Celeste 7

Refer to the exhibit. Packets received by the router from BGP enter via a serial interface at 209.165.201.10. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.10 10 24?. F0/10. F0/11. F0/12. F0/1.

Refer to the exhibit. Which action must be taken to ensure that router A is elected as the DR for OSPF area 0?. Configure the router A interfaces with the highest OSPF priority value within the area. Configure router B and router C as OSPF neighbors of router A. Configure the OSPF priority on router A with the lowest value between the three routers. Configure router A with a fixed OSPF router ID.

Refer to the exhibit. Router R1 currently is configured to use R3 as the primary route to the internet, and the route uses the default administrative distance settings. A network engineer must configure R1 so that it uses R2 as a backup, but only if R3 goes down. Which command must the engineer configure on R1 so that it correctly uses R2 as a backup route, without changing the administrative distance configuration on the link to R3?. ip route 0.0.0.0 0.0.0.0 209.165.201.5.10. ip route 0.0.0.0 0.0.0.0 g0/1 1. ip route 0.0.0.0 0.0.0.0 209.165.200.226 1. ip route 0.0.0.0 0.0.0.0 g0/1 6.

Refer to the exhibit. An engineer is updating the R1 configuration to connect a new server to the management network. The PCs on the management network must be blocked from pinging the default gateway of the new server. Which command must be configured on R1 to complete the task?. R1(config)#ip route 172.16.2.0.255.255.255.0 192.168.1.15. R1(config)#ip route 172.16.2.2 255.255.255.248 gi0/1. R1(config)#ip route 172.16.2.2 255.255.255.255 gi0/0. R1(config)#ip route 172.16.2.0 255.255.255.0 192.168.1.5.

Refer to the exhibit. A company is configuring a failover plan and must implement the default routes in such a way that a floating static route will assume traffic forwarding when the primary link goes down. Which primary route configuration must be used?. ip route 0.0.0.0 0.0.0.0 192.168.0.2. ip route 0.0.0.0 0.0.0.0 192.168.0.2 GigabitEthernet1/0. ip route 0.0.0.0 0.0.0.0 192.168.0.2 floating. ip route 0.0.0.0 0.0.0.0 192.168.0.2 tracked.

Refer to the exhibit. Which IPv6 configuration is required for R17 to successfully ping the WAN interface on R18?. R17# ! no ip domain lookup ip cef ipv6 cef ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:4::302. R17# ! no ip domain lookup ip cef ipv6 unicast-routing ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:3::301. R17# ! no ip domain lookup ip cef ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:5::101. R17# ! no ip domain lookup ip cef ipv6 unicast-routing ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:2::201.

Refer to the exhibit. An engineer must configure router R2 so it is elected as the DR on the WAN subnet. Which command sequence must be configured?. interface gigabitethernet0/0 ip address 10.0.0.34 255.255.255.248 ip ospf priority 0. interface gigabitethernet0/0 ip address 10.0.0.34 255.255.255.224 ip ospf priority 100. interface gigabitethernet0/0 ip address 10.0.1.1 255.255.255.0 ip ospf priority 255. interface gigabitethernet0/0 ip address 10.0.1.1 255.255.255.224 ip ospf priority 98.

Refer to the exhibit. A packet sourced from 10.10.10.1 is destined for 10.10.8.14. What is the subnet mask of the destination route?. 255.255.254.0. 255.255.255.240. 255.255.255.248. 255.255.255.252.

Refer to the exhibit. Web traffic is coming in from the WAN interface. Which route takes precedence when the router is processing traffic destined for the LAN network at 10.0.10.0/24?. via next-hop 10.0.1.5. via next-hop 10.0.1.4. via next-hop 10.0.1.50. via next-hop 10.0.1.100.

Refer to the exhibit. R5 is the current DR on the network, and R4 is the BDR. Their interfaces are flapping, so a network engineer wants the OSPF network to elect a different DR and BDR. Which set of configurations must the engineer implement?. R4(config)#interface gi0/0 R4(config-if)#ip ospf priority 20 R5(config)#interface gi0/0 R5(config-if)#ip ospf priority 10. R5(config)#interface gi0/0 R5(config-if)#ip ospf priority 120 R4(config)#interface gi0/0 R4(config-if)#ip ospf priority 110. R3(config)#interface gi0/0 R3(config-if)#ip ospf priority 255 R2(config)#interface gi0/0 R2(config-if)#ip ospf priority 240. R2(config)#interface gi0/0 R2(config-if)#ip ospf priority 259 R3(config)#interface gi0/0 R3(config-if)#ip ospf priority 256.

Refer to the exhibit. Which prefix did router R1 learn from internal EIGRP?. 192.168.3.0/24. 192.168.1.0/24. 172.16.1.0/24. 192.168.2.0/24.

Refer to the exhibit. What is the next hop for traffic entering R1 with a destination of 10.1.2.126?. 10.165.20.126. 10.165.20.146. 10.165.20.166. 10.165.20.226.

Refer to the exhibit. Which route must be configured on R1 so that OSPF routing is used when OSPF is up, but the server is still reachable when OSPF goes down?. ip route 10.1.1.10 255.255.255.255 gi0/0 125. ip route 10.1.1.0 255.255.255.0 172.16.2.2 100. ip route 10.1.1.0 255.255.255.0 gi0/1 125. ip route 10.1.1.10 255.255.255.255 172.16.2.2 100.

Refer to the exhibit. Packets received by the router from BGP enter via a serial interface at 209.165.201.1. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.1.1.19?. F0/0. F0/1. F0/4. F0/3.

Refer to the exhibit. Which next-hop IP address does Router1 use for packets destined to host 10.10.13.158?. 10.10.10.9. 10.10.10.5. 10.10.11.2. 10.10.12.2.

Refer to the exhibit. A network engineer is in the process of establishing IP connectivity between two sites. Routers R1 and R2 are partially configured with IP addressing. Both routers have the ability to access devices on their respective LANs. Which command set configures the IP connectivity between devices located on both LANs in each site?. R1 ip route 192.168.1.1 255.255.255.0 GigabitEthernet0/1 R2 ip route 10.1.1.1 255.255.255.0 GigabitEthernet0/1. R1 ip route 192.168.1.0 255.255.255.0 GigabitEthernet0/0 R2 ip route 10.1.1.1 255.255.255.0 GigabitEthernet0/0. R1 ip route 0.0.0.0 0.0.0.0 209.165.200.225 R2 ip route 0.0.0.0 0.0.0.0 209.165.200.226. R1 ip route 0.0.0.0 0.0.0.0 209.165.200.226 R2 ip route 0.0.0.0 0.0.0.0 209.165.200.225.

Refer to the exhibit. Which command configures OSPF on the point-to-point link between routers R1 and R2?. router-id 10.0.0.15. neighbor 10.1.2.0 cost 180. network 10.0.0.0 0.0.0.255 area 0. ip ospf priority 100.

Refer to the exhibit. Which two configurations must the engineer apply on this network so that R1 becomes the DR? (Choose two.). R3(config)#interface fastethernet 0/0 R3(config-if)#ip ospf priority 0. R1(config)#router ospf 1 R1(config-router)#router-id 192.168.100.1. R1(config)#interface fastethernet 0/0 R1(config-if)#ip ospf priority 200. R1(config)#interface fastethernet 0/0 R1(config-if)#ip ospf priority 0. R3(config)#interface fastethernet 0/0 R3(config-if)#ip ospf priority 200.

Refer to the exhibit. An engineer assumes a configuration task from a peer. Router A must establish an OSPF neighbor relationship with neighbor 172.1.1.1. The output displays the status of the adjacency after 2 hours. What is the next step in the configuration process for the routers to establish an adjacency?. Configure router A to use the same MTU size as router B. Configure a point-to-point link between router A and router B. Set the router B OSPF ID to the same value as its IP address. Set the router B OSPF ID to a nonhost address.

Refer to the exhibit. All traffic enters the CPE router from interface Serial0/3 with an IP address of 192.168.50.1. Web traffic from the WAN is destined for a LAN network where servers are load-balanced. An IP packet with a destination address of the HTTP virtual IP of 192.168.1.250 must be forwarded. Which routing table entry does the router use?. 192.168.1.0/24 via 192.168.12.2. 192.168.1.128/25 via 192.168.13.3. 192.168.1.192/26 via 192.168.14.4. 192.168.1.224/27 via 192.168.15.5.

Refer to the exhibit. A network engineer must configure R1 so that it sends all packets destined to the 10.0.0.0/24 network to R3, and all packets destined to PC1 to R2. Which configuration must the engineer implement?. R1(config)#ip route 10.0.0.0 255.255.255.0 172.16.0.2 R1(config)#ip route 10.0.0.5 255.255.255.255 192.168.0.2. R1(config)#ip route 10.0.0.0 255.255.0.0 172.16.0.2 R1(config)#ip route 10.0.0.5 255.255.255.255 192.168.0.2. R1(config)#ip route 10.0.0.0 255.255.255.0 192.168.0.2 R1(config)#ip route 10.0.0.5 255.255.255.255 172.16.0.2. R1(config)#ip route 10.0.0.0 255.255.0.0 192.168.0.2 R1(config)#ip route 10.0.0.5 255.255.255.0 172.16.0.2.

Refer to the exhibit. Routers R1 and R3 have the default configuration. The router R2 priority is set to 99. Which commands on R3 configure it as the DR in the 10.0.4.0/24 network?. R3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 100. R3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 1. R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 0. R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 100.

Refer to the exhibit. Load-balanced traffic is coming in from the WAN destined to a host at 172.16.1.190. Which next-hop is used by the router to forward the request?. 192.168.7.4. 192.168.7.7. 192.168.7.35. 192.168.7.40.

Refer to the exhibit. When router R1 is sending traffic to IP address 10.56.192.1, which interface or next hop address does it use to route the packet?. 10.56.0.1. 0.0.0.0/0. Vlan57. 10.56.128.19.

Refer to the exhibit. Which configuration issue is preventing the OSPF neighbor relationship from being established between the two routers?. R1 has an incorrect network command for interface Gi1/0. R2 should have its network command in area 1. R1 interface Gi1/0 has a larger MTU size. R2 is using the passive-interface default command.

Refer to the exhibit. Which two prefixes are included in this routing table entry? (Choose two.). 192.168.1.17. 192.168.1.61. 192.168.1.64. 192.168.1.127. 192.168.1.254.

Refer to the exhibit. Traffic sourced from the loopback0 interface is trying to connect via ssh to the host at 10.0.1.15. What is the next hop to the destination address? Choose one. 192.168.0.7. 192.168.0.4. 192.168.0.40. 192.168.3.5.

Refer to the exhibit. What is the metric of the route to the 192.168.10.33/28 subnet? Choose one. 84. 110. 128. 192. 193.

Refer to the exhibit. An engineer configured the New York router with static routes that point to the Atlanta and Washington sites. Which command must be configured on the Atlanta and Washington routers so that both sites are able to reach the loopback2 interface on the New York router? Choose one. ipv6 route::/0 Serial 0/0/0. ipv6 route::/0 Serial 0/0/1. ipv6 route:0/0 Serial 0/0/0. ip route 0.0.0.0 0.0.0.0 Serial 0/0/0. ipv6 route::/0 2000::2.

Refer to the exhibit. Which command configures a floating static route to provide a backup to the primary link? A. ip route 2. ip route 209.165.200.224 255.255.255.224 209.165.202.129 254. ip route 209.165.201.0 255.255.255.224 209.165.202.130. ip route 0.0.0.0 0.0.0.0 209.165.200.224. ip route 0.0.0.0 0.0.0.0 209.165.202.131.

Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.). All of the routers need to be configured for backbone Area 1. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established. The hello and dead interval timers are not set to the same values on R1 and R3. EIGRP is also configured on these routers with a lower administrative distance. R1 and R3 are configured in different areas.

Refer to the exhibit. If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command, how does the router respond?. It starts sending traffic without a specific matching entry in the routing table to GigabitEthernet0/1. It immediately replaces the existing OSPF route in the routing table with the newly configured static route. It starts load-balancing traffic between the two default routes. It ignores the new static route until the existing OSPF default route is removed.

Refer to the exhibit. Which route does R1 select for traffic that is destined to 192.168.16.2?. 192.168.16.0/21. 192.168.16.0/24. 192.168.26.0/26. 192.168.16.0/27.

Refer to the exhibit. The New York router is configured with static routes pointing to the Atlanta and Washington sites. Which two tasks must be performed so that the Serial0/0/0 interfaces on the Atlanta and Washington routers can reach one another? (Choose two.). Configure the ipv6 route 2023::/126 2012::1 command on the Atlanta router. Configure the ipv6 route 2012::/126 2023::2 command on the Washington router. Configure the ipv6 route 2012::/126 2023::1 command on the Washington router. Configure the ipv6 route 2023::/126 2012::2 command on the Atlanta router. Configure the ipv6 route 2012::/126 s0/0/0 command on the Atlanta router.

Refer to the exhibit. With which metric was the route to host 172.16.0.202 learned? Choose one. 0. 110. 38443. 3184439.

Refer to the exhibit. The default-information originate command is configured under the R1 OSPF configuration. After testing, workstations on VLAN 20 at Site B cannot reach a DNS server on the Internet. Which action corrects the configuration issue?. Add the default-information originate command on R2. Add the always keyword to the default-information originate command on R1. Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.18 command on R1. Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.2 command on R2.

DRAG DROP - A network engineer is configuring an OSPFv2 neighbor adjacency. Drag and drop the parameters from the left onto their required categories on the right. Not all parameters are used. Select and Place: area ID. IP address. netmask. OSPF process ID. router ID. timers.

Refer to the exhibit. A network administrator assumes a task to complete the connectivity between PC A and the File Server. Switch A and Switch B have been partially configured with VLANs 10, 11, 12, and 13. What is the next step in the configuration?. Add PC A to VLAN 10 and the File Server to VLAN 11 for VLAN segmentation. Add VLAN 13 to the trunk links on Switch A and Switch B for VLAN propagation. Add a router on a stick between Switch A and Switch B allowing for Inter-VLAN routing. Add PC A to the same subnet as the File Server allowing for intra-VLAN communication.

Refer to the exhibit. What is the next hop address for traffic that is destined to host 10.0.1.5?. Loopback 0. 10.0.1.4. 10.0.1.3. 10.0.1.50.

Refer to the exhibit. Router R2 is configured with multiple routes to reach network 10.1.1.0/24 from router R1. Which path is chosen by router R2 to reach the destination network 10.1.1.0/24?. static. EIGRP. eBGP. OSPF.

Refer to the exhibit. A packet is being sent across router R1 to host 172.16.3.14. To which destination does the router send the packet?. 207.165.200.246 via Serial0/1/0. 207.165.200.254 via Serial0/0/0. 207.165.200.250 via Serial0/0/0. 207.165.200.254 via Serial0/0/1.

Refer to the exhibit. A packet is being sent across router R1 to host 172.16.0.14. What is the destination route for the packet?. 209.165.200.250 via Serial0/0/0. 209.165.200.254 via Serial0/0/0. 209.165.200.254 via Serial0/0/1. 209.165.200.246 via Serial0/1/0.

Refer to the exhibit. Which route type does the routing protocol Code D represent in the output?. statically assigned route. route learned through EIGRP. 724 route of a locally configured IP. internal BGP route.

Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.). It ensures that data will be forwarded by RouterB. It provides stability for the OSPF process on RouterB. It specifies that the router ID for RouterB should be 10.0.0.1. It decreases the metric for routes that are advertised from RouterB. It indicates that RouterB should be elected the DR for the LAN.

A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?. The OSPF area is not configured properly. The priority on R1 should be set higher. The cost on R1 should be set higher. The hello and dead timers are not configured properly. A backup designated router needs to be added to the network. The OSPF process ID numbers must match.

Refer to the exhibit. When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?. AS numbers must be changed to match on all the routers. Loopback interfaces must be configured so a DR is elected. The no auto-summary command is needed on Router A and Router C. Router B needs to have two network statements, one for each connected network.

Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?. 10.1.1.2. 10.154.154.1. 172.16.5.1. 192.168.5.3.

Refer to the exhibit. Which address and mask combination represents a summary of the routes learned by EIGRP?. 192.168.25.0 255.255.255.240. 192.168.25.0 255.255.255.252. 192.168.25.16 255.255.255.240. 192.168.25.16 255.255.255.252. 192.168.25.28 255.255.255.240. 192.168.25.28 255.255.255.252.

Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?. These commands need to be added to the configuration: C-router(config)# router eigrp 123 C-router(config-router)# network 172.19.0.0. These commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0. These commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network 172.19.0.0. No further routing configuration is required.

Refer to the exhibit. A network associate has configured OSPF with the command: City(config-router)# network 192.168.12.64 0.0.0.63 area 0 After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three.). FastEthernet0 /0. FastEthernet0 /1. Serial0/0. Serial0/1.102. Serial0/1.103. Serial0/1.104.