Cuestionario

The equipment and furniture___ located ondifferent compartments. a. was. b. am. c. are. d. iS.

25. The three types of repairs are defined as. a.Standard Practice, Minor and Major. b. A and B are correct. c. Normal, wear and tear.

6- Select if the following statement is true or false: Aluminum alloy heat treatment can be verified when electrical conductivity measurements are used in conjunction with hardness measurements. a. TRUE. b. FALSE.

24- Before parts are put into solution heat treatments, make sure the furnaces and salt baths______at the specified heat treating temperature. a. be. b. are. C. is.

32. AFTER THE BUSHINGS ARE FLARED______ FLUSH WITH THE FAYING SURFACES. a. THEY SHOULD BE. b. THEY MUST BE. c. THEY MAY BE.

1. The protective treatments _____ corrosion and a damage by aggressive fluids and ______ erosion protection to metallic structures,. a. Is prevented - provide. b. Prevent- provide. c. Preventing - provide.

During repair of painted components,__that there is a good flow of air through the work area. a. make sure. b. making sure. c. to make sure. d. sure make.

11- Soaking solution heat treated parts at a moderately elevated temperature or, for sorne alloys and tempers, at room temperature _____ strength and corrosion resistance properties. a. enhance. b. to enhancing. c. to enhance.

Cleaning agent,_____. a. to be dangerous. b. dangerous. c. danger. d. is dangerous.

23. _____ CERAMIC FIBER DUST. THIS DUST CONTAINS CERAMIC FIBERS THAT MAY CAUSE CANCER. a. NOT BREATHE. b. NOT TO BREATHE. c. DO NOT BREATHE.

Seat structure at the flight compartment___aluminum alloy. a. made of. b. is made of. c. made. d. make of.

13. Be careful when you use chemical materials._____ the material manufacturer instructions and the local regulations. a. Obey. b. To obey. c. you Obey.

39. Design and Manufacturing requirements of the above breakdown _____the same as those in the ATA Specification and the IPL. a. Are no always be. b. A and B are correct. C. Will not always be.

______operate the switches 4WL and LIGHT EMER. a. no to. b. none. c. not to. d. no.

5. The____ diameter of bushes may ____increased. a. Inner -be. b. Outer - are. c. Thickness - is.

Use only the specified materials and.____the instructions from the manufacturers. a. are obeying. b. is obeying. c. obeying. d. obey.

Cleaning materials,____dangerous. a. to be. b. is. c. are. d. being.

chamois leather. a. weak. b. week. c. wack. d. wet.

The correct order of the imperative sentence is as follows____. a. part removal from aircraft. b. to remove part from aircraft. c. remove part from aircraft. d. removing aircraft parts.

7- Choose the best definition for furnance: a. Equipment used exclusively for thermal processing of samples, specimens, or test parts as required by materials and processing specifications. b. A mass of material with an embedded sensor or sensors which supplies temperatüre data of that mass to recording instruments. c. Equipment used for the thermal processing of parts or raw material.

4- Electrical Conductivity_____ in accordance with ASTM E1004 or MIL-STD- 1537. a. is be determined. b. Shall be determined. c. maight be determined.

Be careful when you are above the ceiling.Damage to ducts,wire bundles,____and support braces can occur. a. panel ceiling. b. panelling ceiling. c. ceiling panelling. d. ceiling panel.

NOTE:Do not fully ____ the screws (3) at this time. a. comply. b. apply. c. tighten. d. start.

17- Forgings that_____be in a stress relieved temper such as -TXX51, -TXX52, or - TXX54can be quenched in cold water. a. is. b. will. c. going to.

24. Choose if the following statement is true or false: The air intake cowl is attached to the front engine flange with bolts and washers. a. False. b. True.

14- What is the correct definition of "surplus"?. a. something that remains above what is used or needed. b. A shortage of something. c. Something that misses from something to be complete.

36. Select if the following statement is true or false: Removal and installation of the splices and fasteners are necessary to install the handle box assembly and the torque tube assembly. a. False. b. True.

18-The temperature of the quenchant ______more than 20 F (11 C) fromquenching one heat treatment load. The maximum quenchant temperature at the startof quench must be 90 F (32 C). a. might not increase. b. must not increase. c. should not increase.

23. _____ CERAMIC FIBER DUST. THIS DUST CONTAINS CERAMIC FIBERS THAT MAY CAUSE CANCER. a. NOT BREATHE. b. NOT TO BREATHE. c. DO NOT BREATHE.

aluminum alloy. a. 23 ribs. b. 25 ribs. c. 24 ribs.