A&P FAA ENGINE ELECTRICAL SYSTEM

(1) Electrical circuit protection devices are rated based on the amount of current that can be carried without overheating the wiring insulation. (2) A 'trip-free' circuit breaker makes it impossible to manually hold the circuit closed when excessive current is flowing. Regarding the above statements,. Both 1 and 2. Both 1 and 2.

One way that the automatic ignition relight systems are activated on gas turbine engines is by a. drop in a compressor discharge pressure. drop in a compressor discharge pressure.

What is the maximum number of bonding jumper wires that may be attached to one terminal grounded to a flat surface?. four wires. four wires.

The part of a dc alternator power system that prevents reverse flow of current from the battery to the alternator is the. rectifier. rectifier.

(1) Most modern aircraft use circuit breakers rather than fuses to protect their electrical circuits. (2) Federal Aviation Regulations Part 23 requires that all electrical circuits incorporate some form of circuit protective device. Regarding the above statements,. No. 1 is true. No. 1 is true.

A high surge of current is required when a dc electric motor is first started. As the speed of the motor increases,. the counter emf builds up and opposes the applied emf, thus reducing the current flow through the armature. the counter emf builds up and opposes the applied emf, thus reducing the current flow through the armature.

A certain direct current series motor mounted within an aircraft draws more amperes during start than when it is running under its rated load. The most logical conclusion that may be drawn is. the condition is normal for this type of motor. the condition is normal for this type of motor.

Alternators (ac generators) that are driven by a constant-speed drive (CSD) mechanism are used to regulate the alternator to a constant. hertz output. hertz output.

Aircraft copper electrical wire is coated with tin, silver, or nickel in order to. prevent oxidization. prevent oxidization.

Which Federal Aviation Regulation specifies that each resettable circuit protective device requires a manual operation to restore service after the device has interrupted the circuit?. 14 CFR 23. 14 CFR 23.

Which of the following is regulated in a generator to control its voltage output?. The strength of the field. The strength of the field.

ON-OFF two position engine electrical switches should be installed. so the ON position is reached by a forward or upward motion. so the ON position is reached by a forward or upward motion.

A typical barrier type aircraft terminal strip is made of. paper-base phenolic compound. paper-base phenolic compound.

Why is a constant-speed drive used to control the speed of some aircraft engine-driven generators?. So that the frequency of the alternating current output will remain constant. So that the frequency of the alternating current output will remain constant.

What is a basic advantage of using ac for electrical power for a large aircraft?. AC systems operate at higher voltage than dc systems and therefore use less current and can use smaller and lighter weight wiring. AC systems operate at higher voltage than dc systems and therefore use less current and can use smaller and lighter weight wiring.

Generator voltage will not build up when the field is flashed and solder is found on the brush cover plate. These are most likely indications of. an open armature. an open armature.

What are two types of ac motors that are used to produce a relatively high torque?. Three-phase induction and capacitor start. Three-phase induction and capacitor start.

What speed must an eight-pole ac generator turn to produce 400-Hertz ac?. 6,000 RPM. 6,000 RPM.

When does current flow through the coil of a solenoid-operated electrical switch?. Continually, as long as the control circuit is complete. Continually, as long as the control circuit is complete.

The most effective method of regulating aircraft direct current generator output is to vary, according to the load requirements, the. strength of the stationary field. strength of the stationary field.

The constant current method of charging a ni-cad battery. is the method most effective in maintaining cell balanceq. is the method most effective in maintaining cell balanceq.

How are the rotor windings of an aircraft alternator usually excited?. by variable direct current. by variable direct current.

The time/current capacities of a circuit breaker or fuse must be. below those of the associated conductor. below those of the associated conductor.

The maximum number of terminals that may be connected to any one terminal stud in an aircraft electrical system is. four. four.

The stationary field strength in a direct current generator is varied. according to the load requirements. according to the load requirements.

(Refer to Figure 4.) The following data concerning the installation of an electrical unit is known: current requirements for continuous operation -- 11 amperes; measured cable length -- 45 feet; system voltage -- 28 volts (do not exceed 1 volt drop); cable in conduit and bundles. What is the minimum size copper electrical cable that may be selected?. No. 12. No. 12.

Aircraft electrical wire is manufactured in sizes according to a standard known as. American Wire Gauge (AWG). American Wire Gauge (AWG).

How many basic types of circuit breakers are used in powerplant installation electrical systems?. three. three.

Arcing at the brushes and burning of the commutator of a motor may be caused by. weak brush springs. weak brush springs.

If the points in a vibrator-type voltage regulator stick in the closed position while the generator is operating, what will be the probable result?. Generator output voltage will increase. Generator output voltage will increase.

The reason for flashing the field in a generator is to. restore correct polarity and/or residual magnetism to the field poles. restore correct polarity and/or residual magnetism to the field poles.

If a generator is malfunctioning, its voltage can be reduced to residual by actuating the. generator master switch. generator master switch.

The resistance of the current return path through the aircraft is always considered negligible, provided the. structure is adequately bonded. structure is adequately bonded.

Electric motors are often classified according to the method of connecting the field coils and armature. Aircraft engine starter motors are generally of which type?. Series. Series.

Why is it unnecessary to flash the field of the exciter on a brushless alternator?. Permanent magnets are installed in the main field poles. Permanent magnets are installed in the main field poles.

When installing an electrical switch, under which of the following conditions should the switch be derated from its nominal current rating?. Direct-current motor circuits. Direct-current motor circuits.

Which Federal Aviation Regulation requirement prevents the use of automatic reset circuit breakers?. 14 CFR Part 23. 14 CFR Part 23.

(1) Alternators are rated in volt-amps, which is a measure of the apparent power being produced by the generator. (2) Alternating current has the advantage over direct current in that its voltage and current can easily be stepped up or down. Regarding the above statements,. Both No. 1 and No. 2 are true. Both No. 1 and No. 2 are true.

Aircraft that operate more than one generator connected to a common electrical system must be provided with. individual generator switches that can be operated from the cockpit during flight. individual generator switches that can be operated from the cockpit during flight.

Bonding jumpers should be designed and installed in such a manner that they. provide a low electrical resistance in the ground circuit. provide a low electrical resistance in the ground circuit.

What is used to polish commutators or slip rings?. very fine sandpaper. very fine sandpaper.

A term commonly used when two or more electrical terminals are installed on a single lug of a terminal strip is. Stacking. Stacking.

The generating system of an aircraft charges the battery by using. constant voltage and varying current. constant voltage and varying current.

When the starter switch to the aircraft gas turbine engine starter-generator is energized and the engine fails to rotate, one of the probable causes would be the. starter solenoid is defective. starter solenoid is defective.

What is the smallest terminal stud allowed for aircraft electrical power systems?. No. 10. No. 10.

When selecting an electrical switch for installation in an aircraft circuit utilizing a direct current motor,. a derating factor should be applied. a derating factor should be applied.

What is the frequency of most aircraft alternating current?. 400 Hertz. 400 Hertz.

How many hours will a 140 ampere-hour battery deliver 15 amperes?. 9.33 hours. 9.33 hours.

In order to reduce the possibility of ground shorting the circuits when the connectors are separated for maintenance, the AN and MS electrical connectors should be installed with the. pin section on the ground side of the electrical circuit. pin section on the ground side of the electrical circuit.

(1) Electrical wires larger than 10 gauge use uninsulated terminals. (2) Electrical wires smaller than 10 gauge use uninsulated terminals. Regarding the above statements,. No. 1 is true. No. 1 is true.

Upon what does the output frequency of an ac generator (alternator) depend?. The speed of rotation and the number of field poles. The speed of rotation and the number of field poles.

As the flux density in the field of a dc generator increases and the current flow to the system increases, the. force required to turn the generator increases. force required to turn the generator increases.

What is the ampere-hour rating of a storage battery that is designed to deliver 45 amperes for 2.5 hours?. 112.5 ampere-hour. 112.5 ampere-hour.

According to the electron theory of the flow of electricity, when a properly functioning dc alternator and voltage regulating system is charging an aircraft's battery, the direction of current flow through the battery. is into the negative terminal and out the positive terminal. is into the negative terminal and out the positive terminal.

When installing electrical wiring parallel to a fuel line, the wiring should be. above the fuel line. above the fuel line.

What is the purpose of a reverse-current cutout relay?. It opens the main generator circuit whenever the generator voltage drops below the battery voltage. It opens the main generator circuit whenever the generator voltage drops below the battery voltage.

As a general rule, starter brushes are replaced when they are approximately. 1/2 their original length. 1/2 their original length.

The maximum allowable voltage drop between the generator and the bus bar is. 2 percent of the regulated voltage. 2 percent of the regulated voltage.

What device is used to convert alternating current, which has been induced into the loops of the rotating armature of a dc generator, to direct current?. A commutator. A commutator.

(Refer to Figure 4.) In a 28-volt system, what is the maximum continuous current that can be carried by a single No. 10 copper wire 25 feet long, routed in free air?. 35 amperes. 35 amperes.

What type of electric motor is generally used with a direct-cranking engine starter?. Direct current, series-wound motor. Direct current, series-wound motor.

Electrical switches are rated according to the. voltage and the current they can control. voltage and the current they can control.

Which of the following Federal Aviation Regulations require that all aircraft using fuses as the circuit protective devices carry 'one spare set of fuses, or three spare fuses of each kind required'?. 14 CFR Part 91. 14 CFR Part 91.

What precaution is usually taken to prevent electrolyte from freezing in a lead acid battery?. keep battery fully charged. keep battery fully charged.

When a 28 volt, 75 ampere generator is installed on an aircraft, an electrical load analysis ground check is performed and it is determined that the battery is furnishing 57 amperes to the system, with all electrical equipment operating. This indicates. the load will be within the generator load limit. the load will be within the generator load limit.

What type of lubricant may be used to aid in pulling electrical wires or cables through conduits?. Soapstone talc. Soapstone talc.

Electrical circuit protection devices are installed primarily to protect the. wiring. wiring.

Which of the following aircraft circuits does NOT contain a fuse/circuit breaker?. starter circuit. starter circuit.

As the generator load is increased (within its rated capacity), the voltage will. remain constant and the amperage output will increase. remain constant and the amperage output will increase.