option
Cuestiones
ayuda
daypo
buscar.php

Preguntas 😾

COMENTARIOS ESTADÍSTICAS RÉCORDS
REALIZAR TEST
Título del Test:
Preguntas 😾

Descripción:
Monty 1809372

Fecha de Creación: 2026/11/17

Categoría: Otros

Número Preguntas: 101

Valoración:(0)
COMPARTE EL TEST
Nuevo ComentarioNuevo Comentario
Comentarios
NO HAY REGISTROS
Temario:

Texto: Lavatory auxiliary lighting ____________ of a 28 V lamp in the lavatory. a. consisting. b. consisted in. c. consists. d. are consisting.

Texto: 29. Examine the history or defect card, if there is one, to find defective areas which you must look at. ____________ and examine the components (See TASK 57-43-22-100- 801-A01 and TASK 57-43-22-210-801-A01) to find the condition and/or the cause of the problem, if there is one. a. You must clean. b. You must to clean. c. You must for clean.

Texto: 15. elect true or false about the following statement: "A polyurethane top coat is applied to protect against chemical or corrosion.". True. False.

Texto: 5- What does eddy current measure?. a. volume. b. the heat. c. electrical conductivity.

Texto: 5. The ____________ diameter of bushes may ____________ increased. a. Outer – are. b. Thickness – is. c. Inner – be.

Texto: 16- When a charge consists of different thicknesses, ____________ overlapping material, anddoes not include clad, use the soaking period for the thickest. Select thicknesscombinations so that this period is not more than four times the minimum requirementfor the thinnest section. a. assemlyes. b. assemblies. c. assemblis.

Texto: Make sure that no sign of sun or heat damage ____________ in the escape rope. a. is present. b. presenting. c. presented. d. present is.

Texto: 22- WARNING - The Export Control or Intellectual Property language on this page takes precedence over any such language that ____________ on subsequent pages of this document. a. should appear. b. must appear. c. may appear.

Texto: 12- Equipment shall be provided to clean material in accordance with 3.3.1.1. Where toxic or harmful cleaners are employed, they shall be used in compliance with the applicable health and safety regulations. The word "applicable" in the previous reading is closest in meaning to: a. Suitable. b. Useless. c. Different.

Texto: 21- ____________ anodized coating from rivets before heat treatment. a. Do not remove. b. Not to remove. c. NOT REMOVE.

Texto: 18. Delamination of joints ____________ where the mechanical bulb seal section joins the diaphragm seal section on the door seals. The fabric-reinforced rubber which forms the joint peels loose from the mechanical or diaphragm seal. Primary cause of this failure is poor bonding. a. occurs. b. occur. c. occuring.

Texto: 29- Forgings that will be in a stress relieved temper such as -TXX51, -TXX52, or -TXX54 can be quenched in cold water. With BR&T approval, quench other forgings in cold water if tests or past experience has proven that residual stresses ____________. a. will not decrease service performance. b. is not decrease service performance. c. not going to decrease service performance.

Texto: The phrase build-up is closed to the meaning: a. A gradual accumulation or increase. b. A gradual reduction or decrease.

Texto: 20- Before heat treatment, clean the parts to remove forming lubricants, marking fluids, or other unwanted material that can cause blistering, surface attack, or staining ____________ subsequent processing. Remove anodized coating before heat treatment. a. from. b. while. c. during.

Texto: Cleaning materials are ____________ flammable and skin irritant. a. is poisonous. b. is poisoning. c. must be poisoned. d. poisonous.

Texto: 2. Composite structures ____________ a surface treatment ____________ them against the effects of lighting strike, ultra violet rays and erosion. a. Have – to protect. b. Had – to be protected. c. Has – to protects.

Texto: 25- Dump the rivets into a perforated container that is submerged in water for quenching. This quickly ____________ the rivets to prevent low mechanical properties or inter-granular corrosion. a. quenches. b. quench. c. quenching.

Texto: 24- Before parts are put into solution heat treatments, make sure the furnaces and salt baths ____________ at the specified heat treating temperature. a. be. b. are. c. is.

Texto: 38. WHY DO WE HAVE TO USE ONLY SPECIFIED CLEANING MATERIALS AND SOLUTIONS OR THEIR EQUIVALENTS?. a. BECAUSE THE SURFACE PROTECTION COULD BE DAMAGED IF UNSPECIFIED MATERIALS ARE USED. IT IS IMPORTANT THAT THE MANUFACTURER'S MIXING, APPLICATION AND TREATMENT INSTRUCTIONS ARE FOLLOWED. b. BECAUSE WE HAVE TO BE CAREFUL IN NOT MIXING DIFFERENT CHEMICALS THAT MAY CAUSE DAMAGE TO OUR PHYSICAL INTEGRITY.

Texto: 14- What is the correct definition of "surplus"?. a. Something that misses from something to be complete. b. something that remains above what is used or needed. c. A shortage of something.

Texto: 20. Make all of the seal repairs with the seal in a position for easy access and when the load on the seal is as small as possible. What happens with seals that are installed?. a. For seals that are installed, it may not be necessary to remove parts of the seal retainer to do work on the damaged area. b. For seals that are installed, it may be necessary to remove parts of the seal retainer to do work on the damaged area. c. For seals that are installed, it may be necessary to remove parts of the seal retainer to do work on the complete area.

Texto: 26- This specification ____________ the requirements for heat treatment of aluminum alloys. Annealing, solution treatment, precipitation treatment and stress relief requirements are included. a. stablishs. b. establish. c. establishes.

Texto: 7. Shrink the bush by freezing it in liquid nitrogen for a minimum period of 1 minute for each millimeter or inch equivalent of thickness to calculate the soaking time. What is the meaning for this expression Shrink the bush?. a. To become smaller. b. To enlarge the bush. c. To expand the bush.

Texto: 26. Design changes, optional parts, configuration differences and Service Bulletin modifications ____________ different part numbers. a. Must cause. b. Should cause. c. may cause.

Texto: Use only ____________ cleaning materials and solutions, or their equivalent. a. are specified. b. is specified. c. must be specified. d. specified.

Texto: aluminum alloy. a. 23 ribs. b. 25 ribs. c. 24 ribs.

Texto: 4. The protection build-up is not the same in all areas of the aircraft structure. Some components are manufactured from corrosion- resistant material and require no surface protection. The phrase build-up is closed to the meaning: a. A gradual reduction or decrease. b. A gradual accumulation or increase.

Texto: 3- Shall be determined in accordance with ASTM E10 far Brinell hardness or ASTM E18 far Rockwell hardness. Where it is impractical ____________ or configuration, portable hardness testing in accordance with ASTM E110 may be used. a. due to size. b. because size. c. for size.

Texto: 1. The protective treatments ____________ corrosion and a damage; by ____________ aggressive fluids and ____________ erosion protection to metallic structures. a. Is prevented – provides. b. Preventing – provide. c. Prevent – provide.

Texto: The Additional Attendant Panel ____________ different number of buttons depending on different aircraft configurations. a. has. b. is having. c. having. d. are having.

Texto: Continually monitor APU engine parameters to ensure that the APU operates ____________ limits. a. among. b. within. c. on.

Texto: 17. Seals prevent loss of cabin pressure at entry doors, galley service doors, cargo doors, the forward access door, electronic equipment access door, and emergency exit doors. Seals also keep water from ____________ at these door locations. a. entering the airplane. b. entered the airplane. c. enter the airplane.

Texto: 24. Choose if the following statement is true or false: The air intake cowl is attached to the front engine flange with bolts and washers. True. False.

Texto: 14- What is the correct definition of "surplus"? 2. a. Something that misses from something to be complete. b. something that remains above what is used or needed. c. A shortage of something.

Texto: 35. PUT THE ASSEMBLY WITH THE CURVATURE OF THE WINDOW PANES AND THE MOUNTING HOLES ____________. a. AS SHOWN. b. SHOWED. c. AS SHOW.

Texto: 9- Choose the correct word order: a. Calibration Sensor Results. b. Sensor Calibration Results. c. Sensor Results Calibration.

Texto: To keep surfaces absolutely clean, ____________ cotton gloves. a. is wearing. b. are wearing. c. wear. d. wearing.

Texto: 30- Alternative rinsing procedures are permitted when documentation indicates removal of all ____________. a. residue glycols. b. glycol residue. c. residue glycol.

Texto: Cabin attendant seats ____________ attached to partitions or lavatory walls. a. am. b. are. c. is. d. was.

Texto: 1. The protective treatments ____________ corrosion and a damage; by ____________ aggressive fluids and ____________ erosion protection to metallic structures. 3. a. Is prevented – provides. b. Preventing – provide. c. Prevent – provide.

Texto: 6- Select if the following statement is true or false: Aluminum alloy heat treatment can be verified when electrical conductivity measurements are used in conjunction with hardness measurements. True. False.

Texto: 38. WHY DO WE HAVE TO USE ONLY SPECIFIED CLEANING MATERIALS AND SOLUTIONS OR THEIR EQUIVALENTS?. a. BECAUSE THE SURFACE PROTECTION COULD BE DAMAGED IF UNSPECIFIED MATERIALS ARE USED. IT IS IMPORTANT THAT THE MANUFACTURER'S MIXING, APPLICATION AND TREATMENT INSTRUCTIONS ARE FOLLOWED. b. BECAUSE WE HAVE TO BE CAREFUL IN NOT MIXING DIFFERENT CHEMICALS THAT MAY CAUSE DAMAGE TO OUR PHYSICAL INTEGRITY.

Texto: 24- Before parts are put into solution heat treatments, make sure the furnaces and salt baths ____________ at the specified heat treating temperature. a. be. b. are. c. is.

Texto: 16- When a charge consists of different thicknesses, ____________ overlapping material, anddoes not include clad, use the soaking period for the thickest. Select thicknesscombinations so that this period is not more than four times the minimum requirementfor the thinnest section. 1. a. assemlyes. b. assemblies. c. assemblis.

Texto: 20. Make all of the seal repairs with the seal in a position for easy access and when the load on the seal is as small as possible. What happens with seals that are installed?. a. For seals that are installed, it may not be necessary to remove parts of the seal retainer to do work on the damaged area. b. For seals that are installed, it may be necessary to remove parts of the seal retainer to do work on the damaged area. c. For seals that are installed, it may be necessary to remove parts of the seal retainer to do work on the complete area.

Texto: 14- What is the correct definition of "surplus"?. a. something that remains above what is used or needed. b. A shortage of something. c. Something that misses from something to be complete.

Texto: 18. Delamination of joints ____________ where the mechanical bulb seal section joins the diaphragm seal section on the door seals. The fabric-reinforced rubber which forms the joint peels loose from the mechanical or diaphragm seal. Primary cause of this failure is poor bonding. 1. a. occurs. b. occur. c. occuring.

Texto: During repair of painted components, ____________ that there is a good flow of air through the work area. a. make sure. b. making sure. c. to make sure. d. sure make.

Texto: 34. Apply primer, C00259 (F-20.03) but ____________ put primer, C00259 in the holes for the bearing or the fitting. a. Does not. b. Not to. c. Do not.

Texto: 25- Dump the rivets into a perforated container that is submerged in water for quenching. This quickly ____________ the rivets to prevent low mechanical properties or inter-granular corrosion. a. quenches. b. quench. c. quenching.

Texto: ____________ anodized coating from rivets before heat treatment. a. Not to remove. b. Do not remove. c. NOT REMOVE.

Texto: To move the seat, the control handle marked FORE/AFT ____________ operated upwards in order to unlock the seat. a. has to be. b. to be. c. having. d. be.

Texto: What is the meaning for this expression Shrink the bush?. a. To expand the bush. b. To become smaller. c. To enlarge the bush.

Texto: 17- Forgings that ____________ be in a stress relieved temper such as -TXX51, -TXX52, or -TXX54 can be quenched in cold water. a. is. b. will. c. going to.

Texto: 5. The ____________ diameter of bushes may ____________ increased. a. Outer – are. b. Thickness – is. c. Inner – be.

Texto: NOTE : Do not fully ____________ the screws (3) at this time. a. tighten. b. apply. c. start. d. comply.

Texto: 9- Choose the correct word order: a. Calibration Sensor Results. b. Sensor Calibration Results. c. Sensor Results Calibration.

Texto: 5. The ____________ diameter of bushes may ____________ increased. a. Inner – be. b. Outer – are. c. Thickness – is.

Texto: what does PSU stand for?. a. pack serial unit. b. pound servo unit. c. passanger servo unit. d. passenger service unit.

Texto: 25. The three types of repairs are defined as: a. Standard Practice, Minor and Major. b. A and B are correct. c. Normal, wear and tear.

Texto: The phrase build-up is closed to the meaning: a. A gradual accumulation or increase. b. A gradual reduction or decrease.

Texto: 20. Make all of the seal repairs with the seal in a position for easy access and when the load on the seal is as small as possible. What happens with seals that are installed?. a. For seals that are installed, it may be necessary to remove parts of the seal retainer to do work on the complete area. b. For seals that are installed, it may not be necessary to remove parts of the seal retainer to do work on the damaged area. c. For seals that are installed, it may be necessary to remove parts of the seal retainer to do work on the damaged area.

Texto: Seat structure at the flight compartment ____________ aluminum alloy. a. made of. b. is made of. c. made. d. make of.

Texto: Within the adjustment limits ____________ of the armrest is obtained by turning a control switch. a. is lowering. b. lowering. c. lowering is. d. is lowered.

Texto: 15. elect true or false about the following statement: "A polyurethane top coat is applied to protect against chemical or corrosion.". True. False.

Texto: ____________ operate the switches 4WL and LIGHT EMER. a. no to. b. none. c. not to.

Texto: Cleaning materials ____________ dangerous. a. to be. b. is. c. are. b. is.

Texto: The correct order of the imperative sentence is as follows ____________. a. part removal from aircraft. b. to remove part from aircraft. c. remove part from aircraft. d. removing aircraft parts.

Texto: 23. ____________ CERAMIC FIBER DUST. THIS DUST CONTAINS CERAMIC FIBERS THAT MAY CAUSE CANCER. a. NOT TO BREATHE. b. DO NOT BREATHE. c. NOT BREATHE.

Texto: Cleaning materials are ____________ flammable and skin irritant. 1. a. is poisonous. b. is poisoning. c. must be poisoned. d. poisonous.

Texto: Cleaning materials ____________ dangerous. a. is. b. being. c. are. d. to be.

Texto: 29. Examine the history or defect card, if there is one, to find defective areas which you must look at. ____________ and examine the components (...) to find the condition and/or the cause of the problem, if there is one. a. You must to clean. b. You must for clean. c. You must clean.

Texto: 6. ____________ the manufacturer instructions and ____________ the correct protective clothing when you ____________ liquid nitrogen. Liquid nitrogen is dangerous. a. Wear – use – apply. b. Read – apply – use. c. Obey – wear – use.

Texto: 38. WHY DO WE HAVE TO USE ONLY SPECIFIED CLEANING MATERIALS AND SOLUTIONS OR THEIR EQUIVALENTS?. a. BECAUSE THE SURFACE PROTECTION COULD BE DAMAGED IF UNSPECIFIED MATERIALS ARE USED. IT IS IMPORTANT THAT THE MANUFACTURER'S MIXING, APPLICATION AND TREATMENT INSTRUCTIONS ARE FOLLOWED. b. BECAUSE WE HAVE TO BE CAREFUL IN NOT MIXING DIFFERENT CHEMICALS THAT MAY CAUSE DAMAGE TO OUR PHYSICAL INTEGRITY.

Texto: 7- Choose the best definition for furnance: a. Equipment used exclusively for thermal processing of samples, specimens, or test parts as required by materials and processing specifications. b. A mass of material with an embedded sensor or sensors which supplies temperature data of that mass to recording instruments. c. Equipment used for the thermal processing of parts or raw material.

Texto: The number and location of the galleys ____________ with the cabin configuration and the aircraft utilization. a. varying. b. is varying. c. vary. d. varies.

Texto: 32. AFTER THE BUSHINGS ARE FLARED, ____________ FLUSH WITH THE FAYING SURFACES. a. THEY SHOULD BE. b. THEY MUST BE. c. THEY MAY BE.

Texto: 33. Apply enamel coating, C00700 (SRF-14.9813). Internal surfaces ____________ by the fill and drain procedure. Do not put enamel coating, C00032 in the holes for the bushings and the bolts. a. should be finished. b. can be finished. c. Do be finished.

Texto: ____________ the fasteners (1) and remove the screws (2) from the panel (10). a. lost. b. loosen. c. safety. d. apply.

Texto: 10. The slat ____________ a riveted assembly and a trailing-edge assembly. a. is made the. b. is made of. c. are made from.

Texto: ____________ finger in the direction of the arrows and remove the handgrip cover (2). a. careful. b. carefully. c. care. d. caring.

Texto: 32. AFTER THE BUSHINGS ARE FLARED, ____________ FLUSH WITH THE FAYING SURFACES. a. THEY MAY BE. b. THEY SHOULD BE. c. THEY MUST BE.

Texto: aluminum alloy. a. 24 ribs. b. 23 ribs. c. 25 ribs.

Texto: 27- Quench delay time in air furnaces ____________ when the door ____________ to open and ends when the last corner of the load is immersed in the quenchant. a. start/starts. b. started/start. c. starts/starts.

Texto: 11- Soaking solution heat treated parts at a moderately elevated temperature or, for some alloys and tempers, at room temperature ____________ strength and corrosion resistance properties. a. enhance. b. to enhancing. c. to enhance.

Texto: 21. Do not remove components from the aft entry door assembly that are riveted or bonded ____________ replacement is necessary. a. nevertheless. b. unless. c. however.

Texto: Lavatory auxiliary lighting ____________ of a 28 V lamp in the lavatory. 2. a. consisting. b. consisted in. c. consists. d. are consisting.

Texto: 15. elect true or false about the following statement: "A polyurethane top coat is applied to protect against chemical or corrosion". True. False.

Texto: 24- Before parts are put into solution heat treatments, make sure the furnaces and salt baths ____________ at the specified heat treating temperature. 3. a. be. b. are. c. is.

Texto: 28. Three ____________ enhance safety during operation. a. assist handles. b. handles assist. c. assisting handles. d. [...] assists.

Texto: 18- The temperature of the quenchant ____________ more than 20 F (11 C) from quenching one heat treatment load. The maximum quenchant temperature at the start of quench must be 90 F (32 C). a. might not increase. b. must not increase. c. should not increase.

Texto: There are dry galleys and wet galleys ____________. a. installing. b. is installed. c. install. d. installed.

Texto: 23. ____________ CERAMIC FIBER DUST. THIS DUST CONTAINS CERAMIC FIBERS THAT MAY CAUSE CANCER. a. NOT BREATHE. b. NOT TO BREATHE. c. DO NOT BREATHE.

Texto: 12- Equipment shall be provided to clean material in accordance with 3.3.1.1. Where toxic or harmful cleaners are employed, they shall be used in compliance with the applicable health and safety regulations. The word "applicable" in the previous reading is closest in meaning to: a. Suitable. b. Useless. c. Different.

Texto: 24. Choose if the following statement is true or false: The air intake cowl is attached to the front engine flange with bolts and washers. True. False.

Texto: 4- Electrical Conductivity ____________ in accordance with ASTM E1004 or MIL-STD-1537. a. is be determined. b. Shall be determined. c. maight be determined.

Texto: The cockpit seats ____________. a. is electrically and manually operating. b. are electrically and manually operate. c. is electrically and manually operated. d. are electrically and manually operated.

Texto: 10- Choose the correct word order: a. Raw Material Heat Treatment. b. Raw Material Treatment Heat. c. Heat Treatment Raw Material.

Texto: Be careful when you are above the ceiling. Damage to ducts, wire bundles, ____________ and support braces can occur. a. panel ceiling. b. panelling ceiling. c. ceiling panelling. d. ceiling panel.

Texto: 28. Do not remove components from the aft entry door assembly that are riveted or bonded ____________ replacement is necessary. a. unless. b. therefore. c. however.

Texto: 30. CAUTION : DO ALL THE WORK ON A CLEAN, SOFT SURFACE ____________ DAMAGE TO THE COMPONENTS. a. for prevents. b. to prevent. c. for prevent.

Denunciar Test