Proficiency FAA

Which APNs are used to see flight hours and flight cycles of ab aircraft? (Multiple choise). 308. 1418. 206. 147.

The Avianca Quality Control Manual has been developed in accordance with: APPROVED MAINTENANCE MANUAL. MASTER MINIMUN EQUIPMENT LIST. AC-145-9; FAR 145.211.

If you need for your trainig requirements under FAA regulations. To which manial do you need to refer?. RSM. QCM. RSTPM. MET-TAR.

Quality Control area performs an internal Self Evaluation to verify the availability of Housing & Facilites, technical data, ____________, Materials, training, personnel and other special considerations. DOCUMENTS. MAINTENANCE RECORDS. CAPABILITY LIST. TOOLS & EQUIPMENTS.

What kind of inspection is associated to this procedure definition: Evaluating the articles that have been involved in accidents or incidents or normal maintenance procedures that includes a search for any seccondary damage such as fire or heat damage. IN-PROCESS INSPECTION. PRELIMINARY INSPECTION. FINAL INSPECTION. HIDDEN DAMAGE INSPECTION.

Which FAR part is related to Inspection personnel requirements?. 145.155. 145.163. 145.151.

Write at least 5 opertaional certificates with which the Repair Station - Organización de Mantenimiento certify its works: ANAC B-145, CDF-003, MU1Y335K, MU1Z335K, & EASA 147,0032. CMAE E-760, CDF-003, MU1Y335K, MU1Z335K & EASA 147,0027. CMAE E-670, CDF-003, MU1Y335C, MU1Z335K & EASA 147,0027. CMAE E-670, OMA-003, MU1Y335C, MU1Z335K & EASA 147,0027.

According to the classifications of tools and equipment, to which class corresponds: Equipment that calibration is not required but has specified preventive maintenance procedure by the manufacturer. This equipment and tools will be identified with a placard that established the accomplished of preventive maintenance and its S/N. CLASS 1. CLASS 2. CLASS 3. ALL ANSWERS ARE CORRECT.

With your own words, what is the "Component Service Report" form used for?: The Component Service Report form is used by the workshop incoming inspection and its purpose is guide thru the various steps from receiving the article to release to service the disassembly, test/inspection/repair/overhaul and assembly of the article in order to record the compliance of the maintenance process. The Component Service Report form is used by the workshop incoming inspection and its purpose is guide thru the various steps from receiving the article to release to service the disassembly, test/inspection/repair/overhaul and assembly of the article in order to record the compliance of the inspection process. The Component Service Report form is used by the workshop personnel an its purpose is guide thru the various steps from receiving the article to release to service the disassembly, test/inspection/repair/overhaul and assembly of the article in order to record the compliance of the maintenance process and inspection phases. None of the above.

In accordance with CFR par 21.175, the airworthiness certificate are divided into: STANDARD AIRWORTHINES CERTIFICATES. SPECIAL AIRWORTHINESS CERTIFICATES. A AND B ARE TRUE.

IF DURING THE VERIFICATION, A TOOL IS NECESSARY CHECK THE TOOL CONDITION AND THE CALIBRATION LABEL. VERDADERO. FALSO.

What is a Major Alteration?. a. That may appreciably affect the airworthiness do to changes in weight and balance, resistance behavior structural, engine operation or flight characteristics. b. Que no se peude dar de acuerdo a prácticas aceptadas o que no se puede hacer por una operación elemental. c. Cualquier alteración que no esté calificada como una alteración menor. d. A & B.

In which manual are the duties and responsibilities of the incoming inspector?. RSM. GMM. QCM.

If any product or article fails to meet applicable requirements durng the incoming inspection, it will be: STORED. QUARANTINED. DISCARD.

Part 21 of CFR talks about: CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS. INVESTIGATIVE AND ENFORCEMENT PROCEDURES. AIRWORTHINESS STANDARS: NORMAL CATEGORY ROTORCRAFT.

If you need to review your employment summary, in which APN can you do it?. 10250. 10083. 10251.

In which chapter of th QCM are the measurement and calibration equipment policies?. 9. 10. 8.