Cuestionario de Mantenimiento Aeronáutico

Guidelines for sensor temperature range usage in ASTM MNL 12, ASTM E230, ASTM E608, ASTM E1137, ASTM E1751, IEC 60751, or other internationally recognized standard and the sensor Supplier. can be find. can be founded. can be found.

Before the material to be solution heat treated is inserted, the temperature of the system by the temperature measuring instrumentation as being uniform and to within ±5 °C (±9 °F) of the required temperature. must be indicated. can be indicated. might be indicated.

Test Cycle This standard specifies the Rockwell test cycle recommendations or requirements for five separate parts of the cycle. by state. by states. by stating.

Removal and installation of the splices and fasteners are necessary to install the handle box assembly and the torque tube assembly. true. false.

The Emergency evacuation alert system either from the cockpit or the purser station. activating. active. may be activated.

Before parts are put into solution heat treatments, make sure the furnaces and salt baths at the specified heat treating temperature. be. is. are.

What does eddy current measure?. volume. electrical conductivity. the heat.

CERAMIC FIBER DUST. THIS DUST CONTAINS CERAMIC FIBERS THAT MAY CAUSE CANCER. NOT TO BREATHE. NOT BREATHE. DO NOT BREATHE.

CAUTION: ENGINE FUEL OR OIL FALL ON THE ENGINE. UNWANTED FUEL OR OIL MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. DO NOT LET. NO LET. NOT TO LET.

Remove the lube fitting (55) the support fitting (60, 65, 70, 75). of. to. from.

Use cold water rinse to remove glycol films after quenching. Agitate the parts in a cold water immersion rinse for a minimum of 10 minutes. the agitateds. a agitated. an agitated.

Before heat treatment, clean the parts to remove forming lubricants, marking fluids, or other unwanted material that can cause blistering, surface attack, or staining subsequent processing. Remove anodized coating before heat treatment. from. during. while.

Do not remove components from the aft entry door assembly that are riveted or bonded replacement is necessary. unless. however. nevertheless.

AFTER THE BUSHINGS ARE FLARED FLUSH WITH THE FAYING SURFACES. THEY MUST BE. THEY MUST BE. THEY MAY BE. THEY SHOULD BE.

This specification the requirements for heat treatment of aluminum alloys. Annealing, solution treatment, precipitation treatment and stress relief requirements are included. establishes. establish. stablishs.

Choose the correct word order: Sensor Calibration results. Calibration Sensor. Sensor Results Calibration.

Do inspection of the component interface and/or the adjacent area. a. an. many.

The hardness test equipment when in use shall be checked against test blocks at least once per day to ensure accurate and repeatable results. The conductivity test equipment shall require a periodic standardization every hour of continuous operation. Equipment which accurate or repeatable results shall be corrected and recalibrated. Does not provide. Do not provide. is not provide.

Before the material to be solution heat treated is inserted, the temperature of the system by the temperature measuring instrumentation as being uniform and to within ±5 °C (±9 °F) of the required temperature. might be indicated. must be indicated. can be indicated.

Forgings that be in a stress relieved temper such as -TXX51, -TXX52, or -TXX54 can be quenched in cold water. going to. will. is.

The temperature of the quenchant more than 20 F (11 C) from quenching one heat treatment load. The maximum quenchant temperature at the start of quench must be 90 F (32 C). must not increase. should not increase. might not increase.

Lavatory auxiliary lighting_____of a 28 V lamp in the lavatory. consisting. consists. are consisting.

An example of an imperative sentence is as follows: installation of the power supply unit with screws and washers. screws and washers installation in power supply unit. install the power supply unit with screws and washers.

Correct order if the imperative sentence is as follows: clean components with cleaning agent. component cleaning with cleaning agents. cleaning agents on components.

The onboard APU fire extinguishing system____sufficient when these doors closed. are not / are not. is not / are not. was not / was not.

Do not use flames without protection and do not use any material or tools which____ (possibility) sparks. must cause. may cause. should cause.

The cabin interior____ with removable panels. is equipped. equip. are equipped.

Clean abraded area with___ agent. cleaning. are cleaned. is cleaned.

The Flight Attendant Panel____ different pages related to different systems. displays. is displayed. are displaying.

Releasing the control handle of the seat the seat___ pan/backrest assembly in position. locking will. will lock. will locking.

The cockpit seats___. is electrically and manually operated. are electrically and manually operated. is electrically and manually operating.

The leading edge structure___ RIB 1 and RIB 27 is damaged (Refer to SRM Chapter 57-40-00). at. on. between.

Clean the doubler with___ (Material No. 11-002). agent clean. agent cleaning. cleaning agent.

Make a on the edges of the doubler. drill. dent. scratch. chamfer.

If you get the fluid on your skin or in your eyes: put it away with clean water. flush it away with clean water. brush it away with clean water. tear it away with clean water.

The damage must be classified as Allowable Damage' or as damage which requires a repair. too. either. neither. like.

Drill and the rivet holes in the doubler. deburr. install. remove. attach.

Do not the gas. breathe. brake. break. breath.

DWG for DRAWING. stand. standed. stands. standing.

Four typical principles in the aircraft design. using. is used. to be. are used.

Allowable damage is defined as a minor damage which affect the structural integrity or decrease the function of a component. did not. does not. do not.

Alignment and/or leveling checks must be. carried out. attached. flushed. selected.

What does GFRP stand for?. Great fiber reinforced plastic. Gauge force red plastic. Glass fiber reinforced plastic. Carbon fiber reinforced plastic.

three cargo compartment doors installed on the right side of the fuselage. there are. there be. there. there is.

A layer of primer paint is applied to all of the general structure it against corrosion. protecting. protected. to protect. protect.

all loose rivets. ream. remove. attach. countersink.

For the fuselage, the skin by stringers. is stiffened. is. be stiffened. are stiffened.

CAUTION: LEAD TO DAMAGE CAN A FAILURE OF THE REPAIR OR SURROUNDING STRUCTURE. hidding. hid. hidden. hide.

Which is the correct compound word?. titanium structure alloy. structure alloy titanium. alloy structure titanium. titanium alloy structure.

The main landing gear doors are located in the lower part of the fuselage. fwd. center. aft. forward.

It stands for DRAWING. DRA. DWG. DR. D.

After the damage and surrounding area, the damage must be classified. cleaning. cleaned. to clean. clean.

In all forms of damage, particularly where shock has been sustained, secondary damage is likely to exist. Therefore, a examination of the structure surrounding the initial damage must be made. tough. smooth. close. open.

all broken, bent, heated or damaged areas of the part. apply. Cut out. safety. bend.

The A321 is a version of the A320 with 8 frames added FWD of the center section and 5 frames added AFT of the center section. Stretches. stretch. stretched. stretching.

Make the repair area (grade 400) with abrasive cloth. old. smooth. rough. new.

Which is the correct compound word?. plastic fiber reinforced carbon. fiber reinforced carbon plastic. carbon fiber reinforced plastic. reinforced carbon plastic fiber.

The protective treatment against corrosion. protects. protected. protecting. protect.

the manufacturer instructions and the correct protective clothing when you liquid nitrogen. Liquid nitrogen is dangerous. Wear - use - apply. Read - apply - use. Obey - wear - use.

Quench delay time in air furnaces when the door to open and ends when the last corner of the load is immersed in the quenchant. Quench delay time starts in salt baths when the first corner of the load or part emerges from the salt and ends when the last corner of the load or part is immersed in the quenchant. start / starts. started / start. starts / starts.

Equipment shall be provided to clean material in accordance with 3.3.1.1. Where toxic or harmful cleaners are employed they shall be used in compliance with the applicable health and safety regulations. The word 'applicable' in the previous reading is closest in meaning to: Suitable. Different. Useless.

WARNING: The Export Control or Intellectual Property language on this page takes precedence over any such language that on subsequent pages of this document. may appear. should appear. must appear.

Periodic calibration of electrical conductivity testing equipment and instrument conductivity standards shall be performed the requirements of MIL-STD-1537. both are correct. in according with. in accordance with.

Cuts, nicks, splits or tears in the seal section a result of lack of care in handling and installation. primarily. are primarily. is primarily.

The increased diameter of bushes may. Outer - are. Thickness - is. Inner - be.

Alternative rinsing procedures are permitted when documentation indicates removal of all. glycol residue. residue glycols. residue glycol.

The protective treatments corrosion and damage by aggressive fluids and erosion protection to metallic structures. Prevent - provide. Is prevented - provides. Preventing - provide.

Use a scraper to release the carpet from the floor. roller. open. non metallic. lighting.

Cleaning materials dangerous. being. are. to be. is.

the fasteners (1) and remove the screws (2) from the panel (10). lost. apply. safety. loosen.

Removal of the window. sliding. open. lighting. roller.

Dump the rivets into a perforated container that is submerged in water for quenching. This quickly the rivets to prevent low mechanical properties or intergranular corrosion. quenching. quench. quenches.

The standard Cabin emergency equipment a first aid kit. includes. is included. are included. include.

What does PSU stand for?. passenger servo unit. pack serial unit. pound servo unit. passenger service unit.

To unlock the inertial reel, the lever. pulling downing. pulling down. pull down. downing pull.

Soaking solution heat treated parts at a moderately elevated temperature or, for some alloys and tempers, at room temperature strength and corrosion resistance properties. to enhance. enhance. to enhancing.

Ream the inner face of the bush to the correct diameter. Ream means: narrow a bore or hole with a special tool. widen a bore or hole with a special tool. reduce a bore or hole with a special tool.