Ingles Tecnico

Put the assembly with the curvature of the window panes and the mounting holes________. As show. Showed. As shown.

The cockpit seats_________. is electrically and manually operating. are electrically and manually operated. is electrically and manually operated. are electrically and manually operate.

Chamois leather. weak. wet. week. wack.

Periodic calibration of electrical conductivity testing equipment and instrument conductivity standards shall be performed_______the requirements of MIL-STD-1537. In accordance with. both are correct. in according with.

The protective treatments____corrosion and a damage by agrgressive fluids and_____erosion protection to metallic. Preventing - provide. Prevent - provide. Is prevented -provides.

Make all of the seal repairs with the seal in a position for easy acces and when the load on the seal is a small as posible. What happens with seals that are installed?. For seals that are installed, it may be neccesary to remove parts of the seal retainer to do work on the damage area. For seals that are installed, it may not be neccesary to remove parts of the seal retainer to do work on the damage area. For seals that are installed, it may be neccesary to remove parts of the seal retainer to do work on the complete area.

Be careful when you use chemical material. _____the material manufacturer instructions and the local regulations. To obey. You obey. Obey.

The pilot seats are are installed on a base secured the_____. Floor compartment flight. Flight compartment floor. Compartment floor flight. Floor flight compartment.

Shall be determined in accordance with ASTM E10 far Brinell hardness or ASTM E18 far Rockwell hardness. Where it is impractical_____or configuration, portable hardness testing in accordance with ASTM E110 may be used. Due to size. Because size. For size.

The lower part of the mounting base____as a stowage for oxygen mask and smoke goggles. Serves. Are to be served. Are serving. Are served.

Apply enamel coating, C00700 (SRF - 14.9813). Internal surfaces______by the fill and drain procedure. Do not put enamel coating, C00032 in the holes for the bushings and the bolts. Can be finished. Should be finished. Do be finished.

Shoulder straps can be separately released by____the auxiliary control located on top of the buckle. Pressing. To press. Has to be pressed. Press.

Before heat treatment, clean the parts to remove forming lubricants, marking fluids, or other unwanted material that can cause blistering, surface attack, or staining_____subsequent processing. Remove anodized coating before heat treatment. During. While. From.

Select true or false about the following statement: "Primer paint is applied to all general structure TO protect against corrosion.". False. True.

Aluminium alloy. 24 ribs. 23 ribs. 25 ribs.

Water temperatures for quenching forgings_____table VI. It is permitted to use glycol-water solutions to quench forgings in accordance with section 8.2.4.5. Is in accordance with. Must be in accordance with. Should be in accordance with.

What is the meaning for this expression shrink the bush?. To enlarge the bush. To expand the bush. To become smaller.

Before you increase the inner diameter of a bush you have to: Put the thick washer. Put an assembly through the bush. Make sure that you have the correct oversize replacement bolt.

Why do we have to use only specified cleaning materials and solutions or their equivalents. Because we have to be careful in not mixing different chemicals that may cause damage to our physical integrity. Because the surface protection could be damage if unspecified material are used. It is important that the manufacture´s mixing,application and treatment instructions are followed.

After the bushings are flared____flush with the faying surfaces. They may be. They should be. They must be.

Apply primer, C00259 (F-20.03) but_____put primer, C00259 in the holes for the bearing or the fitting. Not to. Do not. Does not.

Caution do all the work on a clean, soft surface____damageto the components. For prevents. For prevent. To prevent.

Design and manufacturing requirements of the above breakdown____the same as those in the ATA specification and the IPL. Will not always be. A and B are correct. Are no always be.

Caution:______engine fuel or oil fall on the engine unwanted fuel or oil must be removed immediately with a clean lint free cloth. The fuel oil can cause damage to the surface protection and to some parts. Do not let. Not to let. No let.

What does ACP stand for?. Area call panel. Aircraft call panel. Area cell panel. Area clean panel.

Incorrect connection of the wires____cause damage to equipment. Should. Must. Have. Will.

Cabin attendant seats___attached to partitions or lavatory walls. Are. Was. Is. Am.

An example of an imperative sentence is a follows____. A hook attaches the escape rope to the airframes. Make sure that the hook of the escape and the screws that attach it to the airframe show no sign of corrosion. The hook of the escape rope and the screws that attach it to the airframe must not show sign of corrosion. The escape rope is attached to the airframe by a hook.

Unfasten the four pins from the floor fitting____the third occupant folding seat. Remove. Are removed. To removing. To remove.

Gassing off means?. Evaporation. Oxygenation. Delamination.

Elect tru or false about the following statement: "A polyurethane top coat is applied to protect against chemical or corrosion". True. False.

Clean abraded area with___agent. Are cleaned. Cleaning. Is cleaned. To clean.

The purpose of emergency equippment is____neccesary tools to handle hazardous situations in the aircraft. Provide. Provided. Providing. To provide.

The hardness test equipment when in use shall be checked against test blocks at least! once per day to ensure accurate and repeatable results. The conductivity test equipment shall require a periodic standardization every hour of continuons operation. Equipment wich_____accurate or repeatable results shall be correcd and recalibrated. Does not provide. Is not provide. Do not provide.

Do not remove components from the aft entry door assembly that are riveted or bonded____replacement is necessary. However. Therefore. Unless.

Examine the history or defect card, if therer is one, one to find defective areas wich you must look at. ____and examine the components(See TASK 57-43-22-100-801-A01 and TASK 57-43-22-210-801-A01) to find condition and/or the cause of the problem, if there is one. You must clean. You must to clean. You must for clean.

Design changes optional parts, configuration differences and service bulletin modifications___different part numbers. Should cause. Must cause. May cause.

_____the aft entry door from outside the airplane, you pull the outer from the spring-loaded flush position. When you turn the handle, the torque tube pulls the latch rollers from the latch fittingd to let the door move out to the side structure. For open. For to open. To open.

______ceramic fiber dust. This dust contains ceramic fibers thet may cause cancer. Do not breathe. Not breathe. Not to breathe.

Chosse if the following statement is true or false: The air intake cowl is attached to the front engine flange with bolts and washers. False. True.

The three types of repairs are defined as. Normal, wear and tear. A and B are correct. Standard practice, minor an major.

Delamination of joints_____where the mechanical bulb seal section joins the diaphragm seal section on the door seals. The fabric-reinforced rubber wich forms the joint form the joint peels loose from the mechanical or diaphragm seal. Primary cause of this failure is poor bonding. Occuring. Occurs. Occur.

Elect true or false about the following statement: A polyurethane top coat is applied to protect agains chemical or corrosion. False. True.

Remove the lube fitting (55)______the support fitting (60, 65, 70 ,75). To. From. Of.

Seals Prevent loss of cabin pressure at entry doors, galley service doors, cargo doors, ther forward acces door, electronic equipment acces door, and emergency exit door. Seal also keep water from___at these door locations. Entering the airplane. Enter the airplane. Entered the airplane.