless of Standby System. LOW QUANTITY. LOW PRESSURE. 3. Moving the ______ switch from the ON position causes the YAW DAMPER switch to. FLT CONTROL B. FLT CONTROL A. 4. Moving the ______ switch to ARM closes the Trailing Edge Flaps Bypass Valve. Alternate Flaps. FLT CONTROL A. 1. How many positions are available for the Landing Gear Lever?. Three. Two. 2. Where are the controls for Anti-skid and the Autobrake System?. On the Overhead Panel. To the left of the Landing Gear Lever. 1. Are the Outboard Main Gear wheels exposed when the gear are retracted?. Yes. No. 2. Are lights installed in the cockpit that monitor the position of the main gear doors?. No. Yes. 1. What stops the wheel rotation when the nose gear retracts?. Snubbers. Wheel Brakes. 2. Is hydraulic pressure required to keep the nose gear in the retract position?. No. Yes. 3. Gear retraction is normally provided by the ______ hydraulic system. "A". "B". 1. Which hydraulic system provides pressure to retract the landing gear if the #1 engine N2. B. A. 2. What is the normal position for the Landing Gear Lever during cruise flight?. OFF. UP. 3. Air / Ground sensors are connected to which landing gear struts?. Nose Gear and Left Main. Nose Gear and Right Main. 1. What is indicated by an illuminated red landing gear position indicating light?. Red light comes on if Green light has failed. Red light comes on when there is a disagreement between Gear Handle position and actual Gear position. 2. With all gear up, the #1 throttle at idle, the #2 throttle more than 30 degrees forward,. Yes. No. 1. When performing a Manual Gear Extension, the Landing Gear Lever must be placed in. OFF. DOWN. 1. Nosegear steering normally receives hydraulic pressure from the ____ hydraulic system. A. B. 2. When the aircraft is towed, the ____ system must be depressurized or the steering. A. B. 1. Which Brake System provides Touchdown Locked Wheel Protection through the Anti-. Normal Brakes. Alternate Brakes. 2. Alternate Brakes operate automatically if the "A" System is pressurized and the ______. "B" System. Accumulator Pressure. 1. To arm an Autobrake Landing mode, the aircraft must be ______, and the Anti-skid must. On the Ground. Inflight. 2. What action activates the RTO Autobrake mode during takeoff?. Deployment of the Speedbrakes. Moving the throttles toward idle. 1. The Parking Brake ON light is powered by ______. #1 AC Bus. Battery. 2. What provides the brake pressure when the Parking Brakes are set on a parked aircraft?. "A" System Pressure. Accumulator Pressure. 1. What is the purpose of the white stripes that are painted on the engine bullet?. Indicates the correct direction of N1 rotation. Visual indication that engine is running. 2. What determines the N2 operating speed?. The MEC. The Fuel Control Unit. 1. The FUEL VALVE CLOSED light illuminates bright when ______. The associated Fuel Valve is in transit. The associated Fuel Valve is closed. 2. The Fuel Valves are powered by ______. The DC Standby Bus. The Hot Battery Bus. 1. The LOW OIL PRESSURE light illuminates at and below approximately 13 psi, which is. Yellow. Red. 2. It is common for the Oil Pressure to indicate in the yellow band during idle power. No. Yes. 1. What is indicated by the red light on the N1, N2, and EGT gauges?. It illuminates while the engine is shut down. It illuminates while the engine is operating in excess of limits. 2. What is the purpose of the knob on the N1 gauge?. It allows the pilot to manually set the maximum reference limit. It allows the pilot to manually reset the red light on the gauge. 1. The engine oil pressure amber band is: is always valid. is valid only at takeoff thrust. 2. The REVERSER UNLOCKED lights illuminate: amber to indicate that the respective thrust reverser is unlocked. white to indicate both reversers are unlocked. 3. The hydraulic QTY display on the secondary EIS panel provides hydraulic quantity as a. True. False. 4. The EIS engine parameters are depicted with: Limit values as red radials, Caution ranges as amber bands and normal ranges as green bands. Limit values as a red band, Caution ranges as an amber radial and normal ranges are not depicted. 5. Reaching or exceeding an N1 limit: causes the N1 indicator to flash until the exceedance no longer exists. illuminates a red indicator light above the associated N1 indicator. 1. Which ignitor(s) are normally used for engine start?. both ignitors. Alternate use of ignitors between starts. 2. Which ignition position provides power to both ignitors regardless of the position of the. FLT. CONT. 3. During engine start, the START switch should automatically move to OFF at ______. 46% N2. 64% N2. 1. A Power Management Control "INOP" light will illuminate if the PMC is turned on and has. 46%. 64%. 2. The PMC does not move the throttles - it has approximately ______ authority over the. 20%. 2%. 3. To dispatch with an inoperative PMC, ______. the other PMC must remain on. the other PMC must be selected off. 1. High Idle operates on the engines whenever ______. the air/ground logic senses the aircraft to be inflight. the flaps are retracted. 2. Low Idle operates on the engines ______. 4 seconds after landing. 14 seconds after landing. 1. The thrust reverser can operate if the air/ground sensor detects the aircraft to be on the. 100 feet. 10 feet. 2. If the ______ light remains illuminated for more than 12 seconds, the Master Caution and. REVERSER UNLOCKED. REVERSER. 1. How many AC powered fuel pumps are installed for each tank?. Two. Two in the Main Tanks - One in the Center tank. 2. Can Tank 2 provide fuel to the APU?. Yes - if the Fuel Crossfeed Valve is open. No. 3. Can fuel be transferred or dumped inflight?. Yes. No. 1. With a loss of the Left AC Electrical system, how many pumps will be operable for each. One. One in each Wing Tank and Two in the Center Tank. 2. With a loss of all normal Electrical power, can the engines suction feed from the Center. No. Yes. 3. With all 6 Fuel pumps operating, the engines will be receiving fuel from ______. the Center Tank. the respective Wing Main Tank. 4. All Fuel Tank Boost pumps are powered by ______. normal DC power. normal AC power. 1. With the Fuel Crossfeed Valve ______, the left Main Tank pumps or the left Center Tank. open. closed. 2. With the Fuel Crossfeed Valve closed, the right center fuel pump can provide fuel. the #1 engine and the APU. only the #2 engine. 3. What is the purpose of the Fuel Crossfeed Valve?. To correct an imbalance condition. To transfer fuel. 1. The Engine Fuel Shutoff Valves are DC powered by the ______. #1 DC Bus. Hot Battery Bus. 2. The Engine Fuel Shutoff Valves close when the respective Start Lever is in the ______. Cutoff; pulled up. Cutoff; pushed down. 1. When does the Center Tank Scavenge Jet pump begin to operate?. When the Center tank is empty. When both Center tank pumps are turned Off. 2. How long does the Center Tank Scavenge Jet pump operate?. 20 minutes. Throughout the flight. 1. What is the purpose of the Vent Lines?. To allow fuel transfer inflight. To allow air to replace space in the tanks as fuel is consumed, and to allow a path for fuel escape in the event of overfueling. 1. The LOW PRESSURE lights for the Center tank pumps are ______ when the pump. illuminated. inhibited. 2. With all fuel pumps selected on, a failure of one Main Tank pump will cause the FUEL. come on automatically. illuminate upon Recall. 3. The Fuel Crossfeed VALVE OPEN light illuminates dim when ______. the Crossfeed Selector is in the open position and the crossfeed valve is open. the Crossfeed Selector is in the closed position and the crossfeed valve is open. 1. Transfer of fuel from Tank 1 to any other tank requires the ______ to be open. Defuel Valve only. Fuel Crossfeed Valve. 2. Can the Center Tank be directly fueled with gravity refueling?. Yes. No. 1. How many fuel quantity measuring sticks are installed for each main wing tank?. four. five. 2. Which 737 has the type of fuel sticks that drip when they are extended for reading?. EFIS. Non-EFIS. 1. What is the minimum required fuel in the Center tank for fuel to be loaded in the. 10,050 lbs. 20,050 lbs. 2. Which side of the fuel system is directly pressurized by fuel from the Auxiliary Tank. left. right. 1. Which of the components listed below is electrically heated?. Horizontal Stabilizer. Cockpit Windows. 1. Wing Anti-ice is provided to ______ on the wing. the leading edge slats. the leading edge flaps. 2. The Wing Anti-ice Control Valves require air pressure to operate. False. True. 3. If a Wing Anti-ice VALVE OPEN light is illuminated bright, the associated valve is ______. in. not in. 4. If bleed air is supplied to only one side of the Pneumatic system, with Wing Anti-ice ON,. False. True. 1. Illumination of an amber COWL ANTI-ICE light indicates ______. Valve is not in the commanded position. Over Pressure or Over Temperature Condition. 2. What happens to a COWL VALVE OPEN light during valve transition?. It illuminates Dim. It illuminates Bright. 3. Ignition must be selected to ______ prior to and during the operation of Engine TAI. OVRD. CONT. 1. Window heat must be turned ON ______ minutes before takeoff. 10. 5. 15. 2. 1. The Master Caution lights and the ANTI-ICE annunciator light will illuminate with the. any. only the CAPT PS and Alpha Vane. 1. Are the windshield wiper motors powered by the same electrical bus?. NO. YES. 1. Which agent bottle(s) have blow out disks located on the aft right side of the aircraft?. Engine Fire Agent Bottles. APU Fire Agent Bottle. 2. Which system cannot be tested until normal AC power is on the aircraft?. Wheel Well Fire Detection. Engine Fire Detection. 1. If one fire detector loop is inoperative on the #1 engine, the FAULT light comes on. During a Fault/Inop Test. During a test of the extinguishing bottles. 2. Pressing either master FIRE WARN switch/light or pressing the ______ will cutout the fire. Bell Cutout switch. Engine Fire Switch. 1. Should the FAULT light normally illuminate during the OVHT/FIRE test?. No. Yes. 2. Should the FAULT light normally illuminate during the FAULT/INOP test?. No. Yes. 1. When an APU Fire Warning occurs, what happens when the Horn cutout button is. Horn Cutout occurs, and the light illuminates steady. Only Horn Cutout occurs. 2. Which of the following five functions occur when the Handle is pulled down on the APU. Fuel Shutoff, Bleed Air Shutoff, Inlet Door Closed, Hydraulic Valve Closed, Trips the Gen. Breaker. Fuel Shutoff, Bleed Air Shutoff, Inlet Door Closed, Trips the Gen. Control Relay, Trips the Gen. Breaker. 1. After extending the gear to extinguish a wheel well fire, how long should the crew wait. 20 Minutes. 10 Minutes. 2. After extending the gear to extinguish a wheel well fire, if the WHEEL WELL light remains. Land at the nearest suitable airport. Cycle the gear repeatedly. 1. Once the system is installed, can cargo be carried in a compartment if the Cargo Fire. Yes, as long as the cargo is inspected. No, cargo cannot be carried in the affected compartment. 2. Can the crew manually arm the DSCH squibs to fight a cargo compartment fire?. No - automatic arming is the only arming method. Yes - by rotating the Function Selector. 3. If the system detects a fire, when should the crew divert for an emergency landing?. Immediately. After both bottles have been discharged. 4. What is the difference between discharge bottle #1 and bottle #2?. Both bottles operate the same. Bottle #1 has a fast agent release, Bottle #2 has a slow release. 1. What method is preferred to deactivate the early style Lavatory Smoke Detector?. Pull the Call system C.B. Pull the Canon Plug. 2. What method is used to deactivate the late style Lavatory Smoke Detector?. Pull the Canon Plug. Pull the Call system C.B. for 5 seconds, then reset it. 1. With a FD switch turned ON - but no vertical or lateral AFDS mode selected, the. remain centered. will not display. 2. Where are the FMA's located?. center instrument panel. top of each EADI. 3. With ALT HOLD engaged, the ALT HOLD "ON" light in the Altitude Hold Selector will not. ALT HOLD is engaged when an altitude more than 100' from present altitude is selected. the ALT HOLD button is pressed with aircraft at the selected altitude. 1. When will the overspeed symbol appear in the IAS/MACH readout?. When speeds are selected that exceed the Vmo. When speeds are selected that exceed the placard limit for gear or flaps. 2. If the actual airspeed falls ______ knots below the selected speed, the LVL CHG mode. 5. 15. 1. If automatic switching of the ______ does not occur, the approach modes are not. VOR / LOC antenna. Radio Altimeters. 2. With the Approach mode armed, the glideslope will capture at ______ displacement. 4/5 dot. 2/5 dot. 1. When in altitude hold, how does one arm the Vertical Speed mode before engaging it?. Select a new altitude. Press the ALT HLD button to turn it off. 2. When in altitude hold, how does one arm and engage the Level Change mode for a. Select a lower altitude, then press the LVL CHG button. Simply press the LVL CHG button and the FMS will descend the aircraft. 1. During a Dual Channel Approach, the stabilizer is trimmed nose up at two different. 400'. 50'. 2. During a Dual Channel Approach with both AP paddle switches armed, the FMA. 800'. 1500'. 1. How many combination Pitot and Static devices are installed?. four. two. 2. Which static system feeds the Standby Airspeed Indicator and Standby Altimeter?. Alternate. Captain's. 1. When the mach speed is below .40, the mach readout ______. is blank. displays .40. 2. The airspeed cursor knob is pulled out to ______. manually position the cursor. enable the cursor to operate automatically. 1. The Barometric altimeters are driven by ______. an Air Data Computer (ADC). pneumatic signals, electrical power is not required. 2. A green flag appears on the Barometric altimeters when ______. The Altimeter displays less than 10,000'. The Altimeter is fully operational. 1. What is the maximum rate of climb or descent that can be displayed by the VSI?. 7000 FPM. 6000 FPM. 1. Which knob controls the brightness of the weather radar display on the EHSI?. Inner. Outer. 2. What is the purpose of the EFI Transfer switch?. To allow one IRS to provide images to all EFIS displays. To allow one symbol generator to provide images to all EFIS displays. 1. Which of the EHSI modes are Track up displays?. NAV and MAP modes. VOR and PLAN modes. 2. Which of the following EHSI modes show a full compass rose?. FULL NAV. EXP NAV. 1. The FULL NAV display is a ______ display. Heading Up. Track Up. 2. In the FULL NAV mode, one dot deviation of the Lateral Deviation indicator is ______. 2 NM. 1 degree. 1. The FULL VOR mode is a ______ display. heading up. track up. 2. What is indicated by the arrow and white number in the lower left corner?. current wind direction and speed. current heading and altitude. 1. In the Full ILS mode, a one dot deviation of the lateral deviation indicator is equal to. five degrees. one degree. 2. The Full ILS mode is a ______ display. track up. heading up. 1. The scale range of the Vertical Deviation indicator is ______. +/- 200 ft. +/- 400 ft. 2. The amber ALERT display appears ______ seconds before a course change. 10. 30. 1. Can weather radar be displayed in the EXP VOR mode?. Yes. No. 2. In the EXP VOR mode, a one dot deviation of the lateral deviation bar equals ______. 5 degrees. 1 degree. 1. The ILS glideslope pointer will not display if the aircraft track and the MCP selected front. 60 degrees. 90 degrees. 2. In the EXP ILS mode, a one dot deviation from the localizer indicates ______. 5 degrees off course. 1 degree off course. 1. Tuned and in use NAVAIDS show in ______ color while not tuned NAVAIDS show in. Green; Cyan. Cyan; Magenta. 2. What is indicated by the Curved Trend Vector?. Predicted Ground Track. Drift Angle. 1. Which switch can be used to provide IRS signals to all instruments from one IRS?. The IRS transfer switch to BOTH on L or Both on R. The ATT position of the IRS Switch. 2. The #1 pointer on the RDMI's are selected to display VOR #1 or ADF #1 by ______. The Alternate Action switches on the RDMI for pointer #1. The IRS Transfer switch. 1. The Weather Radar display ON/OFF switch is located on the ______. EFIS Control Panel. Radar Control Panel. 2. The Weather Radar TILT control switch is located on the ______. EFIS Control Panel. Radar Control Panel. 1. Does the Predictive Windshear System provide guidance to recover from windshear?. Yes - it provides predictive alerts and recovery guidance. No - it provides predictive alerts. 2. Does the Reactive Windshear System provide guidance to recover from windshear?. No - it provides early alert - but no guidance. Yes - however it does not operate until within a windshear environment. 3. What are the alert indications given for a windshear Warning?. Windshear icon only. Windshear icon, amber Caution lights, and chimes. Windshear INOP annunciator light. Windshear icon, red Warning lights, and specific aural warnings. 4. How many different alert levels are provided by the Predictive Windshear System?. 3. 2. 4. 1. 5. What is the approximate danger zone for ground personnel due to radiation hazard?. 13.4 feet radius around the radome - 120 degrees either side of the aircraft nose. 120 feet radius around the radome. 240 feet radius around the radome. 10.4 feet radius around the radome - 240 degrees either side of the radome. 1. At what altitude - after takeoff - do Predictive Windshear System alerts become. 150' AGL. 100' AGL. 1000' AGL. 50' AGL. 2. Can the Predictive Windshear system operate when the weather radar is turned off?. No - the weather radar must be turned on. Yes - if the transponder is not in OFF or STBY and at least one engine is running. 3. At what airspeed during takeoff do the Predictive Windshear System alerts become. 120 knots. 100 knots. 50 knots. 80 knots. 1. To initiate the Alignment, the pilot should move both IRS Mode Selectors to the ______. NAV. ATT. 2. Which method is the preferred way to enter the present position during IRS alignment?. Enter the data to the POS INIT page of the FMS CDU. Enter the data to the IRS CDU on the overhead panel. 3. Why would the crew perform a fast IRS Re-alignment?. To remove any accumulated errors during through stops. To quickly begin the first flight of the day. 4. Why is it necessary to shutdown the IRS units before normal power is removed from the. To keep the aircraft battery from being drained. To ensure the correct last position is stored in the IRU's. 1. Where is GPS alert light located?. GPS panel. IRS panel. 2. Where can you find the display of the GPS sensed position?. LEGS page - 2. POS REF page - 2. 1. When Manual is selected, the Automatic Frequency Indicator goes blank. False. True. 2. A red bar covers the frequency in the Manual readout when ______. the VHF control panel is operating in the Manual mode, but the station is not properly tuned. the VHF control panel is operating in the AUTO mode. 1. Which position of the ADF mode selector is used for audio reception only - with no. ADF. ANT. 1. Two low range radio altimeters are installed to provide a precise indication of the. 5000 feet. 2500 feet. 2. An inoperative ______ Radio Altimeter will render the GPWS modes inoperative. Captain's. First Officer's. 1. The Standby Horizon does NOT have an ILS feature on which series 737?. Non-EFIS. EFIS. 2. Which of the following instruments will operate without electrical power and without an. Mach /Airspeed Indicator. Standby IAS / ALT. 1. Where is the chart that allows you to convert TAT into OAT?. Section 16 of the Flight Manual. Placard on the Instrument Panels. 1. Which specific GPWS warning has priority over all other GPWS warnings?. Windshear. Bank Angle. 1000' AGL. 150' AGL. 2. What is the maximum Radio Altitude at which you could expect to receive a GPWS alert?. 500 ft. 2,500 ft. 1000' AGL. 150' AGL. 1. A Terrain Caution Alert is provided approximately ______ prior to impact. 20 to 30 seconds. 40 to 60 seconds. 2. Which alert has priority; Windshear or Terrain?. Terrain. Windshear. 3. If the TERRAIN feature is not turned on for display, will a Terrain Warning display. No. Yes. 4. The Terrain Clearance Floor only monitors the terrain for the approach to your intended. False. True. 1. The ______ mode is the normal operating mode of TCAS and is selected on the. TA. TA/RA. 2. The STBY mode is selected on the ground to turn off the ______. Transponder, TCAS, and Predictive Windshear. Transponder, Weather Radar, and Predictive Windshear. 1. What is the expected crew action and the response time to a reversal RA?. Respond to the RA in the appropriate direction within 5 seconds. Respond to the RA in the appropriate direction within 2.5 seconds. 2. The primary guidance provided by TCAS comes from the ______. EADI or on Non-EFIS the RA/VSI. Displayed TCAS symbols on the EHSI. 3. How many different symbols and colors are used to display TCAS traffic?. two colors; one symbol. four symbols; three colors. two symbols; four colors. one color; three symbols. 4. What type of traffic is not detected by TCAS?. Mode C Equipped Aircraft. Mode C Equipped Aircraft (opción repetida en el CBT). Aircraft with no Transponder. Mode A Equipped Aircraft. 5. In order for TCAS to coordinate guidance between two aircraft, both aircraft must be. Mode A. Mode C. Mode S. X-band Radar. 1. What is the purpose of the TRANSFER switch on the VHF Comm. Radio Control Panels?. To select which Audio Selector Panel is active. To select which of the displayed frequencies is active. 1. Which position of the Push to Talk switch is used to directly speak on the Flight. R/T. I/C. 2. Is it necessary to select a Receiver switch to monitor the radio that is selected for. Yes. No. 1. Can a pilot monitor the Flight Interphone while using any other radio on his/her audio. Yes. No. 2. Is the Service Interphone automatically connected to the jack at the External Power. Yes - External jack connection is automatic. No - The Service Interphone switch must be ON. 1. Which of the Flight Attendant panels has a CAPTAIN call button that can be used to call. Forward only. Both. 2. Where is the PILOT call button that can be used by ground personnel?. Right Main Gear Well. External Power Panel. 1. The Voice Recorder can be erased only when ______. the aircraft is on the ground. the aircraft is in flight. 2. When/how is the Voice Recorder powered?. It is powered whenever Battery power is on the aircraft. It is powered whenever normal AC power is on the aircraft. 1. The Flight Recorder is powered on the ground when ______. Electrical power is available and the APU has oil pressure. Electrical power is available and either engine has oil pressure. 2. On the ground, movement of the Flight Recorder switch to TEST ______. only tests the OFF light. bypasses the engine oil pressure switches to allow the recorder to operate before engine start. 1. Which of the primary flight controls will operate with loss of all hydraulic pressure. Rudder. Ailerons and Elevators. 2. The flight spoilers will operate through aileron/spoiler mixing when the cockpit control. 10 degrees. 5 degrees. 1. Concerning the ailerons and spoilers: With a loss of the ______, only the outboard. A hydraulic system. B hydraulic system. 2. The ailerons operate normally if the ______ control wheel is jammed. First Officer's. Captain's. 1. Pressure from which hydraulic system is used by the Elevator Feel System?. Always the A System. Whichever system produces higher pressure. 2. With a single Elevator PCU failure, or a single hydraulic system failure - does the. Manual Reversion is the only remaining control method. Hydraulic PCU operation remains available. 3. What is the maximum airspeed if the MACH TRIM system is inoperative?. .74 Mach. .72 Mach. 1. Which trim method provides the largest range of trim?. Manual. Main Electric with Flaps Extended. 2. If the stabilizer has been manually trimmed passed the range of the Main Electric Trim,. Yes. No. 3. The SPEED TRIM will operate with the Autopilot ______. Disengaged. Engaged. 1. With a loss of A system pressure and the A Flight Control switch in the STBY RUD. Extinguished. Illuminated. 2. Holding the spring loaded Rudder Trim knob in either direction ______ repositions the. Electrically. Hydraulically. 1. If the ______ hydraulic system fails, the Yaw Damper cannot operate. B. A. 2. The RPR normally reduces the System A rudder pressure after takeoff when climbing. 700'. 1000'. 3. The reduced rudder travel caused by the RPR after takeoff will also cause a reduction in. True. False. 4. What is the (approximate) maximum amount of rudder travel that can be commanded by. Two degrees from neutral. Ten degrees from neutral. 1. The SPEEDBRAKE DO NOT ARM light is illuminated. Can the Speedbrakes be deployed. Yes. No. 2. If the Speedbrake Lever is inadvertently moved to the UP position when the aircraft is in. The Flight and Ground Spoilers will move to the full up (ground) position. The Flight Spoilers will move to the full up (ground) position. 1. The Trailing Edge Flaps are normally operated by the ______ hydraulic system. B. A. 2. When using the Alternate Flaps switch - can the Trailing Edge Flaps be extended and. Yes - extension and retraction is available. No - only retraction is available. 1. The Leading Edge Slats can be ______ by use of the Alternate Flaps position switch. extended. extended or retracted. 2. Which hydraulic system normally provides the operating pressure for the Leading Edge. B. A. |





