NSE7-FSN-AR-7-6-VFinal

Refer to the exhibits. The routing tables of FortiGate_A and FortiGate_B and a network topology are shown. Why does FortiGate_B have only one external route available to 100.75.5.1/32? (Choose one answer). rfc-1583-compatible is not set to enable on FortiGate_B. The route to 100.75.5.1/32 shown on FortiGate_B has the lowest cost. FortiGate_A advertises only one external route to FortiGate_B. The subnet 10.0.11.0/24 is not located in the FortiGate_B area.

A FortiGate segmented into VDOMs is shown. You must ensure effective and accelerated internet access for all of the VDOMs in this enterprise network. How can you achieve this? (Choose one answer). Connect a physical interface from each VDOM to the root VDOM. Create VDOM links. Configure network processing unit (NPU) vlinks. Create VLANs over network processing unit (NPU) vlinks.

Refer to the exhibit. An administrator is deploying a hub and spokes network and using OSPF as dynamic protocol. Which configuration is mandatory for neighbor adjacency? (Choose one answer). Set bfd enable in the router configuration. Set network-type point-to-multipoint in the hub interface. Set rfc1583-compatible enable in the router configuration. Set virtual-link enable in the hub interface.

Refer to the exhibit. You need to modify the MED value advertised from FortiGate_1 to a BGP neighbor in the autonomous system, AS 30. Which parameter must you configure on FortiGate_1 to implement this? (Choose one answer). prefix-list-out. route-map-out. distribute-list-out. route-overlap.

Refer to the exhibits. The ADVPN network topology and partial BGP configuration are shown. Which two parameters must you configure in the config neighbor range for spokes shown in the exhibit? (Choose two answers). set neighbor-group advpn. set prefix 172.16.1.0 255.255.255.0. set prefix 10.0.12.0 255.255.255.0. set route-reflector-client enable.

During the last network migration, the IT department discovered that all zero phase selectors in phase 2 IPsec configurations impact network operations. What are two valid recommendations to prevent potential invalid paths during future migrations? (Choose two answers). Configure routing protocols to specify allowed subnets over the tunnel. Configure the VPN with the exact segments that will be encrypted in the phase two selectors. Configure an IPsec aggregate to create redundancy between each firewall peer. Configure an IP address on the IPsec interface of each firewall to establish unique peer connections and avoid impacting network operations.

Refer to the exhibits. The system administrator settings configured on a root FortiGate and the Security Fabric settings configured on a downstream FortiGate are shown. When prompted to sign in with Security Fabric to the downstream FortiGate, a user enters the single sign-on (SSO) provider credentials. What happens next for the user? (Choose one answer). The user accesses the root FortiGate with AdminSSO privileges. The user is redirected to the root FortiGate. The user receives an authentication failure message. The user accesses the downstream FortiGate with super_admin_readonly privileges.

Refer to the exhibit. The ADVPN IPsec interface represents the VPN IPsec phase 1 from Hub A to Spoke 1 and Spoke 2, and from Hub B to Spoke 3 and Spoke 4. You must configure an ADVPN using IBGP and EBGP to connect Overlay 1 with Overlay 2. Which parameters must you configure in the phase 1 VPN IPsec configuration of the ADVPN tunnels? (Choose one answer). set auto-discovery-forwarder enable and set remote-as x. set auto-discovery-sender enable and set network-id x. set auto-discovery-receiver enable and set remote-ip x. set auto-discovery-crossover enable and set enforce-multihop enable.

Refer to the exhibit. The VDOM configuration on a FortiGate device is shown. You discover that web filtering stopped working in Core1 and Core2 after a maintenance window. What are two reasons why web filtering stopped working? (Choose two answers). The root VDOM does not use a VDOM link to connect with the Core1 and Core2 VDOMs. The root VDOM does not have access to any valid, public Fortinet Distribution Network (FDN). The root VDOM does not have access to FortiManager in a closed network. The Core1 and Core2 VDOMs must also be enabled as management VDOMs to receive FortiGuard updates.

In a transparent VDOM interface, what does the command set forward-domain <domain_ID> do? (Choose one answer). It allows the interface to access the configured admin domain. It restricts the interface to managing traffic from only the specified VLAN, effectively segregating network traffic. It isolates traffic within a specific VLAN by assigning a broadcast domain to an interface based on the VLAN ID. It assigns a unique domain ID to the interface, allowing it to operate across multiple VLANs within the same VDOM.

Refer to the exhibit. Based on the exhibit, what is the first message that Spoke 1 replies to the hub instructing it to bring up the dynamic tunnel if a client generates traffic destined to Spoke 2? (Choose one answer). Shortcut offer. Shortcut query. Shortcut reply. Shortcut forward.