Tml y cambio de plaza

Before heat treatment, clean the parts to remove forming lubricants, marking fluids, or other unwanted material that can cause blistering, surface attack, or staining _ subsequent processing. Remove anodized coating before heat treatment. from. while. during.

What is the correct definition of "surplus"?. Something that misses from something to be complete. something that remains above what is used or needed. shortage of something.

Continually moritor APU engine parameters to ensure that the APU operates_ _limits. among. within. On.

Before parts are put into solution heat treatments, make sure the furnaces and sait baths at the specified heat treating temperature. Be. Are. Is.

The protective treatments— aggressive fluids and _ — corrosion and a damage by erosion protection to metallic structures. Is prevented - provides. Preventing - provide. Prevent- provide.

Choose the correct word order: Raw Material Heat Treatment. Raw Material Treatient Heat. Heat Treatment Raw Material.

Dump the rivets into a pertorated container that is submerged in water for quenching. This quickly the rivets to prevent low mechanical properties or inter granular corrosion. quenches. quench. quenching.

Do not remove components from the aft entry door assembly that are riveted or bonded — _ replacement is necessary. unless. therefore. however.

Linear areas that are not more than 0.25 inch wide _ permitted to touch. Is. Be. Are.

This specification the requirements for heat treatment of aluminum alloys. Annealing, solution treatment, precipitation treatment and stress relief requirements are included. stablishs. establish. establishes.

The protective treatments - aggressive fluids and corrosion and a damage by _erosion protection to metallic structures. Is prevented - provides. Preventing - provide. Prevent- provide.

Alternative rinsing procedures are permitted when documentation indicates removal of all. residue glycols. glycol residue. residue glycol.

Use only. _cleaning materials and solutions, or their equivalent. are specified. is specified. specified.

aluminum alloy. 23ribs. 25ribs. 24ribs.

Seals prevent loss of cabin pressure at entry doors, galley service doors, cargo doors, the forward access door, electronic equipment access door, and emergency exit doors. Seals also keep water from _ _ at these door locations. entering the airplane. entered the airplane. enter the airplane.

Delamination of joints where the mechanical bulb seal section joins the diaphragm seal section on the door seals. The fabric-reinforced rubber which forms the joint peels loose from the mechanical or diaphragm seal. Primary cause of this failure is poor bonding: Occurs. Occur. Occuring.

The protection build-up is not the same in all areas of the aircraft structure. Some components are manufactured from corrosion- resistant material and require no surface protection. The phrase buildup is closed to the meaning: A gradual reduction or decrease. A gradual accumulation or increase.

The Additional Attendant Panel different number of buttons depending on different aircraft configurations. has. is having. are having.

PUT THE ASSEMBLY WITH THE CURVATURE OF THE WINDOW PANES AND THE MOUNTING HOLES. As shown. SHOWED. AS SHOW.

finger in the direction of the arrows and remove the handgrip cover (22). Careful. Carefullyn. Care.

To keep surfaces absolutely clean,_ _cotton gloves. is wearing. are wearing. Wear.

the fasteners (1) and remove the screws (2) from the panel (10). Lost. Loosen. Safety.

Do not fully _ the screws (3) at this time. tighten. apply. start.

What is the meaning for this expression Shrink the bush?. To expand the bush. To become smaller. To enlarge the bush.

Examine the history or defect card, if there is one, to find defective areas which you must look at. and examine the components (See TASK 57-43-22-100- 801-A01 and TASK 57-43-22-210-801- A01) to find the condition and/or the cause of the problem, if there is one. You must to clean. You must for clean. You must clean.

During repair of painted components, that there is a good flow of air through the work area. make sure. making sure. to make sure.

Caution do all the work on a clean soft surface damage to the components. for prevents. to prevent. for prevent.

When a charge consists of different thicknesses, overlapping material, anddoes not include clad, use the soaking period for the thickest. Select thicknesscombinations so that this period is not more than four times the minimum requirementfor the thinnest section. assemiyes. assemblies. assemblis.

Do not fully the screws (3) ay this time. Comply. Apply. tighten.

Soaking solution heat treated parts at a moderately elevated temperature or, for sorne alloys and tempers, at room temperature strength and corrosion resistance properties. enhance. to enhancing. to enhance.

Lavatory auxiliary lighting __of a 28 V lamp in the lavatory. consisting. consisted in. consists.

Cabin attendant seats attached to partitions or lavatory walls. Am. Are. Is.

The three types of repairs are defined as: Standard Practice, Minor and Major. A and B are correct. Normal, wear and tear.

To move the seat, the control handle marked FORE/AFT_ _operated upwards in order to unlock the seat. has to be. to be. having.

CERAMIC FIBER DUST. THIS DUST CONTAINS CERAMIC FIBERS THAT MAY CAUSE CANCER. NOT TO BREATHE. DO NOT BREATHE. NOT BREATHE.

Forgings that be in a stress relieved temper such as -TXX51, -TXX52, or - TXX54can be quenched in cold water. Is. Will. Going to.

Choose it the following statement is true or false: The air intake cowl is attached to the front engine flange with bolts and washers. True. Falce.

Choose the correct word order: Calibration Sensor Results. Sensor Calibration Results. Sensor Results Calibration.

the aft entry door from outside the airplane, you pull the outer handle from the spring-loaded flush position. When you turn the handle, the torque tube pulls the latch rollers from the latch fittings to let the door move out to the side structure. For open. To open. For to open.

Make all of the seal repairs with the seal in a position for easy access and when the load on the seal is as small as possible. What happens with seals that are installed?. For seals that are installed, it may be necessary to remove parts of the seal retainer to do work on the complete area. For seals that are installed, it may not be necessary to remove parts of the seal retainer to do work on the damaged area. For seals that are installed, it may be necessary to remove parts of the seal retainer to do work on the damaged area.

AFTER THE BUSHINGS ARE FLARED, FLUSH WITH THE FAYING SURFACES. THEY SHOULD BE. THEY MUST BE. THEY MAY BE.

The protective treatments______ corrosion and a damage by aggressive fluids and_______ erosion protection to metallic structures. Is prevented - provides. Prevent- provide. Preventing - provide.

5. The diameter of bushes may _ increased. Outer - are. Thickness - is. Inner - bel.

_______anodized coating from rivets before heat treatment. Not to remove. Do not remove. NOT REMOVE.

elect true or false about the following statement: "A polyurethane top coat is applied to protect against chemical or corrosion. True. Falce.

Alternative rinsing procedures are permitted when documentation indicates removal of all_. residue glycols. glyco residue. residue glycol.

what does PSU stand for?. pack serial unit|. passenger service unit. passenger servo unit.

Cleaning materials__dangerous. to be. Is. Are.

Choose the best definition for furnance: Equipment used exclusively for thermal processing of samples, specimens, or test parts as required by materials and processing specifications. A mass of material with an embedded sensor or sensors which supplies temperatüre data of that mass to recording instruments. Equipment used for the thermal processing of parts or raw material.

The temperature of the quenchant_____ more than 20 F (11 C) fromquenching one heat treatment load. The maximum quenchant temperature at the startof quench must be 90 F (32 C). must not increase. might not increase. should not increase.

The____ diameter of bushes my___ increased. Inner - be. Outer - are. Thickness - is.

the manufacturer instructions and _ the correct protective clothing when you _ liquid nitrogen. Liquid nitrogen is dangerous. Wear - use - apply. Read - apply - use. Obey - wear - use.

Use only the specified materials and the instructions from the manufacturers. are obeying. is obeying. obey.

Electrical Conductivity _in accordance with ASTM E1004 or MIL STD-1537. is be determined. Shall be determined. maight be determined.

Seat structure at the flight compartment__aluminum alloy. made of. is made of. made.

Be careful when you use chemical materials.________ the material manufacturer instructions and the local regulations. Obey. To obey. you Obey.

Three enhance safety during operation. assist handles. handles assist. assisting handles.

Make sure that no sign of sun or heat damage_in the escape rope. presenting. present is. presented.

careful when you are above the ceiling. Damage to ducts, wire bundles, and support braces can occur. ceiling panel. ceiling panelling. panelling ceiling.

Design and Manufacturing requirements of the above breakdown the same as those in the ATA Specification and the IPL. Are no always be. A and B are correct. will not always be.

What is mandatory?. The appropriate surface protection will be applied afterwards the repair is accomplished. The applicable surface protection will be applied previously the repair is initiated.

The temperature of the quenchant more than 20 F (11 C) fromquenching one heat treatment load. The maximum quenchant temperature at the startof quench must be 90 F (32 C). might not increase. must not increase. should not increase.

Within the adjustment limits of the armrest is by turning a control switch. is lowered. lowering is. lowering.

chamois leather. weak. week. wack.

Cleaning agent_. to be dangerous. dangerous. danger.

The numberand location of the galleys_ with the cabin configuration and the aircraft utilization. varying. is varying. vary.

The correct order of the imperative sentence is as follows_. part removal from aircraft. to remove part from aircraft. remove part from aircraft.

WHY DO WE HAVE TO USE ONLY SPECIFIED CLEANING MATERIALS AND SOLUTIONS OR THEIR EQUIVALENTS?. BECAUSE THE SURFACE PROTECTION COULD BE DAMAGED IF UNSPECIFIED MATERIALS ARE USED. IT IS IMPORTANT THAT THE MANUFACTURER'S MIXING, APPLICATION AND TREATMENT INSTRUCTIONS ARE FOLLOWED. BECAUSE WE HAVE TO BE CAREFUL IN NOT MIXING DIFFERENT CHEMICALS THAT MAY CAUSE DAMAGE TO OUR PHYSICAL INTEGRITY.

Make sure that this (these) _(s) is (are) open, safetied and tagged. circuit breaker. rectifier. fuse.

AFTER THE BUSHINGS ARE FLARED, FLUSH WITH THE FAYING SURFACES. THEY MAY BE. THEY SHOULD BE. THEY MUST BE.

The slat________a riveted assembly and a trailing-edge assembly. is made the. is made of. are made from.

There are dry galleys and wet galleys_. is installed. install. installed.

Apply enamel coating, C00700 (SRF-14.9813), Internal surfaces______ the fill and drain procedure. Do not put enamel, C00032 in the holes for the bushings and the bolts. should be finished. can be finished. Do be finished.

elect true or false about the following statement: "A polyurethane top coat is applied to protect against chemical or corrosion.". Falce. True.

Cleaning materials are. flammable and skin iritant. poisonous. must be poisoned. is poisoning.

Do not remove components from the aft entry door assembly that are riveted or bonded replacement is necessary. nevertheless. unless. however.

Equipment shall be provided to clean material in accordance with 3.3.1.1. Where toxic or harmful cleaners are employed, they shall be used in compliance with the applicable health and safety regulations. The word "applicable" in the previous reading is closest in meaning to: Suitable. Useless. Different.