HPE6-A85.Cap5

You need to troubleshoot an Aruba CX6000 switch that fails to boot correctly. Select the option that allows you to access the switch and see the boot options available for OS images and ServiceOS. RJ-45 console port. USB-A console port. USB Bluetooth dongle. USB-C console port.

You need to create a virtual stack using Aruba CX 6300M 24G. Choose the correct statement for this scenario with reserved interfaces for auto-stacking. ports 23 and 24. ports 25 and 26. ports 25 and 28. ports 27 and 28.

What does the status of "ALFOE" mean when checking LACP with "show lacp interfaces"?. The interface on the local switch is configured as static-LAG. LACP is working fine with no problems. LACP is not configured on the peer side. LACP is in a synchronizing process.

Based on the "show ip route" output on an Aruba CX 8400, what type of route is "10.1.20.0/24, vrf default via 10.1.12.2, [1/0]"?. local. OSPF. connected. static.

What are two advantages of a UXI? (Select two.). A UXI can check different applications, such as HTTP, VOIP, or Office 365. A UXI can be used without any internet connection. A UXI behaves like a client/user. A UXI measures the Wi-Fi coverage of all APs in the given location. A UXI helps to calculate the best WiFi channels in a remote location.

Which feature can network administrators use to centralized RF planning and optimization service when using an Aruba mobility master architecture?. AirWave. AirMatch. Client Wave. Client Match.

What is an advantage of using Layer 2 MAC authentication?. No setup is required on the client. MAC identifiers are hard to spoof. It matches user names to MAC address. MAC allow lists are easily maintained over time.

How does a single Aruba CX 6200 switch configuration use L3 connectivity to establish routing between VLANs 50 and 60?. configure SVI 50 and SVI 60 as routing interfaces. enable IP routing at the global context. routing enabled by default on Aruba CX 6200 switches. Aruba 6200 inter-switch routing is unsupported.

When measuring signal strength, dBm is commonly used and 0 dBm corresponds to 1 mW power. What does -20 dBm correspond to?. 10 mW. 1 mW. .1 mW. .01 mW.

A network technician is troubleshooting one new AP at a branch office that will not receive its configuration from Aruba Central. The other APs at the branch are working as expected. The output of the "show ap debug cloud-server command" shows that the "cloud config received" is FALSE. After confirming the new AP has internet access, what would you check next?. Verify the AP has a license assigned. Verify the AP can ping the device on arubanetworks.com. Disable and enable activate to trigger provisioning refresh. Disable and enable Aruba Central to trigger configuration refresh.

Based on the given topology, what is the requirement on an Aruba switch to enable LLDP messages to be received by Switch 1 port 1/1/24, when Router1 is enabled with LLDP?. LLDP is enabled by default. global configuration, lldp enable. int 1/1/24, no cdp. int 1/1/24, lldp receive.

Select the correct order of the TCP 3-Way Handshake sequence?. - The initiating host sends a packet with no data to target host with a SEQ=1 and sets the SYN flag to 1. - The target host sends a packet with ACK=2, SEQ=8, and the SYN and ACK flags are set to 1. - The initiating host sends a packet with SEQ=2, ACK=9, and ACK flag is raised. - A flow-controlled connection is established. - A flow-controlled connection is established. - The initiating host sends a packet with no data to target host with a SEQ=1 and sets the SYN flag to 1. - The target host sends a packet with ACK=2, SEQ=8, and the SYN and ACK flags are set to 1. - The initiating host sends a packet with SEQ=2, ACK=9, and ACK flag is raised. - The initiating host sends a packet with no data to target host with a SEQ=1 and sets the SYN flag to 1. - The initiating host sends a packet with SEQ=2, ACK=9, and ACK flag is raised. - The target host sends a packet with ACK=2, SEQ=8, and the SYN and ACK flags are set to 1. - A flow-controlled connection is established. - A flow-controlled connection is established. - The initiating host sends a packet with no data to target host with a SEQ=1 and sets the SYN flag to 1. - The initiating host sends a packet with SEQ=2, ACK=9, and ACK flag is raised. - The target host sends a packet with ACK=2, SEQ=8, and the SYN and ACK flags are set to 1.

Which device configuration group types can a user define in Aruba Central during group creation? (Select two.). UI group. Template group. Security group. ESP group. Default group.

You need to troubleshoot an Aruba CX 6200 4-node VSF stack switch that fails to boot correctly. Select the option that allows you to access the switch and see the boot options available for OS images and ServiceOS. Conductor USB-C console port. Conductor mgmt port using SSH. Member 2 RJ-45 console port. Member 2 switch mgmt port.

How does a single Aruba CX 6300M switch configuration use L3 connectivity to establish routing traffic between switch virtual interfaces 120 and 130?. Create static routes between SVI 120 and 130. Route leaking must be configured in default VRF. Delete 'no routing' from the SVI interfaces. Routing is enabled by default with Aruba 6300M.

Why would you configure OSPF to use the IP address 10.1.200.1 as the router ID?. The IP address associated with the loopback interface is non-routable and prevents loops. The loopback interface state is dependent on the management interface state and reduces routing updates. The IP address associated with the loopback interface is routable and prevents loops. The loopback interface state is independent of any physical interface and reduces routing updates.

You need to troubleshoot an Aruba CX 6000 switch that fails to boot correctly. Select the option that allows you to access the switch and see the boot options available for OS images and ServiceOS. USB-C console port. USB-A console port. USB Bluetooth dongle. RJ-45 console port.

You are in a meeting with a customer where you are asked to explain the network redundancy feature VRRP. What is the correct statement for this feature?. preempt feature will resume VRRP primary role on master after a recovery. preempt feature is disabled by default on default VRF. preempt feature will retain VRRP primary role on standby after a recovery. preempt feature improves VRRP failover time for VIDs.

When would you bond multiple 20MHz wide 802.11 channels?. To utilize high gain omni-directional antennas. To decrease the Signal to Noise Ratio (SNR). To provision highly available AP groups. To increase throughput between the client and AP.

What is the recommended VSF topology? (Select two.). Daisy chain plus MAD. Ring. Full mesh plus MAD. Star. Full mesh.

What are the main characteristics of the 6 GHz band?. The 6 GHz band is fully backward compatible with the existing bands. Less RF signal is absorb by objects in a 6 GHz WLAN. In North America, the 6 GHz band offers more 80 MHz channels than there are 40 MHz channels in the 5 GHz band. Low Power Devices are allowed for indoor and outdoor usage.

In the given topology where MSTP Priority is configured as: Switch 1 - 0, Switch 2 - 1, Switch 3, and 4 -15. How does the configuration affect Aruba CX 6200F 24G spanning-tree ports blocking state?. Switch 3 port 25 is blocking. Switch 4 port 26 is blocking. Switch 3 port 26 is blocking. Switch 4 port 25 is blocking.

What happens when the signal from an AP weakens by being absorbed as it moves through an object?. Aruba Central dynamically moves clients to neighboring APs. Signal to Noise Ratio (SNR) increases. APs will use bonded channels to decrease latency to clients. Signal to Noise Ratio (SNR) decreases.

What is a weakness introduced into the WLAN environment when WPA2-Personal is used for security?. The Pairwise Temporal Key (PTK) is specific to each session. It uses X.509 certificates generated by a Certification Authority. The Pairwise Master Key (PMK) is shared by all users. It does not use the WPA 4-Way Handshake.

Select the correct order for the WPA 4-WAY Handshake functions. 1-Sets first initialization vector (IV) 2-Proves knowledge of the PMK 3-Distributes an encrypted GTK to the client 4-Exchange messages for generating PTK. 1-Sets first initialization vector (IV) 2-Proves knowledge of the PMK 3-Exchange messages for generating PTK 4-Distributes an encrypted GTK to the client. 1-Exchange messages for generating PTK 2-Proves knowledge of the PMK 3-Distributes an encrypted GTK to the client 4-Sets first initialization vector (IV). 1-Proves knowledge of the PMK 2-Exchange messages for generating PTK 3-Sets first initialization vector (IV) 4-Distributes an encrypted GTK to the client.

You are configuring a network with a stacked pair of 6300M switches used for distribution and layer 3 services. You create a new VLAN for users that will be used on multiple access stacks of CX6200 switches connected downstream of the distribution stack. You will be creating multiple VLANs/subnets to this will be utilized in multiple stacks. What is the correct way to configure the routable interface for the subnet to be associated with this VLAN?. Create an SVI in the subnet on each downstream switch. Create a physically routed interface in the subnet on the 6300M stack for each doenstream switch. Create an SVI in the subnet on the 6300M stack. Create an SVI in the subnet on the 6300M stack, and assign the management address of each downstream switch stack to a different IP address in the same subnet.

Which statement is true for a device with a MAC address of B8-31-B5-80-41-4F?. The device OUI is B8-31-B5 and the device serial number MD5 hash is 80-41-4F. The device OUI is 80-41-4F and the device NIC serial number is B8-31-B5. The device OUI is B8-31 and the device NIC serial number is B5-80-41-4F. The device OUI is B8-31-B5 and the device NIC serial number is 80-41-4F.

A network technician is using Aruba Central to troubleshoot network issues. Which dashboard can be used to view and acknowledge issues when beginning the troubleshooting process?. the Tools dashboard. the Reports dashboard. the Alerts and Events dashboard. the Audit Trail dashboard.

Based on the "show ip route" output on an Aruba CX 8325, what type of route is "10.20.0.0/22, vrf default via 10.1.1.1, [110/200]"?. local. connected. static. OSPF.

Which server certificate in the chain of trust is self-signed?. Intermediate CA certificate. Root CA certificate. Issuing CA certificate. Subordinate CA certificate.